Home › BRAKE › BRAKE › REAR DRUM BRAKE

REAR DRUM BRAKE > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. TEMPORARILY TIGHTEN REAR DRUM BRAKE BLEEDER PLUG
  1. Install the rear drum brake bleeder plug to the rear wheel brake cylinder.



2. INSTALL REAR WHEEL CYLINDER CUP KIT


    F101062E02
  1. Apply lithium soap base glycol grease to 2 new wheel cylinder cups and 2 pistons.

  1. Install the 2 wheel cylinder cups on each piston.

  1. Install the compression spring and the 2 pistons to the rear wheel brake cylinder.

  1. Install the 2 new cylinder dust boots to the rear wheel brake cylinder.



3. INSTALL FRONT OR UPPER REAR WHEEL BRAKE CYLINDER ASSEMBLY LH


    F101063
  1. Install the rear wheel brake cylinder with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Using SST, connect the brake line.

    SST
    09023-00101  

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }



4. APPLY HIGH TEMPERATURE GREASE


    F101065E02
  1. Apply high temperature grease to the shoe attached surface of the backing plate.



5. INSTALL REAR BRAKE PARKING BRAKE SHOE LEVER SUB-ASSEMBLY


    F101078
  1. Using needle-nose pliers, install the parking brake lever with a new C-washer.



6. INSTALL REAR BRAKE SHOE


    F045648E01
  1. Using needle-nose pliers, connect the No. 3 parking brake cable to the parking brake shoe lever.



    F045280E03
  1. Using SST, install the rear brake shoe, pin, shoe hold down spring and cup.

    SST
    09718-00010  



7. INSTALL REAR BRAKE SHOE RETURN SPRING
  1. Install the rear brake shoe return spring to the rear brake shoe.



8. INSTALL REAR BRAKE AUTOMATIC ADJUST LEVER LH


    F101060
  1. Install the rear brake automatic adjust lever and the rear brake automatic adjust lever tension spring to the front brake shoe.



9. INSTALL PARKING BRAKE SHOE STRUT SET LH


    F101064E02
  1. Apply high temperature grease to the adjusting bolt and assemble the strut set.

  1. Install the shoe return spring to the strut set.



    F101079E01
  1. Install the strut set as shown in the illustration.



10. INSTALL FRONT BRAKE SHOE


    F045279E03
  1. Connect the tension spring to the front brake shoe and rear brake shoe.

  1. Using SST, install the front brake shoe, pin, shoe hold down spring and cup.

    SST
    09718-00010  



11. CONNECT PARKING BRAKE SHOE STRUT SET LH


    F045278E03
  1. Using SST, connect the shoe return spring to the front brake shoe and rear brake shoe.

    SST
    09703-30011  

    NOTICE:
    Be careful not to damage the wheel cylinder boot.



12. CHECK REAR DRUM BRAKE INSTALLATION


  1. Check that each part is installed properly.

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining and drum.

    If they are not installed correctly as shown in the illustration, reinstall them.


    F040022E03



    F045281E01
  1. Measure the brake drum inside diameter and the diameter of the brake shoes. Check that the difference between the diameter is the correct shoe clearance.

    Standard shoe clearance:
    0.6 mm (0.024 in.)

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining and the drum.