Home › Vehicle Exterior › BODY PANEL › FRONT FENDER FRONT APRON
BM2070E _01 Vehicle Exterior _061966 BODY WELD POINT _0301968 FRONT FENDER FRONT APRON F

BODY WELD POINT  FRONT FENDER FRONT APRON  ASSEMBLY REPLACEMENT  


K100937

With the radiator upper side support removed.


REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points


U155229E02
3.24,0.979 3.344,1.135 0.104,0.156 10 false 1 2.573,0.979 2.677,1.135 0.104,0.156 10 false 4 3.26,4.292 3.354,4.448 0.094,0.156 10 false 4 2.292,4.281 2.385,4.438 0.094,0.156 10 false 1 5.417,1.625 5.521,1.781 0.104,0.156 10 false 2 4.667,2.271 4.771,2.427 0.104,0.156 10 false 3 1.208,2.74 1.313,2.896 0.104,0.156 10 false 1 2.479,7.563 2.583,7.719 0.104,0.156 10 false 1 6.542,7.26 6.646,7.417 0.104,0.156 10 false 1 3.74,5.76 3.833,5.917 0.094,0.156 10 false 1 3.208,5.76 3.302,5.917 0.094,0.156 10 false 4 3.656,8.594 3.76,8.75 0.104,0.156 10 false 6 4.438,8.594 4.542,8.75 0.104,0.156 10 false 1 4.198,5.76 4.302,5.917 0.104,0.156 10 false 1 6.542,6.583 6.635,6.74 0.094,0.156 10 false 2 0.469,0.448 0.854,0.802 0.385,0.354 12 false LH:

U155331E02
0.469,0.448 0.854,0.802 0.385,0.354 12 false RH: 6.729,8.198 6.833,8.354 0.104,0.156 10 false 1 6.094,6.531 6.188,6.688 0.094,0.156 10 false 4 5.406,6.531 5.5,6.688 0.094,0.156 10 false 1 1.063,2.344 1.167,2.5 0.104,0.156 10 false 2 1.479,2.625 1.583,2.781 0.104,0.156 10 false 3 3.292,1.417 3.396,1.573 0.104,0.156 10 false 6 4.979,2.563 5.083,2.719 0.104,0.156 10 false 2 3.552,4.771 3.656,4.927 0.104,0.156 10 false 1 2.823,4.771 2.917,4.927 0.094,0.156 10 false 3 5.406,9.281 5.51,9.438 0.104,0.156 10 false 6

INSTALLATION


Symbol meaning
K108821

Spot Weld
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

When welding *1, make a hole on a new part for plug welding and weld the panel with the panel behind completely.

4.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)

5.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K140455E01
3.344,3.698 3.938,4.323 3.938,4.323 4.146,4.323 false 3.823,3.333 4.25,3.5 4.25,3.5 4.427,3.5 false 0.5,0.563 1.052,0.802 0.552,0.24 12 false LH: 0.729,2.875 1.042,3.073 0.313,0.198 10 false *1 4.479,3.396 6.385,3.635 1.906,0.24 10 false FRONT FENDER EXTENSION 4.229,4.219 5.875,4.438 1.646,0.219 10 false FRONT FENDER APRON

K140456E01
2.885,3.24 4.875,2.823 4.875,2.823 5.042,2.823 false 1.719,5.073 1.719,3.417 false 0.323,0.365 0.719,0.604 0.396,0.24 12 false RH: 5.115,2.729 6.76,2.958 1.646,0.229 10 false FRONT FENDER APRON 0.792,5.135 2.708,5.385 1.917,0.25 10 false FRONT FENDER EXTENSION 2.958,4.365 3.271,4.563 0.313,0.198 10 false *1