Home › General › INTRODUCTION › WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS
BM2070E _V1 General _061965 INTRODUCTION _0301961 WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS F

INTRODUCTION  WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS  WHEEL ALIGNMENT STANDARD  


MEASURE VEHICLE HEIGHT


C236520E03
0.26,1.344 0.396,1.5 0.135,0.156 10 false A 1.406,1.302 1.542,1.458 0.135,0.156 10 false C 1.875,1.281 2.01,1.438 0.135,0.156 10 false B 3.073,1.302 3.208,1.458 0.135,0.156 10 false D

NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Measure the vehicle height.

Measurement points:

A: Ground clearance of front lower No. 1 suspension arm bushing set bolt center


B: Ground clearance of rear axle beam bushing set bolt center


C: Ground clearance of front wheel center


D: Ground clearance of rear wheel center


Vehicle Height (Unloaded Vehicle):
Front C - A Rear D - B
104 mm (4.09 in.)
95 mm (3.74 in.) *1
22 mm (0.866 in.)
8 mm (0.315 in.) *1


*1: ZVW40R-AWXEBQ



INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION


NOTICE:

Inspect while the vehicle is unloaded.


a.
C132440E41
2.406,1.104 2.51,0.823 2.51,0.823 2.74,0.823 false 0.604,0.698 1.031,0.698 1.031,0.698 1.031,1.469 false 2.771,0.729 2.958,0.896 0.188,0.167 10 false *2 0.417,0.625 0.604,0.781 0.188,0.156 10 false *1

Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.

Text in Illustration
*1 Turning Radius Gauge
*2 Camber-caster-kingpin Gauge


b.

Inspect the camber, caster and steering axis inclination.

Camber (Unloaded Vehicle):
Camber Inclination Right-left Difference
-0°13' +/- 0°45' (-0.22° +/- 0.75°)
-0°10' +/- 0°45' (-0.17° +/- 0.75°) *1
0°45' (0.75°) or less


*1: ZVW40R-AWXEBQ

Caster (Unloaded Vehicle):
Caster Inclination Right-left Difference
5°51' +/- 0°45' (5.85° +/- 0.75°)
5°37' +/- 0°45' (5.62° +/- 0.75°) *1
0°45' (0.75°) or less


*1: ZVW40R-AWXEBQ

Steering Axis Inclination (Unloaded Vehicle):
Steering Axis Inclination Reference
12°11' (12.18°)
11°58' (11.97°) *1


*1: ZVW40R-AWXEBQ



INSPECT TOE-IN (FRONT)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)


d.
C188968E31
0.823,0.604 0.823,1.135 false 1.365,0.604 1.365,1.01 1.365,1.01 0.833,1.01 false 2.521,1.333 2.521,1.667 false 0.74,1.135 0.917,1.302 0.177,0.167 10 false *a 2.427,1.698 2.604,1.854 0.177,0.156 10 false *b

Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).

Text in Illustration
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


e.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step C again.



f.
C188969E25
0.647,1.275 0.647,1.636 false 1.912,0.543 2.051,0.704 0.14,0.16 10 C 3.071,0.55 3.21,0.71 0.14,0.16 10 D 2.498,0.717 2.638,0.877 0.14,0.16 10 A 2.509,1.537 2.649,1.698 0.14,0.16 10 B 0.563,1.655 0.735,1.815 0.172,0.16 10 *a

Measure the distance between the tread center marks on the front of the wheels (dimension A).

Text in Illustration
*a Dimension A
V100135

Front of the Vehicle

Toe-in (Unloaded Vehicle)
Specified Condition
C + D: 0°10' +/- 0°12' (0.17° +/- 0.20°)
B - A: 2.0 +/- 2.0 mm (0.0787 +/- 0.0787 in.)

HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the rack ends.



INSPECT WHEEL ANGLE


C132439E11
0.863,0.204 1.036,0.380 0.173,0.176 10 *b 0.538,0.204 0.713,0.380 0.175,0.176 10 *a 2.397,0.204 2.570,0.380 0.173,0.176 10 *b 2.725,0.204 2.900,0.380 0.175,0.176 10 *a

a.

Put tread center marks on the rearmost points of a turning radius gauge.

Text in Illustration
*a Inside
*b Outside
V100135

Front of the Vehicle


b.

Turn the steering wheel fully to the left and right and measure the turning angle.

NOTICE:

Inspect while the vehicle is unloaded.


Wheel Turning Angle (Unloaded Vehicle):
Tire Size Inside Wheel Outside Wheel Reference
205/60R16 39°13' +/- 2°00' (39.22° +/- 2°)
39°26' +/- 2°00' (39.43° +/- 2°) *1
33°00' (33.00°)
33°13' (33.22°) *1
215/50R17 35°54' +/- 2°00' (35.90° +/- 2°) 30°59' (30.98°)


*1: ZVW40R-AWXEBQ

If the right and left inside wheel angles differ from the specified value, check and adjust the right and left rack end lengths.




INSPECT CAMBER (REAR)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Install a camber-caster-kingpin gauge.


b.

Inspect the camber.

Camber (Unloaded Vehicle):
Camber Inclination Right-left Difference
-1°26' +/- 0°30' (-1.43° +/- 0.50°)
-1°24' +/- 0°30' (-1.40° +/- 0.50°) *1
0°30' (0.50°) or less


*1: ZVW40R-AWXEBQ

HINT:

Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.




INSPECT TOE-IN (REAR)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


d.
C188968E31
0.823,0.604 0.823,1.135 false 1.365,0.604 1.365,1.01 1.365,1.01 0.833,1.01 false 2.521,1.333 2.521,1.667 false 0.74,1.135 0.917,1.302 0.177,0.167 10 false *a 2.427,1.698 2.604,1.854 0.177,0.156 10 false *b

Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).

Text in Illustration
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


e.

Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step A again.



f.
C188969E25
0.647,1.275 0.647,1.636 false 1.912,0.543 2.051,0.704 0.14,0.16 10 C 3.071,0.55 3.21,0.71 0.14,0.16 10 D 2.498,0.717 2.638,0.877 0.14,0.16 10 A 2.509,1.537 2.649,1.698 0.14,0.16 10 B 0.563,1.655 0.735,1.815 0.172,0.16 10 *a

Measure the distance between the tread center marks on the front of the wheels (dimension A).

Text in Illustration
*a Dimension A
V100135

Front of the Vehicle

Toe-in (Unloaded Vehicle):
Tire Size Specified Condition Right-left Difference
205/60R16 C + D: 0°13' +/- 0°17' ( 0.22° +/- 0.29°)
C + D: 0°08' +/- 0°17' ( 0.14° +/- 0.29°) *1
0°45' (0.75°) or less
B - A: 2.3 +/- 3.0 mm (0.0906 +/- 0.118 in.)
B - A: 1.4 +/- 3.0 mm (0.0551 +/- 0.118 in.) *1
-
215/50R17 C + D: 0°14' +/- 0°17' ( 0.23° +/- 0.29°) 0°45' (0.75°) or less
B - A: 2.4 +/- 3.0 mm (0.0945 +/- 0.118 in.) -


*1: ZVW40R-AWXEBQ

HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.