Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0128    Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)

for Preparation Click here


DESCRIPTION

HINT:
This is the purpose of detecting the "thermostat" malfunction.

If the engine coolant temperature (ECT) does not reach 75°C (167°F) despite sufficient warm-up time has elapsed.

DTC No.
DTC Detection Condition
Trouble Area
P0128
Conditions (a), (b) and (c) are met:
(a) Cold start
(b) After sufficient warm-up time has elapsed
(c) Engine coolant temperature is less than 75°C (167°F)
  1. Thermostat
  2. Cooling system
  3. Engine coolant temperature sensor
  4. ECM

MONITOR DESCRIPTION


A082385E13

The ECM estimates the engine coolant temperature (ECT) based on engine starting temperature, engine loads and engine speed. The ECM then compares the estimated ECT with the actual ECT. When the estimated ECT reaches 75°C (167°F), the ECM checks the actual ECT. If the actual ECT is less than 75°C (167°F), the ECM will interpret this as a fault in the thermostat or the engine cooling system and set a DTC.

MONITOR STRATEGY


Related DTCs
P0128: Thermostat
Required sensors/components
Main:
Engine coolant temperature sensor, engine cooling system, thermostat
Related:
Intake air temperature sensor, vehicle speed sensor
Frequency of operation
Once per driving cycle
Duration
15 minutes
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
P0010 (VVT OCV)
P0011 (VVT system 1 - Advance)
P0012 (VVT system 1 - Retard)
P0031, P0032 (A/F sensor heater - Sensor 1)
P0100 - P0103 (MAF meter)
P0110 - P0113 (IAT sensor)
P0115 - P0118 (ECT sensor)
P0125 (Insufficient ECT for closed loop)
P0171, P0172 (Fuel system)
P0300 - P0304 (Misfire)
P0335 (CKP sensor)
P0340, P0341 (CMP sensor)
P0351-P0354 (Igniter)
P0500 (VSS)
P2196 (A/F sensor - Rationality)
P2237 (A/F sensor - Open)
P2A00 (A/F sensor - Slow response)
Battery voltage
11 V or more
Either of the following condition 1 or 2 is met
-
1. All of the following conditions are met
(a), (b) and (c)
(a) ECT at engine start - IAT at engine start
-15 to 7°C (5 to 44.6°F)
(b) ECT at engine start
-10 to 56°C (14 to 132.8°F)
(c) IAT at engine start
-10 to 56°C (14 to 132.8°F)
2. All of the following conditions are met
(d), (e) and (f)
(d) ECT at engine start - IAT at engine start
More than 7°C (44.6°F)
(e) ECT at engine start
56°C (132.8°F) or less
(f) IAT at engine start
-10°C (14°F) or more
Accumulated time that vehicle speed is 80 mph (128 km/h) or more
Less than 20 seconds

TYPICAL MALFUNCTION THRESHOLDS


Duration that both of the following conditions are met
5 seconds or more
(1) Estimated ECT
75°C (167°F) or more
(2) ECT sensor output
Less than 75°C (167°F)

COMPONENT OPERATING RANGE


Engine coolant temperature sensor output value after warm-up
75°C (167°F) or more

MONITOR RESULT

Refer to detailed information (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK COOLING SYSTEM
  1. Check that there is a defect in the cooling system which causes overcooling, such as abnormal radiator fan operation, modified cooling system and so on.

    OK:
    There is no modification of cooling system.



NG
REPAIR OR REPLACE COOLING SYSTEM
OK


2.INSPECT THERMOSTAT
  1. Check the valve opening temperature of the thermostat.

    OK:
    Thermostat valve begins to open at temperature of 80 to 84°C (176 to 183°F).

    HINT:
    Also check the valve is completely closed at a temperature lower than specified above.



NG
REPLACE THERMOSTAT
OK

REPLACE ECM