Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1423    Pressure Sensor Circuit

for Preparation Click here


DESCRIPTION


E113418E11

The pressure switch to detect the refrigerant pressure is located in the sight glass side of the pipe on the high-pressure side. This DTC is output when the refrigerant pressure is either significantly low (below 196 kPa (2.0 kgf/cm2, 28 psi) or significantly high (over 3,140 kPa (32.0 kgf/cm2, 455 psi). Then the pressure switch sends appropriate signals to the air conditioning amplifier. The pressure switch has built-in switches to detect high and low pressure and is turned off when either is determined to be defective. The air conditioning amplifier continuously monitors the pressure switch signal after the power switch is turned ON (IG). It stops compressor control and outputs the DTC when it detects the signal indicating that the switch is turned OFF.

DTC No.
Detection Condition
Trouble Area
B1423
When either condition below is met:
  1. Open in pressure sensor circuit.
  2. Abnormal refrigerant pressure:
    Below 196 kPa (2.0 kgf/cm2, 28 psi)
    Over 3,140 kPa (32.0 kgf/cm2, 455 psi)
  1. Pressure switch
  2. Wire harness between pressure switch and body ground
  3. Multiplex communication circuit
  4. Refrigerant pipe line
  5. Air conditioning amplifier

WIRING DIAGRAM


E125209E01


INSPECTION PROCEDURE

1.CHECK REFRIGERANT PRESSURE
  1. Set the manifold gauge.

  1. Read the manifold gauge pressure when these conditions are established.

    Test conditions:
    1. Temperature at the air inlet with the switch set at RECIRC is 30 to 35°C (86 to 95°F)
    2. Power switch ON (IG)
    3. Blower speed control switch at "HI" position
    4. Temperature control dial at "COOL" position
    5. Air conditioning switch ON
    6. Fully open doors

    Standard pressure:
    Pressure on high pressure side:
    1.37 to 1.57 MPa (13.9 to 16.0 kgf/cm2, 198 to 228 psi)

    HINT:
    If the refrigerant pressure is below 196 kPa (2.0 kgf/cm2, 28 psi), the refrigerant amount in the air conditioning cycle may have decreased significantly for reasons such as a gas leakage.



NG
INSPECT AND REPAIR AIR CONDITIONING CYCLE
OK


2.CHECK AIR CONDITIONING OPERATION
I040669E01
  1. Disconnect the P1 pressure switch connector.

  1. Connect terminals 1 and 4 of the connector of the pressure switch on the vehicle wire harness side using a service wire.

  1. Turn the power switch ON (IG).

  1. Turn the air conditioning switch ON and check that the compressor is operated.

  1. Check that the compressor is not operated when disconnecting terminals 1 and 4 (that were connected in the prior step).

    OK:
    Terminals 1 and 4 connected: the compressor is operated
    Terminals 1 and 4 disconnected: the compressor is not operated



OK
REPLACE PRESSURE SWITCH
NG


3.CHECK WIRE HARNESS (PRESSURE SWITCH - AIR CONDITIONING AMPLIFIER AND BODY GROUND)
E125232E01
  1. Disconnect the P1 pressure switch connector.

  1. Disconnect the A7 amplifier connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A7-6 (PSW) - P1-4
    Below 1 Ω
    P1-1 - Body ground
    Below 1 Ω
    A7-6 (PSW) - Body ground
    10 kΩ or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK (Checking from the PROBLEM SYMPTOMS TABLE)
    B
    OK (Checking from the DTC)
    C



A
REPAIR OR REPLACE HARNESS AND CONNECTOR

B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
C

REPLACE AIR CONDITIONING AMPLIFIER