Home › BODY ELECTRICAL › DOOR LOCK › SMART KEY SYSTEM

SMART KEY SYSTEM > Driver Side Door Entry Unlock Function does not Operate

for Preparation Click here


DESCRIPTION

When an ID code from the door electrical key oscillator LH matches an ID code from the key, the certification ECU outputs a SEL1 signal (Lo when output) to the door electrical key oscillator LH, activates the touch sensor inside the outside door handle, and enters unlock standby condition. When the touch sensor is touched, the electrical key oscillator LH sends a SENS signal (Lo when output) to the certification ECU and the certification ECU sends an unlock signal to the driver door lock.

WIRING DIAGRAM


B128890E01


INSPECTION PROCEDURE

1.CHECK MANUAL DOOR UNLOCK OPERATION
  1. Check that the manual door unlock function operates normally.

    OK:
    Manual door unlock function operates normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM
OK


2.CHECK DOOR ELECTRICAL KEY OSCILLATOR LH (SEL VOLTAGE)
B080049E02
  1. Measure the voltage between the terminals of the connector when the key is operated.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D16-2 (SEL) - D16-8 (GND)
    Key at least 5 m (16.4 ft.) away from door
    10 to 14 V
    Key within 0.7 m (2.3 ft.) from door
    Below 1 V



NG
Go to step 7
OK


3.CHECK DOOR ELECTRICAL KEY OSCILLATOR LH (SENS VOLTAGE)
B080049E03
  1. Measure the voltage between the terminals of the connector when the outside door handle is touched.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D16-3 (SENS) - D16-8 (GND)
    Outside door handle not touched
    10 to 14 V
    Outside door handle touched
    Below 1 V



OK
Go to step 5
NG


4.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR LH - CERTIFICATION ECU)
B079781E03
  1. Disconnect the D16 oscillator connector.

  1. Disconnect the S11 ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D16-3 (SENS) - S11-21 (SEN1)
    Below 1 Ω
    D16-3 (SENS) or S11-21 (SEN1) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.CHECK OPERATION OF DOOR ELECTRICAL KEY OSCILLATOR LH
  1. After replacing the door electrical key oscillator on the driver's side with a new one, check that the entry unlock function operates normally.

    OK:
    Entry unlock function operates normally.



OK
REPLACE DOOR ELECTRICAL KEY OSCILLATOR LH
NG


6.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR LH - ELECTRICAL KEY ANTENNA)
B079782E01
  1. Disconnect the D16 oscillator connector.

  1. Disconnect the E8 antenna connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D16-6 (ANT1) - E8-5 (ANT1)
    Below 1 Ω
    D16-7 (ANT2) - E8-2 (ANT2)
    Below 1 Ω
    D16-5 (SGT) - E8-6 (SGT)
    Below 1 Ω
    D16-8 (GND) - Body ground
    Below 1 Ω
    D16-6 (ANT1) or E8-5 (ANT1) - Body ground
    10 kΩ or higher
    D16-7 (ANT2) or E8-2 (ANT2) - Body ground
    10 kΩ or higher
    D16-5 (SGT) or E8-6 (SGT) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ELECTRICAL KEY ANTENNA LH 

7.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR LH - CERTIFICATION ECU)
B079781E04
  1. Disconnect the D16 oscillator connector.

  1. Disconnect the S11 ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D16-2 (SEL) - S11-23 (SEL1)
    Below 1 Ω
    D16-2 (SEL) or S11-23 (SEL1) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE CERTIFICATION ECU