Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Power Windows do not Operate at All

for Preparation Click here


DESCRIPTION

If all of the power windows do not operate, the power window regulator master switch may have no power or may be malfunctioning.

WIRING DIAGRAM


E124634E01


INSPECTION PROCEDURE

1.INSPECT FUSE (AM2, GAUGE, FR DOOR, ECU-IG)
  1. Remove the AM2 fuse from the engine room junction block.

  1. Remove the GAUGE, FR DOOR and ECU-IG fuses from the driver side junction block.

  1. Measure the resistance of the fuses.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2.INSPECT IG1 RELAY


    A092673E28
  1. Remove the IG1 relay from the driver side junction block.

  1. Measure the resistance of the relay.

Standard resistance:
Tester Connection
Specified Condition
3 - 5
10 kΩ or higher
3 - 5
Below 1 Ω (when battery voltage is applied to terminals 1 and 2)



NG
REPLACE IG1 RELAY
OK


3.CHECK WIRE HARNESS (MASTER SWITCH - BATTERY AND BODY GROUND)


    E124648E01
  1. Disconnect the P17 switch connector.

  1. Measure the voltage or resistance of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    P17-6 (B) - Body ground
    Power switch ON (IG)
    10 to 14 V
    P17-7 (BW) - Body ground
    Always
    10 to 14 V
    P17-11 (BDR) - Body ground
    Power switch ON (IG)
    10 to 14 V

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    P17-1 (E) - Body ground
    Always
    Below 1 Ω



OK
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
NG


4.CHECK WIRE HARNESS (MASTER SWITCH - JUNCTION BLOCK)


    E124639E01
  1. Disconnect the P17 switch connector.

  1. Disconnect the 1G and 1H junction block connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    P17-11 (BDR) - 1G-6
    Below 1 Ω
    P17-7 (BW) - 1H-10
    Below 1 Ω
    P17-6 (B) - 1H-11
    Below 1 Ω
    P17-11 (BDR) or 1G-6 - Body ground
    10 kΩ or higher
    P17-7 (BW) or 1H-10 - Body ground
    10 kΩ or higher
    P17-6 (B) or 1H-11 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.CHECK WIRE HARNESS (JUNCTION BLOCK - BODY GROUND)


    E124643E01
  1. Disconnect the 1B and 1E junction block connectors.

  1. Measure the voltage and resistance of the wire harness side connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    1B-1 - Body ground
    10 to 14 V

    Standard resistance:
    Tester Connection
    Specified Condition
    1E-17 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.CHECK BASIC FUNCTION OF PUSH BUTTON START SYSTEM
  1. Check that the push button start system operates normally.

    OK:
    Push button start system operates normally.



NG
GO TO PUSH BUTTON START SYSTEM
OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY