Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

DTC    74-40    Short in Speaker Circuit

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
74-40
Short is detected in speaker output circuit.
  1. Wire harness
  2. Speaker
  3. Stereo component amplifier
This circuit has a fail-safe function.
  1. When a short in the speaker circuit is detected, all sound outputs are stopped.

WIRING DIAGRAM


E107207E01


E107208E01


E107209E01


INSPECTION PROCEDURE

HINT:
After the inspection is completed, clear the DTCs.

1.CHECK VEHICLE EQUIPMENT

Vehicle equipment 
Vehicle equipment
Proceed to
6 speaker system
A
9 speaker system
B


B
Go to step 9
A


2.INSPECT RADIO RECEIVER
  1. Disconnect the R3 and R4 receiver connectors.

  1. Clear DTC and recheck.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



NG
REPLACE RADIO RECEIVER
OK


3.CHECK OPERATION
  1. Reconnect the R3 and R4 receiver connectors.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



OK
END
NG


4.CHECK WIRE HARNESS (RADIO RECEIVER - SPEAKER)


    E107212E03
  1. Disconnect the R3 and R4 receiver connectors.

  1. Disconnect the T6, T7, R11 and R12 speaker connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    R3-2 (FL+) - T6-4
    Below 1 Ω
    R3-6 (FL-) - T6-2
    Below 1 Ω
    R3-1 (FR+) - T7-4
    Below 1 Ω
    R3-5 (FR-) - T7-2
    Below 1 Ω
    R4-2 (RL+) - R11-1
    Below 1 Ω
    R4-6 (RL-) - R11-2
    Below 1 Ω
    R4-1 (RR+) - R12-1
    Below 1 Ω
    R4-3 (RR-) - R12-2
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.CHECK WIRE HARNESS (FRONT NO. 1 SPEAKER - FRONT NO. 2 SPEAKER)


    E107213E04
  1. Disconnect the F12, F13, T6 and T7 speaker connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    F12-1 - T6-3
    Below 1 Ω
    F12-2 - T6-1
    Below 1 Ω
    F13-1 - T7-3
    Below 1 Ω
    F13-2 - T7-1
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.INSPECT FRONT NO. 1 SPEAKER


    E107214
  1. Disconnect the F12 and F13 speaker connectors.

  1. Measure the resistance of the speaker.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    Approximately 4 Ω



NG
REPLACE FRONT NO. 1 SPEAKER
OK


7.INSPECT FRONT NO. 2 SPEAKER
  1. Check that the malfunction disappears when the speaker is replaced with a normal one.

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speakers.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the inspection above on both LH and RH sides.



NG
REPLACE FRONT NO. 2 SPEAKER
OK


8.INSPECT REAR NO. 1 SPEAKER


    E107214
  1. Disconnect the R11 and R12 speaker connectors.

  1. Measure the resistance of the speaker.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    Approximately 4 Ω



NG
REPLACE REAR NO. 1 SPEAKER
OK

REPLACE RADIO RECEIVER 

9.INSPECT STEREO COMPONENT AMPLIFIER
  1. Disconnect the S14 and S29 amplifier connectors.

  1. Clear DTC and recheck.

  1. Check if DTC 70-40 is output.

    OK:
    DTC 74-40 is not output.



NG
REPLACE STEREO COMPONENT AMPLIFIER
OK


10.CHECK OPERATION
  1. Reconnect the S14 and S29 amplifier connectors.

  1. Check that audio can be heard from the speaker.

    OK:
    Audio can be heard.



OK
END
NG


11.CHECK WIRE HARNESS (STEREO COMPONENT AMPLIFIER - SPEAKER)


    E107215E03
  1. Disconnect the S14 and S29 amplifier connectors.

  1. Disconnect the C8, F12, F13, T6, T7, T8 and T9 speaker connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    S29-2 (WFL+) - F12-1
    Below 1 Ω
    S29-1 (WFL-) - F12-2
    Below 1 Ω
    S29-9 (WFR+) - F13-1
    Below 1 Ω
    S29-3 (WFR-) - F13-2
    Below 1 Ω
    S14-8 (FL+) - T6-4
    Below 1 Ω
    S14-7 (FL-) - T6-2
    Below 1 Ω
    S14-2 (FR+) - T7-4
    Below 1 Ω
    S14-6 (FR-) - T7-2
    Below 1 Ω
    S14-3 (RL+) - T8-4
    Below 1 Ω
    S14-9 (RL-) - T8-2
    Below 1 Ω
    S14-10 (RR+) - T9-4
    Below 1 Ω
    S14-4 (RR-) - T9-2
    Below 1 Ω
    S29-4 (CTR+) - C8-2
    Below 1 Ω
    S29-10 (CTR-) - C8-1
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


12.CHECK WIRE HARNESS (REAR NO. 1 SPEAKER - REAR NO. 2 SPEAKER)


    E107213E05
  1. Disconnect the R11, R12, T8 and T9 speaker connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    R11-1 - T8-3
    Below 1 Ω
    R11-2 - T8-1
    Below 1 Ω
    R12-1 - T9-3
    Below 1 Ω
    R12-2 - T9-1
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


13.INSPECT FRONT NO. 1 SPEAKER


    E107214
  1. Disconnect the F12 and F13 speaker connectors.

  1. Measure the resistance of the speaker.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    Approximately 4 Ω



NG
REPLACE FRONT NO. 1 SPEAKER
OK


14.INSPECT FRONT NO. 2 SPEAKER
  1. Check that the malfunction disappears when the speaker is replaced with a normal one.

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speakers.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the inspection above on both LH and RH sides.



NG
REPLACE FRONT NO. 2 SPEAKER
OK


15.INSPECT REAR NO. 1 SPEAKER


    E107214
  1. Disconnect the R11 and R12 speaker connectors.

  1. Measure the resistance of the speaker.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    Approximately 4 Ω



NG
REPLACE REAR NO. 1 SPEAKER
OK


16.INSPECT REAR NO. 2 SPEAKER
  1. Check that the malfunction disappears when the speaker is replaced with a normal one.

    OK: :
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the rear No. 2 speakers.
    2. When there is a possibility that either the right or left rear speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the inspection above on both LH and RH sides.



NG
REPLACE REAR NO. 2 SPEAKER
OK


17.INSPECT FRONT STEREO COMPONENT SPEAKER


    E116557
  1. Disconnect the C8 speaker connector.

  1. Measure the resistance of the speaker.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    1.2 to 2.2 Ω



NG
REPLACE FRONT STEREO COMPONENT SPEAKER
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE