Home › HYBRID SYSTEM › P112 HYBRID BATTERY CONTROL › HV BATTERY

HV BATTERY > DISASSEMBLY

for Preparation Click here



1. REMOVE BATTERY COVER


    A083610E01
  1. Remove the protector shown in the illustration.



  1. Remove the 6 bolts, 2 nuts, clip, battery cover and battery carrier catch bracket.


    A083611E01



2. REMOVE NO. 1 WIRE HARNESS PROTECTOR COVER


A083582E02

CAUTION:
Wear insulating gloves.



3. REMOVE NO. 3 WIRE HARNESS PROTECTOR COVER

CAUTION:
Wear insulating gloves.



4. REMOVE NO. 3 BATTERY CARRIER CUSHION


A077542E01

CAUTION:
Wear insulating gloves.

  1. Peel off the bonded parts, then remove the battery carrier cushion.



5. REMOVE MAIN BATTERY CABLE


A125183E01

CAUTION:
Wear insulating gloves.

  1. Remove the terminal cover shown in the illustration.



    A083551E01
  1. Remove the nut, then disconnect the aluminum shield wire.

  1. Remove the nut, then disconnect the main battery cable from the No. 3 system main relay.

  1. Remove the nut, then disconnect the main battery cable from the No. 2 frame wire.

  1. Remove the main battery cable from the HV battery.



6. REMOVE NO. 2 MAIN BATTERY CABLE


A083580E01

CAUTION:
Wear insulating gloves.

  1. Remove the terminal cover shown in the illustration.



    A083566E02
  1. Remove the nut, then disconnect the system main relay terminal and No. 2 main battery cable from the No. 2 system main relay.

  1. Remove the nut, then disconnect the No. 2 main battery cable from the frame wire.

  1. Remove the No. 2 main battery cable from the HV battery.



7. REMOVE BATTERY CURRENT SENSOR


A083579E01

CAUTION:
Wear insulating gloves.

  1. Remove the terminal cover.



    A083638E01
  1. Remove the nut, then disconnect the main battery cable.



    A083564E01
  1. Disconnect the connector.

  1. Remove the 2 screws and battery current sensor.



8. REMOVE NO. 2 WIRE HARNESS PROTECTOR COVER


A083565E02

CAUTION:
Wear insulating gloves.



9. REMOVE NO. 4 WIRE HARNESS PROTECTOR COVER

CAUTION:
Wear insulating gloves.



10. REMOVE BATTERY CLAMP PAD


A077541E01

CAUTION:
Wear insulating gloves.

  1. Peel off the bonded parts, then remove the battery clamp pad (the battery carrier cushion).



11. REMOVE NO. 1 WIRE HARNESS PROTECTOR COVER


    A077550E02
  1. Open the wire harness protector cover.

  1. Remove the 2 nuts, then disconnect the service plug.

  1. Remove the wire harness protector cover.



12. REMOVE BATTERY PLUG


    A077543E01
  1. Disconnect the connector clamp.

  1. Remove the 2 bolts, then disconnect the service plug from the upper battery carrier.



    A077544E03
  1. Open the wire harness protector cover as shown in the illustration. Then remove the service plug from the junction block.



13. REMOVE JUNCTION BLOCK


A083549E01

CAUTION:
Wear insulating gloves.

  1. Remove the 26 nuts and junction block.



14. REMOVE NO. 2 SYSTEM MAIN RELAY


A083581E01

CAUTION:
Wear insulating gloves.

  1. Remove the 2 terminal covers.



    A077540E03
  1. Remove the nut, then disconnect the system main battery relay terminal and main battery cable.



    A077539E01
  1. Disconnect the connector.

  1. Remove the 2 nuts and No. 2 system main relay.



15. REMOVE NO. 3 SYSTEM MAIN RELAY


A077538E01

NOTICE:
Wear insulating gloves.

  1. Remove the nut, then disconnect the main battery cable.

  1. Remove the 2 nuts, then disconnect the No. 3 system main relay.

  1. Disconnect the connector and remove the No. 3 system main relay.



16. REMOVE SYSTEM MAIN RESISTOR


A083568E01

CAUTION:
Wear insulating gloves.

  1. Disconnect the connector from the No. 1 system main relay.

  1. Remove the bolt and system main resistor.



17. REMOVE NO. 1 SYSTEM MAIN RELAY

CAUTION:
Wear insulating gloves.

  1. Disconnect the connector.

  1. Remove the nut, then disconnect the ground terminal.

  1. Disconnect the 2 clamps.

  1. Remove the system main relay connector.



  1. Remove the 2 bolts and No. 1 system main relay.


    A092580E01



18. REMOVE BATTERY ECU


A083606E02

CAUTION:
Wear insulating gloves.

  1. Disconnect the system main relay connector.

    CAUTION:
    Insulate the disconnected connectors with insulating tape.

  1. Disconnect the battery ECU connector.

    CAUTION:
    Insulate the disconnected connectors with insulating tape.

  1. Disconnect the thermistor connector.

    CAUTION:
    Insulate the disconnected connectors with insulating tape.

  1. Remove the clamp, then disconnect the No. 2 frame wire connector.

    CAUTION:
    Insulate the disconnected connectors with insulating tape.



  1. Remove the nut, then disconnect the aluminum shield wire of the main battery cable.


    A083605E01

  1. Remove the 2 screws and battery ECU.



19. REMOVE UPPER BATTERY CARRIER


A077549E01

CAUTION:
Wear insulating gloves.

  1. Remove the 3 nuts and upper battery carrier.



20. REMOVE NO. 2 BATTERY SPACER

CAUTION:
Wear insulating gloves.



21. REMOVE NO. 2 FRAME WIRE


A077536E01

CAUTION:
Wear insulating gloves.

  1. Disconnect the temperature sensor connector from the battery ECU.

  1. Remove the clamp, then disconnect the No. 2 frame wire connector from the battery ECU.



    A089187E01
  1. Remove the 26 nuts and No. 2 frame wire.



22. REMOVE BATTERY ROOM VENTILATION HOSE


A077535E01

CAUTION:
Wear insulating gloves.