Home › Vehicle Exterior › BODY PANEL › REAR DOOR OUTER PANEL › 2012.03–2019.03
BM2070E _01 Vehicle Exterior _061966 BODY WELD POINT _0301992 REAR DOOR OUTER PANEL F

BODY WELD POINT  REAR DOOR OUTER PANEL  ASSEMBLY REPLACEMENT  


K101627

REMOVAL


Symbol meaning
K108818

Remove Weld Points


REMOVAL POINT
1.

Before removing the outer panel, mark the installation position with tape.

2.

Before removing the outer panel, establish its exact position in relation to the window frame using a reference marker, etc.

3.

After grinding off the hemming location, remove the outer panel.


U155329E01
2.004,2.295 2.107,2.446 0.104,0.152 10 1 1.076,1.802 2.127,2.146 1.052,0.343 10 Positioning Tape 3.029,2.099 4.222,2.412 1.193,0.313 10 Installation Postion 3.978,6.225 5.162,6.547 1.184,0.323 10 Hemming Location 3.704,8.421 4.502,8.577 0.798,0.156 10 Disc Sander

INSTALLATION


Symbol meaning
K108823

Plug Weld
K108833

Spot MIG Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Before temporarily installing the new parts, apply body sealer to the reinforcement, side impact protection beam and backside of the new parts.

NOTICE:

Do not close the drain hole.


HINT:

Apply sealer evenly about 10 mm (0.39 in.) from the flange and 3 mm (0.12 in.) in diameter on the outer panel and apply just enough sealer for the reinforcement and side impact protection beam to make contact.


2.

Bend the flange hem about 30° with a hammer and dolly. Then, fasten tightly with a hemming tool.

HINT:
·

Perform hemming in three steps, being careful not to warp the panel.

·

If a hemming tool cannot be used, hem with a hammer and dolly.



3.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K140478E01
5.375,5.875 5.375,5.417 5.375,5.417 5.51,5.417 false 6.313,7.031 6.188,7.031 6.188,7.031 6.021,6.615 false 5.906,6.021 6.01,5.854 6.01,5.854 6.115,5.854 false 5.833,8.875 5.708,8.875 5.708,8.875 5.656,8.604 false 2.323,4.115 2.323,3.76 false 0.281,1.24 1.042,1.479 0.76,0.24 10 false Positioning 0.281,1.385 0.667,1.583 0.385,0.198 10 false Tape 1.479,4.156 3.438,4.375 1.958,0.219 10 false REAR DOOR PANEL OUTER 4.698,1.896 5.313,2.115 0.615,0.219 10 false 10 (0.39) 6.156,3.5 6.875,3.719 0.719,0.219 10 false Drain hole. 4.938,6.417 5.24,6.635 0.302,0.219 10 false 30° 6.365,6.938 6.938,7.146 0.573,0.208 10 false Hammer 6.167,5.771 6.927,6 0.76,0.229 10 false Cloth Tape 5.563,5.333 5.979,5.563 0.417,0.229 10 false Dolly 5.885,8.781 6.865,9.031 0.979,0.25 10 false Hemming Tool 0.396,9.427 0.99,9.656 0.594,0.229 10 false mm (in.)