Home › SUSPENSION & AXLE › AXLE › FRONT AXLE HUB

FRONT AXLE HUB > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.



1. REMOVE FRONT WHEEL


2. REMOVE FRONT AXLE HUB NUT LH


    F047428E01
  1. Using SST and a hammer, unstake the axle hub nut.

    SST
    09930-00010  

    NOTICE:
    1. Place SST on the flat part of the nut's recess.
    2. Do not grind the SST tip with a grinder or equivalent.
    3. Unstake the front axle hub nut completely when removing it.
    4. Do not damage the front drive shaft LH threads.

  1. Using a 30 mm socket wrench, remove the axle hub nut.



3. DISCONNECT FRONT SPEED SENSOR LH


    F046175E01
  1. Disconnect the sensor connector.



    F046179E02
  1. Remove the 2 bolts (A and B) and 2 sensor clamps from the body and front shock absorber.

    HINT:
    The bolt B is tightened together with the brake flexible hose clamp.



    F047471E01
  1. Remove the clip from the front shock absorber.

  1. Remove the bolt and sensor.

    NOTICE:
    Do not allow foreign matter to attach to the tip or connecting portion of the speed sensor.



4. DISCONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH


    C067088E05
  1. Remove the 2 bolts and disconnect the disc brake caliper from the steering knuckle.

    NOTICE:
    Hang down the disc brake caliper with a wire or equivalent.



5. REMOVE FRONT DISC

NOTICE:
Ensure no oil attaches to the disc surface.



6. DISCONNECT TIE ROD END SUB-ASSEMBLY LH


    F047429E01
  1. Remove the clip and castle nut.

  1. Using SST, disconnect the tie rod end from the steering knuckle.

    SST
    09628-00011  

    NOTICE:
    1. Do not damage the front disc brake dust cover.
    2. Be sure to hang the tie rod end with a string to prevent SST from dropping.
    3. Do not damage the ball joint dust cover.
    4. Do not damage the steering knuckle.
    5. Securely hang SST to the spacer of the steering knuckle.
    6. Replace the steering knuckle with a new one if the spacer comes off the steering knuckle.



7. DISCONNECT NO. 1 FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER LH


    C080293E01
  1. Remove the bolt and 2 nuts.

  1. Push down the No. 1 front suspension lower arm and disconnect the front lower ball joint.



8. REMOVE FRONT AXLE ASSEMBLY LH
  1. Using a plastic-faced hammer, tap the end of the front drive shaft and disengage the fitting between the front drive shaft and front axle.

    HINT:
    If it is difficult to disengage, tap the end of the front drive shaft with a brass bar and hammer.

  1. Push the front axle outward from the vehicle to remove the front drive shaft from the front axle.

    NOTICE:
    1. Be careful not to push the front axle outward from the vehicle more than is necessary to remove it.
    2. Be careful not to damage the drive shaft outboard joint boot.
    3. Be careful not to damage the speed sensor rotor.
    4. Hang the front drive shaft down with a string or equivalent.



    C094903E01
  1. Remove the 2 bolts and 2 nuts, and remove the front axle from the front shock absorber.



9. REMOVE FRONT NO. 1 WHEEL BEARING DUST DEFLECTOR LH


    G028520E01
  1. Mount the steering knuckle in a soft vise.

  1. Using a screwdriver, remove the deflector from the steering knuckle.

    NOTICE:
    Be careful not to damage the steering knuckle.



10. REMOVE LOWER BALL JOINT ASSEMBLY


    F046084E03
  1. Remove the clip and castle nut.

  1. Using SST, remove the lower ball joint.

    SST
    09611-36020  

    NOTICE:
    1. Do not damage the steering knuckle.
    2. Securely hang SST to the spacer of the steering knuckle.
    3. Replace the steering knuckle with a new one if the spacer comes off the steering knuckle.



11. REMOVE FRONT AXLE HUB SUB-ASSEMBLY LH


    G028521E01
  1. Remove the 4 bolts, dust cover and front axle hub.