Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Short in CAN Bus Lines

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
  1. Short between CAN bus lines
  2. Hybrid vehicle control ECU
  3. Battery ECU
  4. ECM
  5. Skid control ECU
  6. Steering angle sensor
  7. Yaw rate sensor
  8. Power steering ECU
  9. Gateway ECU
  10. J/C1 (Junction connector)
  11. J/C2 (Junction connector)

WIRING DIAGRAM


C126185E06


INSPECTION PROCEDURE

1.CHECK CAN BUS LINES FOR SHORT CIRCUIT (DLC3 BRANCH WIRE)


    H100769E13
  1. Disconnect the J15 J/C1 connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    Power switch OFF
    1 MΩ or more



NG
REPLACE DLC3 BRANCH WIRE AND CONNECTOR (CANH, CANL)
OK


2.CONNECT CONNECTOR
  1. Reconnect the J15 J/C1 connector.


NEXT


3.CHECK CAN BUS LINES FOR SHORT CIRCUIT (CAN BUSES TO J/C2)


    H100769E13
  1. Disconnect the J18 J/C2 connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    Power switch OFF
    108 to 132 Ω



OK
Go to step 17
NG


4.CHECK CAN BUS LINES FOR SHORT CIRCUIT (J/C1 - J/C2)


    C127797E01
  1. Disconnect the J15 J/C1 connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J15-17 (CANH) - J15-6 (CANL)
    Power switch OFF
    1 MΩ or more

    HINT:
    Measure the resistance with the J18 J/C2 connector disconnected.



NG
REPLACE CAN MAIN WIRE AND CONNECTOR (J/C1 - J/C2)
OK


5.CONNECT CONNECTOR
  1. Reconnect the J15 J/C1 connector and J18 J/C2 connector.


NEXT


6.CHECK CAN BUS LINES FOR SHORT CIRCUIT (BATTERY ECU)


    H100769E13
  1. Disconnect the B11 battery ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    Power switch OFF
    108 to 132 Ω



OK
REPLACE BATTERY ECU
NG


7.CHECK CAN BUS LINES FOR SHORT CIRCUIT (BATTERY ECU - J/C1)


    C126181E03
  1. Disconnect the J15 J/C1 connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B11-18 (CANH) - B11-19 (CANL)
    Power switch OFF
    1 MΩ or more

    HINT:
    Measure the resistance with the B11 battery ECU connector disconnected.



NG
REPLACE CAN MAIN WIRE AND CONNECTOR (BATTERY ECU - J/C1)
OK


8.CONNECT CONNECTOR
  1. Reconnect the B11 battery ECU connector and J15 J/C1 connector.


NEXT


9.CHECK CAN BUS LINES FOR SHORT CIRCUIT (POWER STEERING ECU)


    H100769E13
  1. Disconnect the P8 power steering ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    Power switch OFF
    54 to 69 Ω



OK
REPLACE POWER STEERING ECU
NG


10.CHECK CAN BUS LINES FOR SHORT CIRCUIT (POWER STEERING ECU BRANCH WIRE)


    C126173E01
  1. Disconnect the J15 J/C1 connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    P8-1 (CANH) - P8-7 (CANL)
    Power switch OFF
    1 MΩ or more

    HINT:
    Measure the resistance with the P8 power steering ECU connector disconnected.



NG
REPLACE POWER STEERING ECU BRANCH WIRE AND CONNECTOR (CANH, CANL)
OK


11.CONNECT CONNECTOR
  1. Reconnect the P8 power steering ECU connector and J15 J/C1 connector.


NEXT


12.CHECK CAN BUS LINES FOR SHORT CIRCUIT (STEERING ANGLE SENSOR)

NOTICE:
For vehicles without enhanced VSC, go to "CHECK CAN BUS LINES FOR SHORT CIRCUIT (SKID CONTROL ECU)".



    H100769E13
  1. Disconnect the S13 steering angle sensor connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    Power switch OFF
    54 to 69 Ω



OK
REPLACE STEERING ANGLE SENSOR
NG


13.CHECK CAN BUS LINES FOR SHORT CIRCUIT (STEERING ANGLE SENSOR BRANCH WIRE)


    C126177E01
  1. Disconnect the J15 J/C1 connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S13-10 (CANH) - S13-9 (CANL)
    Power switch OFF
    1 MΩ or more

    HINT:
    Measure the resistance with the S13 steering angle sensor connector disconnected.



NG
REPLACE STEERING ANGLE SENSOR BRANCH WIRE AND CONNECTOR (CANH, CANL)
OK


14.CONNECT CONNECTOR
  1. Reconnect the S13 steering angle sensor connector and J15 J/C1 connector.


