Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1411    Room Temperature Sensor Circuit

for Preparation Click here


DESCRIPTION

The room temperature sensor is installed in the instrument panel to detect the room temperature and control the heater and air conditioner "AUTO" function. The resistance of the room temperature sensor changes in accordance with the room temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.
The air conditioning amplifier applies voltage (5 V) to the room temperature sensor and reads voltage changes as the resistance of the room temperature sensor changes. This sensor also sends appropriate signals to the air conditioning amplifier. The room temperature sensor is integrated with the room humidity sensor.

DTC No.
Detection Condition
Trouble Area
B1411
Open or short in room temperature sensor circuit
  1. Room temperature sensor
  2. Wire harness between cooler room temperature sensor and air conditioning amplifier
  3. Air conditioning amplifier

WIRING DIAGRAM


E125205E01


INSPECTION PROCEDURE

1.READ VALUE OF TECHSTREAM
  1. Connect Techstream to DLC3.

  1. Turn the power switch ON (IG) and turn Techstream ON.

  1. Select the item below in the Data List, and read the display on Techstream.

    Air conditioning amplifier 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    Room Temperature Sensor
    Room temperature sensor / Open in the circuit:
    min.: -6.5°C (20.3°F)
    max.: 57.25°C (135.05°F)
    Actual room temperature is displayed
    Open in the circuit: -6.5°C (20.3°F)
    Short in the circuit: 57.25°C (135.05°F)

    OK:
    The display is as specified in the normal condition.


    Result 
    Result
    Proceed to
    NG
    A
    OK (Checking from the PROBLEM SYMPTOMS TABLE)
    B
    OK (Checking from the DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE AIR CONDITIONING AMPLIFIER
A


2.CHECK AIR CONDITIONING AMPLIFIER (TR VOLTAGE)
I041186E01
  1. Remove the air conditioning amplifier with connectors still connected.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A7-8 (TR) - A7-22 (SGTR)
    Power switch ON (IG) at 25°C (77°F)
    1.8 to 2.2 V
    A7-8 (TR) - A7-22 (SGTR)
    Power switch ON (IG) at 40°C (104°F)
    1.2 to 1.6 V

    HINT:
    As the temperature increases, the voltage decreases.

    Result 
    Result
    Proceed to
    NG
    A
    OK (Checking from the PROBLEM SYMPTOMS TABLE)
    B
    OK (Checking from the DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE AIR CONDITIONING AMPLIFIER
A


3.INSPECT ROOM TEMPERATURE SENSOR
E127529E01
  1. Remove the room temperature sensor.

  1. Measure the resistance of the sensor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (THR) - 2 (GND)
    10°C (50°F)
    3.00 to 3.73 kΩ
    1 (THR) - 2 (GND)
    15°C (59°F)
    2.45 to 2.88 kΩ
    1 (THR) - 2 (GND)
    20°C (68°F)
    1.95 to 2.30 kΩ
    1 (THR) - 2 (GND)
    25°C (77°F)
    1.60 to 1.80 kΩ
    1 (THR) - 2 (GND)
    30°C (86°F)
    1.28 to 1.47 kΩ
    1 (THR) - 2 (GND)
    35°C (95°F)
    1.00 to 1.22 kΩ
    1 (THR) - 2 (GND)
    40°C (104°F)
    0.80 to 1.00 kΩ
    1 (THR) - 2 (GND)
    45°C (113°F)
    0.65 to 0.85 kΩ
    1 (THR) - 2 (GND)
    50°C (122°F)
    0.50 to 0.70 kΩ
    1 (THR) - 2 (GND)
    55°C (131°F)
    0.44 to 0.60 kΩ
    1 (THR) - 2 (GND)
    60°C (140°F)
    0.36 to 0.50 kΩ

    NOTICE:
    1. Even slightly touching the sensor may change the resistance value. Be sure to hold the connector of the sensor.
    2. When measuring, the sensor temperature must be the same as the ambient temperature.

    HINT:
    As the temperature increases, the resistance decreases (see the graph).



NG
REPLACE ROOM TEMPERATURE SENSOR
OK


4.CHECK WIRE HARNESS (ROOM TEMPERATURE SENSOR - AIR CONDITIONING AMPLIFIER)
E125230E01
  1. Disconnect the A9 sensor connector.

  1. Disconnect the A7 amplifier connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A7-8 (TR) - A9-1 (THR)
    Below 1 Ω
    A7-22 (SGTR) - A9-2 (GND)
    Below 1 Ω
    A7-8 (TR) - Body ground
    10 kΩ or higher
    A7-22 (SGTR) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER