Home › Vehicle Exterior › BODY PANEL › CENTER BODY PILLAR › 2012.03–2019.03
BM2070E _01 Vehicle Exterior _061966 BODY WELD POINT _0301975 CENTER BODY PILLAR F

BODY WELD POINT  CENTER BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K100977

REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts


REMOVAL POINT
1.

*1 is reused.


U155256E02
2.51,4.615 2.271,3.865 2.271,3.865 2.094,3.865 false 6.229,1.125 6.823,1.302 0.594,0.177 10 false 20 (0.79) 0.438,2.75 1.104,2.927 0.667,0.177 10 false 150 (5.91) 3.563,3.792 4.146,3.969 0.583,0.177 10 false 20 (0.79) 3.271,5.188 3.865,5.365 0.594,0.177 10 false 50 (1.97) 1.229,5.479 1.979,5.656 0.75,0.177 10 false 420 (16.54) 3.833,6.458 4.417,6.635 0.583,0.177 10 false 20 (0.79) 3.833,8.833 4.417,9.01 0.583,0.177 10 false 40 (1.57) 1.927,3.76 2.083,3.906 0.156,0.146 10 false *1 0.219,9.323 0.75,9.594 0.531,0.271 10 false mm (in.) 2.25,5.781 2.354,5.938 0.104,0.156 10 false 3 3.396,5.771 3.5,5.927 0.104,0.156 10 false 3 1.656,7.135 1.76,7.292 0.104,0.156 10 false 4 1.271,9.052 1.375,9.208 0.104,0.156 10 false 2 2.958,9.052 3.063,9.208 0.104,0.156 10 false 2 5.24,8 5.344,8.156 0.104,0.156 10 false 1 6.531,8 6.635,8.156 0.104,0.156 10 false 1

INSTALLATION


Symbol meaning
K108823

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Before temporarily installing the new parts, weld the center body pillar reinforcement and center body pillar reinforce upper with the standard number of welding points.

5.

After welding the center body pillar reinforcement and center body pillar reinforce upper to the vehicle side, install the rear body front outside panel and *1.

6.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

7.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K140474E01
1.76,4.292 1.76,3.813 false 5.51,4.292 5.51,3.833 false 2.677,3.198 3.333,3.438 0.656,0.24 10 false 50 (1.97) 3.875,0.948 4.479,1.198 0.604,0.25 10 false 20 (0.79) 6.427,3.177 7.052,3.406 0.625,0.229 10 false 85 (3.35) 4.167,4.344 7.135,4.563 2.969,0.219 10 false CENTER BODY PILLAR REINFORCE UPPER 0.427,4.354 3.177,4.604 2.75,0.25 10 false CENTER BODY PILLAR REINFORCEMENT 0.208,9.521 0.802,9.76 0.594,0.24 10 false mm (in.)

K140475

K140476E01
3.073,6.073 3.219,6.073 3.219,6.073 3.521,6.906 false 3.927,1.76 3.385,0.875 3.385,0.875 3.24,0.875 false 0.771,0.781 3.323,1.042 2.552,0.26 10 false REAR BODY FRONT OUTSIDE PANEL 2.885,5.969 3.198,6.167 0.313,0.198 10 false *1