Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM

AIR CONDITIONING SYSTEM > PTC Heater Circuit

for Preparation Click here


DESCRIPTION

The PTC heater is installed in the radiator in the heater unit on the driver and passenger's FOOT sides and operates when cooling water temperature is low and normal heater effectiveness is insufficient.
The air conditioning amplifier switches the circuit in the PTC relay and operates the PTC heater when the operating conditions (cooling water temperature is below 55°C (131°F), setting temperature is MAX. HOT, air outlet damper position is FOOT or FOOT / DEF and blower switch in not OFF) are met.

WIRING DIAGRAM


E125220E02


INSPECTION PROCEDURE

1.INSPECT FUSE (PS HTR, PTC HTR1, PTC HTR2, GAUGE)
  1. Remove the PS HTR H-fuse, PTC HTR1 and PTC HTR2 fuses from the engine room junction block.

  1. Remove the GAUGE fuse from the driver side junction block.

  1. Measure the resistance of the fuses.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2.INSPECT PTC HEATER RELAY (Marking: PS HTR, PTC HTR 1, PTC HTR 2)


    E127528E01
  1. Remove the PS HTR, PTC HTR 1 and PTC HTR 2 heater relays from the engine room No. 2 relay block.

  1. Measure the resistance of the relays.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (When battery voltage applied to terminals 1 and 2)



NG
REPLACE PTC HEATER RELAY
OK


3.CHECK WIRE HARNESS (AIR CONDITIONING AMPLIFIER - BATTERY)


    E127524E01
  1. Disconnect the A7 air conditioning amplifier connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A7-17 (PTC) - Body ground
    Power switch ON (IG)
    10 to 14 V
    A7-26 (HT-1) - Body ground
    Power switch ON (IG)
    10 to 14 V
    A7-25 (HT-2) - Body ground
    Power switch ON (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4.CHECK AIR CONDITIONING AMPLIFIER (PTC, HT-1, HT-2, VOLTAGE)


    I041186E13
  1. Connect the connectors.

  1. Measure the voltage of the connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A7-17 (PTC) - Body ground
    Power switch ON (READY)
    Temperature: Max. HOT
    Ventilator mode: FOOT
    Coolant temperature: 55°C (131°F) or lower
    Blower switch: OFF → LO (after 30 sec.)
    Below 1 V → 10 to 14 V
    A7-26 (HT-1) - Body ground
    Power switch ON (READY)
    Temperature: Max. HOT
    Ventilator mode: FOOT
    Coolant temperature: 55°C (131°F) or lower
    Blower switch: OFF → LO (after 30 sec.)
    Below 1 V → 10 to 14 V
    A7-25 (HT-2) - Body ground
    Power switch ON (READY)
    Temperature: Max. HOT
    Ventilator mode: FOOT
    Coolant temperature: 55°C (131°F) or lower
    Blower switch: OFF → LO (after 30 sec.)
    Below 1 V → 10 to 14 V

    HINT:
    1. PTC operation may stop when the electric load on the vehicle is high. Perform the inspection under conditions with low electric load (such as with headlights turned OFF).
    2. Since the 2 PTC heaters are gradually turned to the ON position, perform the inspection 30 seconds after the blower switch is turned to the LO position.



NG
REPLACE AIR CONDITIONING AMPLIFIER
OK


5.INSPECT PTC HEATER


    E072666E01
  1. Disconnect the connector from the PTC heater.

  1. Check the continuity between each terminal.

    Standard resistance:
    Tester Connection
    Specified Condition
    P12-1 - P12-2
    Continuity (0.5 kΩ or higher)
    P12-3 - P12-4
    Continuity (0.5 kΩ or higher)



NG
REPLACE PTC HEATER
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR