Home › BODY › INTERIOR › ROOF HEADLINING

ROOF HEADLINING > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



2. REMOVE FRONT DOOR SCUFF PLATE LH


    B073586E02
  1. Using a screwdriver, detach the 8 claws and 2 clips, and remove the scuff plate.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



4. REMOVE COWL SIDE TRIM BOARD LH


    B073588E02
  1. Using a screwdriver, detach the claw and 2 clips, and remove the trim board.

    HINT:
    Tape the screwdriver tip before use.



5. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



6. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


7. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH


8. REMOVE FRONT PILLAR GARNISH CORNER PIECE LH


    B132622E01
  1. Put protective tape as shown in the illustration.

    Standard measurement:
    Area
    Specified Condition
    A
    2.0 mm (0.079 in.)
    B
    10.0 mm (0.394 in.)
    C
    50.0 mm (1.969 in.)

  1. Using a screwdriver, detach the 5 claws and remove the corner piece.

    HINT:
    Tape the screwdriver tip before use.



9. REMOVE FRONT PILLAR GARNISH CORNER PIECE RH

HINT:
Use the same procedures described for the LH side.



10. REMOVE FRONT PILLAR GARNISH LH


    B073594E03
  1. w/o Curtain Shield Airbag:
    Using a screwdriver, detach the 2 clips and remove the pillar garnish.

    HINT:
    Tape the screwdriver tip before use.



  1. w/ Curtain Shield Airbag:
    Remove the pillar garnish.



      B079223E02
    1. Pull the pillar garnish so that clip B detaches, the base of clip A detaches, and the tip of clip A locks in the pillar garnish's hole.

    2. Using needle-nose pliers, rotate clip A 90°. Then pull the pillar garnish to release the tip of clip A from the pillar garnish.

    3. Pull the pillar garnish in the direction indicated by the arrow in the illustration to detach the claw.



    B076392E04
  1. w/ Curtain Shield Airbag:
    Protect the curtain shield airbag LH.

    1. Thoroughly cover the airbag with cloth or nylon that is approximately 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with double-sided tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with the protective cover as soon as the pillar garnish is removed.



11. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



12. REMOVE REAR SEAT CUSHION ASSEMBLY


    B132600E01
  1. Detach the seat cushion's 2 front hooks from the vehicle body.

    NOTICE:
    Follow the instructions below carefully as the cushion frame deforms easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat for the other hook.

  1. Detach the seat cushion's rear hook.

  1. Remove the seat cushion.



13. REMOVE REAR DOOR SCUFF PLATE LH


    B073587E02
  1. Using a screwdriver, detach the 6 claws and clip, and remove the scuff plate.

    HINT:
    Tape the screwdriver tip before use.



14. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



15. REMOVE REAR SIDE SEATBACK FRAME LH


    B076393E02
  1. Remove the bolt.

  1. Detach the claw and remove the frame.



16. REMOVE REAR SIDE SEATBACK FRAME RH

HINT:
Use the same procedures described for the LH side.



17. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


18. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH


19. REMOVE LAP BELT OUTER ANCHOR COVER


    B076394E03
  1. Using a screwdriver, detach the 3 claws and remove the anchor cover.

    HINT:
    Tape the screwdriver tip before use.



20. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
  1. Remove the bolt and disconnect the floor anchor.



21. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
  1. Remove the bolt and disconnect the floor anchor.



22. REMOVE CENTER PILLAR LOWER GARNISH LH


    B073589E03
  1. Using a screwdriver, detach the 2 claws and 2 clips, and remove the lower garnish.

    HINT:
    Tape the screwdriver tip before use.



23. REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:
Use the same procedures described for the LH side.



24. REMOVE CENTER PILLAR GARNISH LH


    B073590E02
  1. Remove the 2 screws.

  1. Using a screwdriver, detach the clip and remove the pillar garnish.

    HINT:
    Tape the screwdriver tip before use.



25. REMOVE CENTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



26. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH
  1. Remove the bolt and disconnect the floor anchor.



27. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
  1. Remove the bolt and disconnect the floor anchor.



28. REMOVE BACK DOOR WEATHERSTRIP


29. REMOVE TONNEAU COVER ASSEMBLY


30. REMOVE REAR NO. 2 FLOOR BOARD


31. REMOVE REAR NO. 3 FLOOR BOARD


32. REMOVE REAR NO. 4 FLOOR BOARD


33. REMOVE REAR DECK FLOOR BOX


34. REMOVE DECK FLOOR BOX LH


35. REMOVE REAR NO. 1 FLOOR BOARD


    B132619E01
  1. Remove the 2 bolts and the 2 rope hooks.

  1. Using a clip remover, remove the 2 clips.

  1. Using a screwdriver, detach the 5 clips and remove the floor board.

    HINT:
    Tape the screwdriver tip before use.



36. REMOVE REAR DECK TRIM COVER


    B076395E02
  1. Using a screwdriver, detach the 4 claws and remove the trim cover.

    HINT:
    Tape the screwdriver tip before use.



37. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    B073591E02
  1. Remove the screw and 2 bolts.

  1. Using a clip remover, remove the clip.

  1. Using a screwdriver, detach the 7 claws and 3 clips, and remove the side panel.

    HINT:
    Tape the screwdriver tip before use.



38. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    B079224E02
  1. Remove the screw and 2 bolts.

  1. Using a clip remover, remove the clip.

  1. Using a screwdriver, detach the 6 claws and 2 clips, and remove the side panel.

    HINT:
    Tape the screwdriver tip before use.



39. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH


    B073592E03
  1. Using a screwdriver, detach the 6 clips and claw, and remove the inner garnish.

    HINT:
    Tape the screwdriver tip before use.



40. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



41. REMOVE MAP LIGHT ASSEMBLY


    B076771E02
  1. Remove the 2 screws.

  1. Using a moulding remover, detach the 4 clips and remove the map light.

  1. Disconnect the map light connector.



42. REMOVE NO. 1 ROOM LIGHT ASSEMBLY


    B076772E03
  1. Using a screwdriver, detach the 4 claws and remove the room light lens.

    HINT:
    Tape the screwdriver tip before use.



    B073597E02
  1. Using a screwdriver, detach the 4 claws and remove the room light.

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the room light connector.



43. REMOVE ASSIST GRIP COVER


    B076398E04
  1. Using a screwdriver, detach the 4 claws and remove the 2 covers.

    HINT:
    Tape the screwdriver tip before use.



44. REMOVE ASSIST GRIP SUB-ASSEMBLY


    B076399E02
  1. Using a screwdriver, detach the 4 claws and remove the assist grip.

    HINT:
    Tape the screwdriver tip before use.



45. REMOVE VISOR ASSEMBLY LH


    B075287E01
  1. Remove the 2 screws.

  1. Disconnect the connector and remove the visor.



46. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



47. REMOVE VISOR HOLDER


    B050596E01
  1. Remove the visor holder by turning it counterclockwise.



48. REMOVE ROOF HEADLINING ASSEMBLY


    B073598E02
  1. Remove the 3 clips and headlining.

  1. Remove the silencer pads and headlining pad from the headlining.

  1. Remove the wire harness.