Home › BODY ELECTRICAL › WIPER AND WASHER › WIPER SWITCH

WIPER SWITCH > INSPECTION

for Preparation Click here



1. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY


    E137875E02
    I038011E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Front wiper switch:
    Tester Connection
    Switch Position
    Specified Condition
    C14-2 (+B) - C14-3 (+1)
    MIST
    Below 1 Ω
    C14-1 (+S) - C14-3 (+1)
    OFF
    Below 1 Ω
    C14-1 (+S) - C14-3 (+1)
    INT
    Below 1 Ω
    C14-2 (+B) - C14-3 (+1)
    LO
    Below 1 Ω
    C14-2 (+B) - C14-4 (+2)
    HI
    Below 1 Ω
    Rear wiper switch:
    Tester Connection
    Switch Position
    Specified Condition
    C13-2 (EW) - C13-6 (C1R),
    C13-2 (EW) - C13-7 (+1R)
    OFF
    10 kΩ or higher
    C13-2 (EW) - C13-6 (C1R)
    INT
    Below 1 Ω
    C13-2 (EW) - C13-7 (+1R)
    ON
    Below 1 Ω
    Front washer switch:
    Tester Connection
    Switch Position
    Specified Condition
    C13-2 (EW) - C13-3 (WF)
    OFF
    10 kΩ or higher
    C13-2 (EW) - C13-3 (WF)
    ON
    Below 1 Ω

    Standard resistance:
    Rear washer switch:
    Tester Connection
    Switch Position
    Specified Condition
    C14-5 (WR) - C13-2 (EW),
    C13-2 (EW) - C13-7 (+1R)
    OFF
    10 kΩ or higher
    C14-5 (WR) - C13-2 (EW)
    ON (WASH1)
    Below 1 Ω
    C14-5 (WR) - C13-2 (EW),
    C13-2 (EW) - C13-7 (+1R)
    ON (WASH2)
    Below 1 Ω



  1. Intermittent Operation Check

    1. Connect the voltmeter positive (+) lead to terminal C14-3 (+1) of the connector and the voltmeter negative (-) lead to terminal C13-2 (EW).

    2. Connect the positive battery (+) lead to terminal C14-2 (+B) of the connector and the negative battery (-) lead to terminals C13-2 (EW) and C14-1 (+S).

    3. Turn the wiper switch to the INT position.

    4. Connect the positive battery (+) lead to terminal C14-1 (+S) of the connector for 5 seconds.



    5. Connect the negative battery (-) lead to terminal C14-1 (+S) of the connector. Operate the intermittent wiper relay and measure the voltage between terminals C14-3 (+1) and C13-2 (EW)

      OK:
      Refer to the illustration below.



      E056399E36



    I032848E07
  1. Front Washer Operation Check

    1. Turn the wiper switch to the OFF position.

    2. Connect the positive battery (+) lead to terminal C14-2 (+B) of the connector, the negative battery (-) lead to terminals C14- 1 (+S) and the terminal C13-2 (EW).

    3. Connect the voltmeter positive (+) lead to terminal C14-3 (+1) of the connector and the voltmeter negative (-) lead to terminal C13-2 (EW).

    4. Turn the washer switch to the ON and OFF positions, and measure the voltage between terminals C14-3 (+1) and C13-2 (EW).

      OK:
      Refer to the illustration.