Home › BODY ELECTRICAL › DOOR LOCK › KEY REMINDER WARNING SYSTEM

KEY REMINDER WARNING SYSTEM > Key Reminder Buzzer does not Sound

for Preparation Click here


DESCRIPTION

With the power switch OFF or ON (ACC), the combination meter sounds the buzzer when it receives a buzzer request signal from the transponder key ECU using the BEAN. The transponder key ECU outputs this signal when it receives: 1) a halfway switch signal (set when the key is in the key slot); and 2) a driver side door courtesy switch signal from the multiplex network body ECU (set when the driver side door is open).

WIRING DIAGRAM


E129445E01


INSPECTION PROCEDURE

1.READ VALUE OF TECHSTREAM (DRIVER SIDE DOOR COURTESY LIGHT SWITCH)
  1. Check the Data List for proper functioning of the driver side door courtesy switch.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW
    Driver side door courtesy switch signal / ON or OFF
    ON: Driver side door is open
    OFF: Driver side door is closed
    -

    OK:
    Tester display changes correctly according to open / closed condition of door.



NG
Go to step 4
OK


2.READ VALUE OF TECHSTREAM (HALFWAY SWITCH)
  1. Check the Data List for proper functioning of the key slot.

    Transponder Key ECU  
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key SW
    Halfway switch signal / ON or OFF
    ON: Key is in key slot
    OFF: No key is in key slot
    -

OK:
ON (key is in key slot) appears on the screen.



NG
Go to step 6
OK


3.CHECK COMBINATION METER
  1. Check the warning buzzer built into the combination meter (Click here).

OK:
Warning buzzer sounds.



NG
REPLACE COMBINATION METER ASSEMBLY
OK

REPLACE DRIVER SIDE JUNCTION BLOCK (BODY ECU) 

4.INSPECT FRONT DOOR COURTESY LIGHT SWITCH LH
E114552E08
  1. Remove the courtesy light switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Condition
    Switch Condition
    Switch Condition
    1 - Body ground
    Not pushed
    Below 1 Ω
    1 - Body ground
    Pushed
    10 kΩ or higher



NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH LH
OK


5.CHECK WIRE HARNESS (COURTESY LIGHT SWITCH - BODY ECU)
B079560E03
  1. Disconnect the D7 switch connector.

  1. Disconnect the 1D junction block connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D7-1 - 1D-21 (DCTY)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE DRIVER SIDE JUNCTION BLOCK (BODY ECU) 

6.INSPECT KEY SLOT
B079242E04
  1. Remove the key slot.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Condition
    Condition
    Specified Condition
    2 (COM) - 4 (KSW1)
    Key in key slot
    Below 1 Ω
    No key in key slot
    10 kΩ or higher



NG
REPLACE KEY SLOT
OK


7.CHECK WIRE HARNESS (KEY SLOT - INSTRUMENT TRANSPONDER KEY ECU)
B080183E05
  1. Disconnect the K2 key slot connector.

  1. Disconnect the T5 ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    K2-4 (KSW1) - T5-5 (CUWS)
    Always
    Below 1 Ω
    K2-2 (COM) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE TRANSPONDER KEY ECU