Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Short to GND in CAN Bus Line

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus line and GND when there is resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3.

Symptom
Trouble Area
There is resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3.
  1. Short to GND
  2. Hybrid vehicle control ECU
  3. Battery ECU
  4. ECM
  5. Skid control ECU
  6. Steering angle sensor
  7. Yaw rate sensor
  8. Power steering ECU

WIRING DIAGRAM


C155085E01


C126190E06


INSPECTION PROCEDURE

1.CHECK CAN BUS LINE FOR SHORT TO GND (DLC3 BRANCH WIRE)


    H100769E15
  1. Disconnect the J15 J/C1 connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-4 (CG)
    Power switch OFF
    1 MΩ or more
    D1-14 (CANL) - D1-4 (CG)
    Power switch OFF
    1 MΩ or more



NG
REPLACE DLC3 BRANCH WIRE AND CONNECTOR (CANH, CANL)
OK


2.CONNECT CONNECTOR
  1. Reconnect the J15 J/C1 connector.


NEXT


3.CHECK CAN BUS LINE FOR SHORT TO GND (CAN BUSES TO J/C2)


    H100769E15
  1. Disconnect the J18 J/C2 connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-4 (CG)
    Power switch OFF
    200 Ω or more
    D1-14 (CANL) - D1-4 (CG)
    Power switch OFF
    200 Ω or more



OK
Go to step 16
NG


4.CONNECT CONNECTOR
  1. Reconnect the J18 J/C2 connector.


NEXT


5.CHECK CAN BUS LINE FOR SHORT TO GND (BATTERY ECU)


    H100769E15
  1. Disconnect the B11 battery ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-4 (CG)
    Power switch OFF
    200 Ω or more
    D1-14 (CANL) - D1-4 (CG)
    Power switch OFF
    200 Ω or more



OK
REPLACE BATTERY ECU
NG


6.CHECK CAN BUS LINE FOR SHORT TO GND (BATTERY ECU - J/C1)


    C126181E02
  1. Disconnect the J15 J/C1 connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B11-18 (CANH) - B11-12 (GND)
    Power switch OFF
    1 MΩ or more
    B11-19 (CANL) - B11-12 (GND)
    Power switch OFF
    1 MΩ or more

    HINT:
    Measure the resistance with the B11 battery ECU connector disconnected.



NG
REPLACE CAN MAIN WIRE AND CONNECTOR (BATTERY ECU - J/C1)
OK


7.CONNECT CONNECTOR
  1. Reconnect the B11 battery ECU connector and J15 J/C1 connector.


NEXT


8.CHECK CAN BUS LINE FOR SHORT TO GND (POWER STEERING ECU)


    H100769E15
  1. Disconnect the P8 power steering ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-4 (CG)
    Power switch OFF
    200 Ω or more
    D1-14 (CANL) - D1-4 (CG)
    Power switch OFF
    200 Ω or more



OK
REPLACE POWER STEERING ECU
NG


9.CHECK CAN BUS LINE FOR SHORT TO GND (POWER STEERING ECU BRANCH WIRE)


    C126173E03
  1. Disconnect the J15 J/C1 connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    P8-1 (CANH) - P7-2 (PGND)
    Power switch OFF
    1 MΩ or more
    P8-7 (CANL) - P7-2 (PGND)
    Power switch OFF
    1 MΩ or more

    HINT:
    Measure the resistance with the P8 power steering ECU connector disconnected.



NG
REPLACE POWER STEERING ECU BRANCH WIRE AND CONNECTOR (CANH, CANL)
OK


10.CONNECT CONNECTOR
  1. Reconnect the P8 power steering ECU connector and J15 J/C1 connector.


NEXT


11.CHECK CAN BUS LINE FOR SHORT TO GND (STEERING ANGLE SENSOR)

NOTICE:
For vehicles without enhanced VSC, go to "CHECK CAN BUS LINE FOR SHORT TO GND (SKID CONTROL ECU)".



    H100769E15
  1. Disconnect the S13 steering angle sensor connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-4 (CG)
    Power switch OFF
    200 Ω or more
    D1-14 (CANL) - D1-4 (CG)
    Power switch OFF
    200 Ω or more



OK
REPLACE STEERING ANGLE SENSOR
NG


12.CHECK CAN BUS LINE FOR SHORT TO GND (STEERING ANGLE SENSOR BRANCH WIRE)


    C126177E04
  1. Disconnect the J15 J/C1 connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S13-10 (CANH) - S13-2 (ESS)
    Power switch OFF
    1 MΩ or more
    S13-9 (CANL) - S13-2 (ESS)
    Power switch OFF
    1 MΩ or more

    HINT:
    Measure the resistance with the S13 steering angle sensor connector disconnected.



NG
REPLACE STEERING ANGLE SENSOR BRANCH WIRE AND CONNECTOR (CANH, CANL)
OK


13.CONNECT CONNECTOR
  1. Reconnect the S13 steering angle sensor connector and J15 J/C1 connector.


NEXT


14.CHECK CAN BUS LINE FOR SHORT TO GND (SKID CONTROL ECU)


    H100769E15
  1. Disconnect the S8 skid control ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-4 (CG)
    Power switch OFF
    200 Ω or more
    D1-14 (CANL) - D1-4 (CG)
    Power switch OFF
    200 Ω or more



OK
REPLACE SKID CONTROL ECU
NG


15.CHECK CAN BUS LINE FOR SHORT TO GND (SKID CONTROL ECU BRANCH WIRE)


    C126171E03
  1. Disconnect the J15 J/C1 connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S8-19 (CANH) - S7-1 (GND)
    Power switch OFF
    1 MΩ or more
    S8-19 (CANH) - S8-2 (GND2)
    S8-19 (CANH) - S8-1 (GND3)
    S8-19 (CANH) - S9-2 (GND4)
    S8-19 (CANH) - S9-1 (GND5)
    S8-19 (CANH) - S10-4 (GND6)
    S8-18 (CANL) - S7-1 (GND)
    Power switch OFF
    1 MΩ or more
    S8-18 (CANL) - S8-2 (GND2)
    S8-18 (CANL) - S8-1 (GND3)
    S8-18 (CANL) - S9-2 (GND4)
    S8-18 (CANL) - S9-1 (GND5)
    S8-18 (CANL) - S10-4 (GND6)

    HINT:
    Measure the resistance with the S8 skid control ECU connector disconnected.



NG
REPLACE SKID CONTROL ECU BRANCH WIRE AND CONNECTOR (CANH, CANL)
OK

REPLACE CAN MAIN WIRE AND CONNECTOR (J/C1 - J/C2) 

16.CONNECT CONNECTOR
  1. Reconnect the J18 J/C2 connector.


NEXT


17.CHECK CAN BUS LINE FOR SHORT TO GND (ECM)


    H100769E15
  1. Disconnect the E6 ECM connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-4 (CG)
    Power switch OFF
    200 Ω or more
    D1-14 (CANL) - D1-4 (CG)
    Power switch OFF
    200 Ω or more



OK
REPLACE ECM
NG


18.CHECK CAN BUS LINE FOR SHORT TO GND (ECM - J/C2)


    C127794E04
  1. Disconnect the J18 J/C2 connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-31 (CANH) - E4-7 (E01)
    Power switch OFF
    1 MΩ or more
    E6-31 (CANH) - E4-6 (E02)
    E6-31 (CANH) - E6-7 (E03)
    E6-31 (CANH) - E4-1 (E04)
    E6-31 (CANH) - E5-3 (ME01)
    E6-30 (CANL) - E4-7 (E01)
    Power switch OFF
    1 MΩ or more
    E6-30 (CANL) - E4-6 (E02)
    E6-30 (CANL) - E6-7 (E03)
    E6-30 (CANL) - E4-1 (E04)
    E6-30 (CANL) - E5-3 (ME01)

    HINT:
    Measure the resistance with the E6 ECM connector disconnected.



NG
REPLACE CAN MAIN WIRE AND CONNECTOR (ECM - J/C2)
OK


19.CONNECT CONNECTOR
  1. Reconnect the E6 ECM connector and J18 J/C2 connector.


NEXT


20.CHECK CAN BUS LINE FOR SHORT TO GND (YAW RATE SENSOR)

NOTICE:
For vehicles without enhanced VSC, go to "CHECK CAN BUS LINE FOR SHORT TO GND (HYBRID VEHICLE CONTROL ECU)".



    H100769E15
  1. Disconnect the Y1 yaw rate sensor connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-4 (CG)
    Power switch OFF
    200 Ω or more
    D1-14 (CANL) - D1-4 (CG)
    Power switch OFF
    200 Ω or more



OK
REPLACE YAW RATE SENSOR
NG


21.CHECK CAN BUS LINE FOR SHORT TO GND (YAW RATE SENSOR BRANCH WIRE)


    F100900E03
  1. Disconnect the J18 J/C2 connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Y1-3 (CANH) - Y1-1 (GND)
    Power switch OFF
    1 MΩ or more
    Y1-2 (CANL) - Y1-1 (GND)
    Power switch OFF
    1 MΩ or more

    HINT:
    Measure the resistance with the Y1 yaw rate sensor connector disconnected.



NG
REPLACE YAW RATE SENSOR BRANCH WIRE AND CONNECTOR (CANH, CANL)
OK


22.CONNECT CONNECTOR
  1. Reconnect the Y1 yaw rate sensor connector and J18 J/C2 connector.


NEXT


23.CHECK CAN BUS LINE FOR SHORT TO GND (HYBRID VEHICLE CONTROL ECU)


    H100769E15
  1. Disconnect the H14 hybrid vehicle control ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-4 (CG)
    Power switch OFF
    200 Ω or more
    D11-14 (CANL) - D1-4 (CG)
    Power switch OFF
    200 Ω or more



OK
REPLACE HYBRID VEHICLE CONTROL ECU
NG


24.CHECK CAN BUS LINE FOR SHORT TO GND (HYBRID VEHICLE CONTROL ECU BRANCH WIRE)


    C126168E03
  1. Disconnect the J18 J/C2 connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    H14-8 (CANH) - H14-1 (GND1)
    Power switch OFF
    1 MΩ or more
    H14-8 (CANH) - H14-4 (GND2)
    14-9 (CANL) - H14-1 (GND1)
    Power switch OFF
    1 MΩ or more
    14-9 (CANL) - H14-4 (GND2)

    HINT:
    Measure the resistance with the H14 hybrid vehicle control ECU connector disconnected.



NG
REPLACE HYBRID VEHICLE CONTROL ECU BRANCH WIRE AND CONNECTOR (CANH, CANL)
OK


25.CONNECT CONNECTOR
  1. Reconnect the H14 hybrid vehicle control ECU connector and J18 J/C2 connector.


NEXT


26.CHECK CAN BUS LINE FOR SHORT TO GND (GATEWAY ECU)


    H100769E15
  1. Disconnect the G1 gateway ECU connector.

  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-6 (CANH) - D1-4 (CG)
    Power switch OFF
    200 Ω or more
    D1-14 (CANL) - D1-4 (CG)
    Power switch OFF
    200 Ω or more



OK
REPLACE GATEWAY ECU
NG

REPLACE GATEWAY ECU BRANCH WIRE AND CONNECTOR (CA1H, CA1L)