CAN COMMUNICATION SYSTEM > Short to B+ in CAN Bus Line |
| Symptom | Trouble Area |
| There is resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3. |
|

| 1.CHECK CAN BUS LINE FOR SHORT TO +B (DLC3 BRANCH WIRE) |
![]() |
Disconnect the J15 J/C1 connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
| D1-6 (CANH) - D1-16 (BAT) | Power switch OFF | 1 MΩ or more |
| D1-14 (CANL) - D1-16 (BAT) | Power switch OFF | 1 MΩ or more |
|
| ||||
| OK | |
| 2.CONNECT CONNECTOR |
Reconnect the J15 J/C1 connector.
| NEXT | |
| 3.CHECK CAN BUS LINE FOR SHORT TO +B (CAN BUSES TO J/C2) |
![]() |
Disconnect the J18 J/C2 connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
| D1-6 (CANH) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
| D1-14 (CANL) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
|
| ||||
| NG | |
| 4.CONNECT CONNECTOR |
Reconnect the J18 J/C2 connector.
| NEXT | |
| 5.CHECK CAN BUS LINE FOR SHORT TO +B (BATTERY ECU) |
![]() |
Disconnect the B11 battery ECU connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
| D1-6 (CANH) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
| D1-14 (CANL) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
|
| ||||
| NG | |
| 6.CHECK CAN BUS LINE FOR SHORT TO +B (BATTERY ECU - J/C1) |
![]() |
Disconnect the J15 J/C1 connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
| B11-18 (CANH) - D1-16 (BAT) | Power switch OFF | 1 MΩ or more |
| B11-19 (CANL) - D1-16 (BAT) | Power switch OFF | 1 MΩ or more |
|
| ||||
| OK | |
| 7.CONNECT CONNECTOR |
Reconnect the B11 battery ECU connector and J15 J/C1 connector.
| NEXT | |
| 8.CHECK CAN BUS LINE FOR SHORT TO +B (POWER STEERING ECU) |
![]() |
Disconnect the P8 power steering ECU connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
| D1-6 (CANH) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
| D1-14 (CANL) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
|
| ||||
| NG | |
| 9.CHECK CAN BUS LINE FOR SHORT TO +B (POWER STEERING ECU BRANCH WIRE) |
![]() |
Disconnect the J15 J/C1 connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
| P8-1 (CANH) - P7-1 (PIG) | Power switch OFF | 1 MΩ or more |
| P8-1 (CANL) - P7-1 (PIG) | Power switch OFF | 1 MΩ or more |
|
| ||||
| OK | |
| 10.CONNECT CONNECTOR |
Reconnect the P8 power steering ECU and J15 J/C1 connector.
| NEXT | |
| 11.CHECK CAN BUS LINE FOR SHORT TO +B (STEERING ANGLE SENSOR) |
![]() |
Disconnect the S13 steering angle sensor connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
| D1-6 (CANH) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
| D1-14 (CANL) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
|
| ||||
| NG | |
| 12.CHECK CAN BUS LINE FOR SHORT TO +B (STEERING ANGLE SENSOR BRANCH WIRE) |
![]() |
Disconnect the J15 J/C1 connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
| S13-10 (CANH) - S13-3 (BAT) | Power switch OFF | 1 MΩ or more |
| S13-9 (CANL) - S13-3 (BAT) | Power switch OFF | 1 MΩ or more |
|
| ||||
| OK | |
| 13.CONNECT CONNECTOR |
Reconnect the S13 steering angle sensor connector and J15 J/C1 connector.
| NEXT | |
| 14.CHECK CAN BUS LINE FOR SHORT TO +B (SKID CONTROL ECU) |
![]() |
Disconnect the A8 skid control ECU connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
| D1-6 (CANH) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
| D1-14 (CANL) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
|
| ||||
| NG | |
| 15.CHECK CAN BUS LINE FOR SHORT TO +B (SKID CONTROL ECU BRANCH WIRE) |
![]() |
Disconnect the J15 J/C1 connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
| S8-19 (CANH) - S8-3 (+BI1) | Power switch OFF | 1 MΩ or more |
| S8-19 (CANH) - S9-5 (+BI2) | ||
| S8-18 (CANL) - S8-3 (+BI1) | Power switch OFF | 1 MΩ or more |
| S8-18 (CANL) - S9-5 (+BI2) |
|
| ||||
| OK | ||
| ||
| 16.CONNECT CONNECTOR |
Reconnect the J18 J/C2 connector.
| NEXT | |
| 17.CHECK CAN BUS LINE FOR SHORT TO +B (ECM) |
![]() |
Disconnect the E6 ECM connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
| D1-6 (CANH) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
| D1-14 (CANL) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
|
| ||||
| NG | |
| 18.CHECK CAN BUS LINE FOR SHORT TO +B (ECM - J/C2) |
![]() |
Disconnect the J18 J/C2 connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
| E6-31 (CANH) - E7-6 (BATT) | Power switch OFF | 1 MΩ or more |
| E6-30 (CANL) - E7-6 (BATT) | Power switch OFF | 1 MΩ or more |
|
| ||||
| OK | |
| 19.CONNECT CONNECTOR |
Reconnect the E6 ECM connector and J18 J/C2 connector.
| NEXT | |
| 20.CHECK CAN BUS LINE FOR SHORT TO +B (YAW RATE SENSOR) |
![]() |
Disconnect the Y1 yaw rate sensor connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
| D1-6 (CANH) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
| D1-14 (CANL) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
|
| ||||
| NG | |
| 21.CHECK CAN BUS LINE FOR SHORT TO +B (YAW RATE SENSOR BRANCH WIRE) |
![]() |
Disconnect the J18 J/C2 connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
| Y1-3 (CANH) - D1-16 (BAT) | Power switch OFF | 1 MΩ or more |
| Y1-2 (CANL) - D1-16 (BAT) | Power switch OFF | 1 MΩ or more |
|
| ||||
| OK | |
| 22.CONNECT CONNECTOR |
Reconnect the Y1 yaw rate sensor connector and J18 J/C2 connector.
| NEXT | |
| 23.CHECK CAN BUS LINE FOR SHORT TO +B (HYBRID VEHICLE CONTROL ECU) |
![]() |
Disconnect the H14 hybrid vehicle control ECU connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
| D1-6 (CANH) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
| D1-14 (CANL) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
|
| ||||
| NG | |
| 24.CHECK CAN BUS LINE FOR SHORT TO +B (HYBRID VEHICLE CONTROL ECU BRANCH WIRE) |
![]() |
Disconnect the J18 J/C2 connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
| H14-8 (CANH) - H15-6 (BATT) | Power switch OFF | 1 MΩ or more |
| H14-9 (CANL) - H15-6 (BATT) | Power switch OFF | 1 MΩ or more |
|
| ||||
| OK | |
| 25.CONNECT CONNECTOR |
Reconnect the H14 hybrid vehicle control ECU connector and J18 J/C2 connector.
| NEXT | |
| 26.CHECK CAN BUS LINE FOR SHORT TO +B (GATEWAY ECU) |
![]() |
Disconnect the G1 gateway ECU connector.
Measure the resistance of the DLC3.
| Tester Connection | Condition | Specified Condition |
| D1-6 (CANH) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
| D1-14 (CANL) - D1-16 (BAT) | Power switch OFF | 6 kΩ or more |
|
| ||||
| NG | ||
| ||