Control
| Outline
|
Fuzzy Control
| The fuzzy control determines the conformity levels of the temperature deviation, ambient temperature, and solar radiation by defining their respective mathematical functions. In addition, a fuzzy calculation method is used to calculate the required outlet air temperature (TAO) and the blower volume. Based on these calculations, the air conditioning amplifier effects the respective controls for the outlet air temperature, blower volume, compressor, and air outlet.
|
Outlet Air Temp. Control
| Air Mix Damper Control
| In response to the temperature control switch setting, the required outlet air temperature, evaporator temperature sensor, and engine coolant temperature sensor compensations are used by the air mix control damper control to calculate a tentative damper opening angle, through an arithmetic circuit in the air mix damper, to arrive at a target damper opening angle.
|
Blower Control
| Blower Motor Start Up Control
| When the blower motor is started up, the air conditioning amplifier transmits a blower motor actuation signal with a low duty cycle ratio to the blower pulse controller, which applies a low voltage to the blower motor, in order to operate the blower motor for 3 seconds at a low speed. This is designed to protect the blower pulse controller from a sudden start-up voltage surge.
|
Manual Control
| Sets the blower speed according to operation of the blower switch.
|
Automatic Control
| Step Less Air Volume Control:
- When the AUTO switch located on the steering pad switch is pushed, or the air conditioning screen display of the multi-display is touched, the air conditioning amplifier automatically regulates the duty ratio to the blower pulse controller in accordance with a calculation result by the fuzzy control in order to deliver step less air volume.
Warm-up Control:
- When the air outlet is in the FOOT, BI-LEVEL, or FOOT/DEF mode, the blower will not operate until the engine coolant temperature increases above a prescribed value. When the temperature increases above a prescribed value, the blower motor operates at the LO speed.
Time-Lagged Air Flow Control:
- 2 types of time-lagged air flow control (in accordance with the detected by the evaporator temperature sensor) help prevent hot air from being emitted from FACE or BI-LEVEL vent.
Sunlight Air Flow Control:
- Controls the blower speed in accordance with the intensity of the sunlight when the air outlet mode is at FACE or BI-LEVEL. The blower speed can be adjusted in response to the signal received from the solar sensor.
|
Air Outlet Control
| Manual Control
| Changes the air outlet in accordance with the selected position of the mode select switch.
|
Automatic Control
| Mode Damper Switching Servo motor Control:
- When the AUTO switch is pushed, automatic control causes the mode servo motor to rotate to a desired position in accordance with the target damper opening, which is based on the calculation of the TAO.
Low-Temperature FOOT/DEF Control:
- In accordance with the engine coolant temperature, ambient temperature, amount of sunlight, required outlet temperature (TAO), and vehicle speed conditions, this control automatically switches the blower outlet between the FOOT / DEF modes to prevent the window from becoming fogged when the outside air temperature is low.
|
Air Inlet Control
| Manual Control
| Drives the air inlet servo motor according to the operation of the air inlet control switch and fixes the dampers in the FRESH or RECIRC position.
|
Automatic Control
| Automatic RECIRC / FRESH Control:
- When the AUTO switch is pressed, the system controls the servo motor so that the air inlet is as calculated in accordance with the TAO.
DEF Mode Control:
- When switching the mode switching switch to DEF mode, air conditioning amplifier turns MAX mode ON forcibly and switched to FRESH mode.
- When switching the mode switching switch to FOOT / DEF mode, air conditioning amplifier switches to FRESH mode.
|
2-Way Flow Mode Control
| At the time of selecting FRESH mode, the air conditioning amplifier will judge it as 2-way flow mode when the blower outlet is set to FOOT or FOOT / DEF, the tentative air mix damper opening angle is above the specified value (MAX HOT), and either the blower volume is more than the specified volume or the vehicle speed is less than the specified speed.
|
Half Inlet Air Mode Control
| At the time of selecting FRESH mode, the air conditioning amplifier will judge it as half inlet air mode when the blower outlet mode is set to FACE or BI-LEVEL and TAO is more than the specified temperature, and operates both outlet air introduction and inlet air circulation at the same time.
|
Electric Inverter Compressor Control
| Compressor Speed Control
| - The air conditioning amplifier calculates target speed of the compressor based on the target evaporator temperature (which is calculated by the room temperature sensor, humidity sensor, ambient temperature sensor, and the solar sensor) and the actual evaporator temperature that is detected by the evaporator temperature sensor in order to control the compressor speed.
- The air conditioning amplifier calculates the target evaporator temperature, which includes corrections based on the vehicle interior humidity (which is obtained from the humidity sensor) and the windshield glass inner surface humidity (which is calculated from the humidity sensor, solar sensor, room temperature sensor, mode damper position, and wiper operation condition). Accordingly, the air conditioning amplifier controls the compressor speed to an extent that would not inhibit the proper cooling performance or defogging performance.
|
Electrical Water Pump Control
| The electrical water pump is used in order to ensure the proper heater performance while the blower motor is ON and the engine is stopped.
|
Engine Start Request Control
| To ensure the proper heater performance when the hybrid system is started at low temperatures, the air conditioning amplifier transmits an engine start request to the hybrid control ECU in accordance with the TAO, engine coolant temperature sensor signal, and ambient temperature sensor signal.
|
PTC Heater Control
| When the hybrid system is operating (READY) and the blower motor is turned ON, the air conditioning amplifier turns on the PTC heater if the conditions listed below are met. Heater core integrated PTC heater
- Air outlet is in the FOOT, FOOT / DEF or DEF mode.
- Engine coolant temperature is below specified temperature.
- Ambient temperature is below specified temperature (DEF mode).
- Tentative air mix damper opening angle is above the specified value (MAX HOT).
Footwell air duct integrated PTC heater
- Air outlet is in the FOOT or FOOT / DEF mode.
- Engine coolant temperature is below specified temperature.
- Tentative air mix damper opening angle is above the specified value (MAX HOT).
|
Electric Cooling Fan Control
| The air conditioning amplifier control the cooling fan in accordance with the vehicle speed signal and compressor speed signal.
|
Rear Window Defogger Control
| Switches the rear defogger and outside rear view mirror heaters on for 15 minutes when the rear defogger switch is switched on. Switches them off if the switch is pressed while they are operating.
|
Outer Temperature Indication Control
| Based on the signals from the ambient temperature sensor, this control calculates the outside temperature, which is then corrected in the air conditioning ECU, and shown in the multi-display.
|
Self-Diagnosis
| Checks the sensor and A/C inverter in accordance with operation of the air conditioning switches, then the heater control panel displays a DTC (Diagnosis Trouble Code) to indicate if there is a malfunction or not (sensor check function).
|
Drives the actuators through a predetermined sequence in accordance with the operation of the air conditioning switches (actuator check function).
|
Function of main damper
Control Damper
| Control Position
| Damper Position
| Operation
|
Air Inlet Control Damper
| C or I
|  Indicator OFF
| 1, 3
| Brings in fresh air.
|
2, 4
| Brings in fresh air while circulating internal air.
|
C or I
|  Indicator ON
| 2, 4
| Recirculates internal air.
|
Air Mix Control Damper
| A, B or K, L
| -
| 5, 8 to 6, 9 to 7, 10
| Varies mixture ratio of fresh air and recirculation air in order to regulate temperature continuously from HOT to COOL.
|
Mode Control Damper
| E
|  FACE
| 14, 15, 21, 22 (14, 16, 21, 22)*2
| Air blows out of center registers and side registers.
|
F
|  BI-LEVEL
| 14, 17, 20, 22
| Air mainly blows out of center registers, side registers, and footwell register ducts.
|
G
|  FOOT
| 13, 18, 19, 22 (12, 17, 19, 23)*1
| Air mainly blows out of front and rear footwell register ducts. In addition, air blows out slightly from front and side defrosters, and side registers.
|
H
|  FOOT/DEF
| 12, 17, 19, 22 (11, 15, 19, 23)*1
| Air mainly blows out of front and side defrosters to defrost windshield. Air also blows out from front and rear footwell register ducts, and side registers.
|
D or J
|  DEF
| 12, 17, 19, 22
| Air blows out of front and side defrosters and side registers to defrost windshield.
|