TRAP CANISTER > INSTALLATION |
| 1. INSTALL TRAP CANISTER WITH PUMP MODULE |
![]() |
Install the fuel tank vent hose.
Align the fuel tank vent hose connector with the pipe, then push in the fuel tank vent hose connector until the retainer makes a "click" sound to install the fuel tank vent hose to the trap canister with pump module.
![]() |
Install a new gasket to the fuel tank.
While being careful that the gasket does not drop in the fuel tank, insert the trap canister with pump module to the fuel tank.
Install the trap canister with pump module and ground terminal of the fuel tank wire with the 2 bolts.
Install the tube of the fuel tank vent hose to the 2 No. 1 fuel tube with grommet clamps.
Install the clamp to the fuel tank vent hose and canister hose.
Connect the canister pump module connector.
Install the fuel tank vent hose to the 2 No. 1 fuel tube with grommet clamps.
Install the tube of the fuel tank to canister tube to the clamp.
Install the tube of the fuel tank main tube to the clamp.
Install the clamp to the fuel tank vent hose and canister hose.
| 2. INSTALL FUEL TANK SUB-ASSEMBLY |
Set the fuel tank to a transmission jack.
Operate the transmission jack, and then install the fuel tank to the vehicle.
Operate the transmission jack, and then connect the fuel tank inlet pipe.
![]() |
Install the No. 1 fuel tank band RH and LH with the 4 bolts.
Install the fuel tube connector and fuel filler pipe clamp to the fuel tank inlet pipe.
![]() |
Connect the No. 1 canister tube.
Align the No. 1 canister tube connector with the pipe, and then push in the No. 1 canister tube connector until the retainer makes a "click" sound to connect the No. 1 canister tube to the fuel tank to filler pipe.
![]() |
Connect the fuel suction tube.
Align the suction tube connector with the pipe, and then push in the suction tube connector until the retainer makes a "click" sound to connect the fuel suction tube to the fuel tank to filler pipe.
![]() |
Connect the fuel tank vent hose.
Align the fuel tank vent hose connector with the pipe, and then push in the fuel tank vent hose connector until the retainer makes a "click" sound to connect the fuel tank vent hose to the canister filter.
![]() |
Connect the No. 2 fuel tank main tube.
Align the fuel tube connector with the pipe, and then push in the fuel tube connector until the retainer makes a "click" sound to connect the No. 2 fuel tank main tube to the pipe.
Install the checker to the pipe.
![]() |
Connect the fuel tank to canister tube.
Align the fuel tank to canister tube connector with the pipe, and then push in the fuel tank to canister tube connector until the retainer makes a "click" sound to connect the fuel tank to canister tube to the pipe.
| 3. INSTALL FRONT EXHAUST PIPE |
![]() |
Using a vernier caliper, measure the free length of the compression spring.
![]() |
Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the exhaust manifold.
Connect the 2 exhaust pipe supports, and install the exhaust pipe.
Install the 2 compression springs and 2 bolts.
![]() |
Install the grommet of the heated oxygen sensor to the vehicle.
Connect the heated oxygen sensor connector.
Install the front floor carpet with the clip.
| 4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
![]() |
Connect the battery negative cable, and then tighten the nut.
| 5. INSPECT FOR FUEL LEAK |
Check that there are no leaks in the fuel system while fuel pressure is applied.
| 6. INSPECT FOR EXHAUST GAS LEAK |
| 7. INSTALL FRONT FLOOR PANEL BRACE |
![]() |
Install the floor panel brace with the 2 bolts.
| 8. INSTALL REAR FLOOR SERVICE HOLE COVER |
![]() |
Attach new butyl tape to the rear floor service hole cover.
Connect the wire to wire connector.
Connect the fuel pump connector.
Install the rear floor service hole cover while adjusting it to the 3 convex parts of the floor panel.
| 9. INSTALL REAR SEAT CUSHION ASSEMBLY |
![]() |
Attach the seat cushion's rear hook to the center hinge.
Insert the inner belts through the slits on the seat cushion.
![]() |
Attach the seat cushion's 2 front hooks to the vehicle body.
Confirm that the seat cushion is firmly installed.
| 10. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL |
![]() |
Attach the 4 claws and 2 clips to install the instrument panel finish panel.
Install the clip.
| 11. INSTALL REAR NO. 3 FLOOR BOARD |
![]() |
Install the floor board, and then attach the 4 claws.
| 12. INSTALL REAR DECK FLOOR BOX |
![]() |
Install the rear deck floor box to the vehicle.
| 13. INSTALL REAR NO. 2 FLOOR BOARD |
![]() |
Install the floor board, and then lock the 2 cover knobs.
| 14. PERFORM INITIALIZATION |
Perform initialization (Click here).