NEXT


15.CHECK CAN BUS LINES FOR SHORT CIRCUIT (SKID CONTROL ECU)


    H100769E13
  1. Disconnect the S8 skid control ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    Power switch OFF
    54 to 69 Ω



OK
REPLACE SKID CONTROL ECU
NG


16.CHECK CAN BUS LINES FOR SHORT CIRCUIT (SKID CONTROL ECU BRANCH WIRE)


    C126171E04
  1. Disconnect the J15 J/C1 connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S8-19 (CANH) - S8-18 (CANL)
    Power switch OFF
    1 MΩ or more

    HINT:
    Measure the resistance with the S8 skid control ECU connector disconnected.



NG
REPLACE SKID CONTROL ECU BRANCH WIRE AND CONNECTOR
OK

REPLACE JUNCTION CONNECTOR (J/C1) 

17.CONNECT CONNECTOR
  1. Reconnect the J18 J/C2 connector.


NEXT


18.CHECK CAN BUS LINES FOR SHORT CIRCUIT (ECM)


    H100769E13
  1. Disconnect the E6 ECM connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    Power switch OFF
    108 to 132 Ω



OK
REPLACE ECM
NG


19.CHECK CAN BUS LINES FOR SHORT CIRCUIT (ECM - J/C2)


    C127794E03
  1. Disconnect the J18 J/C2 connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-31 (CANH) - E6-30 (CANL)
    Power switch OFF
    1 MΩ or more

    HINT:
    Measure the resistance with the E6 ECM connector disconnected.



NG
REPLACE CAN MAIN WIRE AND CONNECTOR (ECM - J/C2)
OK


20.CONNECT CONNECTOR
  1. Reconnect the E6 ECM connector and J18 J/C2 connector.


NEXT


21.CHECK CAN BUS LINES FOR SHORT CIRCUIT (YAW RATE SENSOR)

NOTICE:
For vehicles without enhanced VSC, go to "CHECK CAN BUS LINES FOR SHORT CIRCUIT (HYBRID VEHICLE CONTROL ECU)".



    H100769E13
  1. Disconnect the Y1 yaw rate sensor connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    Power switch OFF
    54 to 69 Ω



OK
REPLACE YAW RATE SENSOR
NG


22.CHECK CAN BUS LINES FOR SHORT CIRCUIT (YAW RATE SENSOR BRANCH WIRE)


    F100900E01
  1. Disconnect the J18 J/C2 connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Y1-3 (CANH) - Y1-2 (CANL)
    Power switch OFF
    1 MΩ or more

    HINT:
    Measure the resistance with the Y1 yaw rate sensor connector disconnected.



NG
REPLACE YAW RATE SENSOR BRANCH WIRE AND CONNECTOR (CANH, CANL)
OK


23.CONNECT CONNECTOR
  1. Reconnect the Y1 yaw rate sensor connector and J18 J/C2 connector.


NEXT


24.CHECK CAN BUS LINES FOR SHORT CIRCUIT (HYBRID VEHICLE CONTROL ECU)


    H100769E13
  1. Disconnect the H14 hybrid vehicle control ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    Power switch OFF
    54 to 69 Ω



OK
REPLACE HYBRID VEHICLE CONTROL ECU
NG


25.CHECK CAN BUS LINES FOR SHORT CIRCUIT (HYBRID VEHICLE CONTROL ECU BRANCH WIRE)


    C126168E01
  1. Disconnect the J18 J/C2 connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    H14-8 (CANH) - H14-9 (CANL)
    Power switch OFF
    1 MΩ or more

    HINT:
    Measure the resistance with the H14 hybrid vehicle control ECU connector disconnected.



NG
REPLACE HYBRID VEHICLE CONTROL ECU BRANCH WIRE AND CONNECTOR (CANH, CANL)
OK


26.CONNECT CONNECTOR
  1. Reconnect the H14 hybrid vehicle control ECU connector and J18 J/C2 connector.


NEXT


27.CHECK CAN BUS LINES FOR SHORT CIRCUIT (GATEWAY ECU)


    H100769E13
  1. Disconnect the G1 gateway ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    Power switch OFF
    54 to 69 Ω



OK
REPLACE GATEWAY ECU
NG


28.CHECK CAN BUS LINES FOR SHORT CIRCUIT (GATEWAY ECU BRANCH WIRE)


    C126176E03
  1. Disconnect the J18 J/C2 connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    G1-17 (CA1H) - G1-18 (CA1L)
    Power switch OFF
    1 MΩ or more

    HINT:
    Measure the resistance with the G1 gateway ECU connector disconnected.



NG
REPLACE GATEWAY ECU BRANCH WIRE AND CONNECTOR (CA1H, CA1L)
OK

REPLACE JUNCTION CONNECTOR (J/C2)