Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1432    Air Inlet Damper Position Sensor Circuit

for Preparation Click here


DESCRIPTION

E109300E19
This sensor detects the position of the air inlet control servo motor and sends the appropriate signals to the air conditioning amplifier. The position sensor is built into the air inlet control servo motor.
The position sensor's resistance changes as the air inlet control servo motor arm moves.
It outputs voltage (5 V) that is input to terminal 3 (VZ) and terminal 3 (PT) via the variable resistor, and then to the air conditioning amplifier. The air conditioning amplifier reads the arm position with the input voltage from the position sensor.

DTC No.
Detection Condition
Trouble Area
B1432
Open or short in power source circuit in air inlet damper position sensor circuit.
  1. Air inlet control servo motor (air inlet damper position sensor)
  2. Wire harness between air inlet control servo motor and air conditioning amplifier
  3. Air conditioning amplifier

WIRING DIAGRAM


E125210E04


INSPECTION PROCEDURE

1.READ VALUE OF TECHSTREAM
  1. Connect Techstream to DLC3.

  1. Turn the power switch ON (IG) and turn Techstream ON.

  1. Select the item below in the Data List, and read the display on Techstream.

    Air conditioning amplifier 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    Air Inlet Damper Position
    Air inlet damper position /
    min.: -14% max.: 113.5%
    Damper is at "RECIRCULATION": -1.0%
    Damper is at "FRESH": 110.0%
    Damper is at "HALF-RECIRCULATION": 20.0 to 102.0%
    Open in the circuit: 50.0%
    Air Inlet Damper Target
    Air inlet damper target position /
    min.: -14% max.: 113.5%
    Damper is at "RECIRCULATION": -1.0%
    Damper is at "FRESH": 110.0%
    Damper is at "HALF-RECIRCULATION": 20.0 to 102.0%
    Open in the circuit: 50.0%

    OK:
    The displayed is as specified in the normal condition.


    Result 
    Result
    Proceed to
    NG
    A
    OK (Checking from the PROBLEM SYMPTOMS TABLE)
    B
    OK (Checking from the DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE AIR CONDITIONING AMPLIFIER
A


2.CHECK AIR CONDITIONING AMPLIFIER (TPI VOLTAGE)
I041186E06
  1. Remove the air conditioning amplifier with connectors still connected.

  1. Change the set REC / FRS to activate the air inlet servo motor.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A7-19 (TPI) - A7-4 (SGTPI)
    Power switch ON (IG)
    RECIRC position
    3.5 to 4.5 V
    A7-19 (TPI) - A7-4 (SGTPI)
    Power switch ON (IG)
    FRESH position
    0.5 to 1.8 V

    HINT:
    As the air inlet servo motor is moved from REC position to FRS position, the voltage decreases gradually without interruption.

    Result:
    Result
    Proceed to
    NG
    A
    OK (Checking from the PROBLEM SYMPTOMS TABLE)
    B
    OK (Checking from the DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE AIR CONDITIONING AMPLIFIER
A


3.INSPECT AIR INLET CONTROL SERVO MOTOR
E068754E02
  1. Remove the air inlet control servo motor.

  1. Measure the resistance of the servo motor.

    Standard resistance:
    Tester Connection
    Specified Condition
    A14-1 (VZ) - A14-2 (GND)
    4.2 to 7.8 kΩ



    E127531E01
  1. Measure the resistance of the servo motor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A14-3 (PT) - A14-2 (GND)
    RECIRCULATION position
    3.4 to 6.2 kΩ
    A14-3 (PT) - A14-2 (GND)
    FRESH position
    0.6 to 1.1 kΩ

    HINT:
    1. Refer to the operation procedure of the air inlet control servo motor .
    2. As the air inlet control servo motor moves from FRESH position to RECIRCULATION position, the resistance decreases gradually without interruption.



NG
REPLACE AIR INLET CONTROL SERVO MOTOR
OK


4.CHECK WIRE HARNESS (AIR INLET CONTROL SERVO MOTOR - AIR CONDITIONING AMPLIFIER)
E125233E05
  1. Disconnect the A14 servo connector.

  1. Disconnect the A7 amplifier connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A7-19 (TPI) - A14-3 (PT)
    Below 1 Ω
    A7-4 (SGTPI) - A14-2 (GND)
    Below 1 Ω
    A7-3 (S5TPI) - A14-1 (VZ)
    Below 1 Ω
    A7-19 (TPI) - Body ground
    10 kΩ or higher
    A7-4 (SGTPI) - Body ground
    10 kΩ or higher
    A7-3 (S5TPI) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER