Home › SUSPENSION & AXLE › SUSPENSION › FRONT STABILIZER BAR

FRONT STABILIZER BAR > REMOVAL

for Preparation Click here



1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


2. REMOVE COLUMN HOLE COVER SILENCER SHEET


G028397E01
  1. Fold back the floor carpet and remove the 2 clips and column hole cover silencer sheet.



3. DISCONNECT STEERING SLIDING YOKE SUB-ASSEMBLY


    G029446E06
  1. Fix the steering wheel with the seat belt in order to prevent rotation and damage to the spiral cable.



    G029896E03
  1. Put matchmarks in the sliding yoke and intermediate shaft.

  1. Loosen the bolt labeled A and remove the bolt labeled B to separate the sliding yoke.



4. DISCONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    G028294E02
  1. Remove the clip labeled A and disconnect the hole cover from the body.

    NOTICE:
    Do not damage the clip labeled B.



5. REMOVE FRONT WHEEL


6. REMOVE FRONT STABILIZER LINK ASSEMBLY LH


    C080890E01
  1. Remove the 2 nuts and front stabilizer link LH.

    HINT:
    Use a 6 mm hexagon wrench to hold the stud if the ball joint turns together with the nut.



7. DISCONNECT NO. 2 TIE ROD END SUB-ASSEMBLY


    F047429E01
  1. Remove the clip and castle nut.

  1. Using SST, disconnect the tie rod end from the steering knuckle.

    SST
    09628-00011  

    NOTICE:
    1. Do not damage the front disc brake dust cover.
    2. Be sure to hang the tie rod end with a string to prevent SST from dropping.
    3. Do not damage the ball joint dust cover.
    4. Do not damage the steering knuckle.
    5. Securely hang SST to the spacer of the steering knuckle.
    6. Replace the steering knuckle with a new one if the spacer comes off the steering knuckle.



8. DISCONNECT NO. 1 TIE ROD END SUB-ASSEMBLY

HINT:
Use the same procedure described for the No. 2 tie rod end.



9. REMOVE FLOOR PANEL BRACE FRONT


    A086201
  1. Remove the 2 bolts and floor panel brace.



10. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.

  1. Remove the front exhaust pipe from the 2 exhaust pipe supports.



  1. Remove the gasket from the exhaust manifold.


    A086203



11. DISCONNECT FRONT NO. 1 STABILIZER BRACKET LH
  1. Remove the 2 bolts and the No. 1 stabilizer bracket from the front suspension crossmember.



12. DISCONNECT FRONT NO. 1 STABILIZER BRACKET RH

HINT:
Remove the RH side following the same procedures as the LH side.



13. REMOVE STEERING INTERMEDIATE SHAFT


    G028290E03
  1. Move the No. 1 column hole cover to the upper side of the vehicle and put matchmarks on the intermediate shaft and steering gear.

    NOTICE:
    Do not damage the No. 1 hole cover when moving it.

  1. Remove the bolt and remove the intermediate shaft from the inside of the vehicle.

  1. Remove the No. 1 column hole cover from the steering gear.

    NOTICE:
    Do not damage the No. 1 hole cover clip.



14. REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


15. REMOVE STEERING GEAR ASSEMBLY


    G028292E04
  1. Remove the 4 bolts and steering gear from the left side of the vehicle.

    HINT:
    Be careful not to hit the stabilizer bar when removing the steering gear.



16. REMOVE FRONT NO. 1 STABILIZER BAR BUSH
  1. Remove the 2 front No. 1 stabilizer bar bushes from the stabilizer bar.



17. REMOVE FRONT STABILIZER BAR
  1. Remove the front stabilizer bar from the right side of the vehicle.