Home › BODY › INSTRUMENT PANEL › INSTRUMENT PANEL SAFETY PAD

INSTRUMENT PANEL SAFETY PAD > REMOVAL

for Preparation Click here



1. TABLE OF BOLT, SCREW AND NUT

HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with an alphabetical code in the table below.

B074072E03



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



3. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


B074044E02
  1. Detach the 2 claws and 4 clips, and remove the instrument panel register.



4. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


B074045E02
  1. Remove the 2 screws.

  1. Disconnect the hood lock control cable.

  1. Detach the 4 claws and 5 clips.

  1. Disconnect all connectors and remove the instrument panel finish panel.



5. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


B074046E02
  1. Detach the 3 claws and 4 clips.

  1. Disconnect the connector and remove the instrument panel finish panel.



6. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


B074047E02
  1. Detach the claw and 5 clips.

  1. Disconnect the connector and remove the instrument panel register.



7. REMOVE NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY


B074048E02
  1. Detach the 6 clips and remove the instrument panel register.



8. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


B074049E02
  1. Detach the 2 claws and 4 clips, and remove the instrument panel register.



9. REMOVE MULTI-DISPLAY ASSEMBLY


10. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY


B074050E01
  1. Holding the part indicated in the illustration, remove the glove compartment door stopper from the glove compartment door.



11. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


B074051E02
  1. While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, open the door to release it from the 2 stoppers.

  1. Open the door until it is horizontal.



    B074052E02
  1. Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.



12. REMOVE INSTRUMENT PANEL CUSHION


13. REMOVE INSTRUMENT CLUSTER FINISH PANEL END


14. REMOVE INSTRUMENT PANEL HOLE COVER
  1. Using a screwdriver, remove the 2 instrument panel hole covers.



15. REMOVE GLOVE COMPARTMENT DOOR


B074053E02
  1. Remove the 2 screws.

  1. Detach the claw and 2 clips, and remove the glove compartment door.



16. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (w/ JBL Sound System)


17. REMOVE FRONT PILLAR GARNISH CORNER PIECE LH


    B136013E01
  1. Put protective tape as shown in the illustration.

    Standard measurement:
    Area
    Specified Condition
    A
    2.0 mm (0.079 in.)
    B
    10.0 mm (0.394 in.)
    C
    50.0 mm (1.969 in.)

  1. Attach the 5 claws to install the corner piece.



18. REMOVE FRONT PILLAR GARNISH CORNER PIECE RH

HINT:
Use the same procedures described for the LH side.



19. REMOVE FRONT PILLAR GARNISH LH


    B073594E03
  1. w/o Curtain Shield Airbag:
    Attach the 2 clips to install the pillar garnish.

  1. w/ Curtain Shield Airbag:
    Remove the protective cover.



  1. w/ Curtain Shield Airbag:
    Install the pillar garnish.



      B132621E01
    1. Set the claws of the pillar garnish to the area labeled C.

    2. Insert the tip of clip A into the pillar garnish's hole.

    3. Using needle-nose pliers, rotate the tip of clip A 90°. Then push the pillar garnish toward the vehicle body to attach the base of clip A and clip B.



20. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



21. DISCONNECT PASSENGER AIRBAG CONNECTOR


22. REMOVE INSTRUMENT PANEL SAFETY PAD
  1. Remove the 3 screws.

  1. Remove the 2 bolts.

  1. Pull up the instrument panel to detach the 6 claws and 3 clips.



  1. Remove the instrument panel.


    B075862E02