Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR › from 2019.03
BM2070E _01 Vehicle Exterior _061966 BODY PANEL _0301974 FRONT BODY PILLAR F

BODY PANEL  FRONT BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K100971

With the cowl top side panel removed.


Weld work for 980 MPa ultra high strength steel

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

*1: When welding 2 panels together including 980 MPa ultra high strength steel.

Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas


*2: When welding more than 3 panels together including 980 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas


NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.


REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts


REMOVAL POINT
1.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)

2.

*3 indicates welds to remove for easier removal.


K150767E01
3.229,2.917 3.385,3.063 0.156,0.146 10 false *3 4.875,1.198 5.5,1.385 0.625,0.188 10 false 75 (2.95) 0.406,9.25 0.938,9.521 0.531,0.271 10 false mm (in.) 2.469,7.833 2.625,7.979 0.156,0.146 10 false *3

K150769

INSTALLATION


Symbol meaning
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108830

Fillet Weld
K108831

Butt Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


4.

Follow the welding conditions when welding *1 and *2 to assure sufficient weld strength. (See the introduction)

5.

When welding *3, make a hole on a new part for plug welding and weld the panel with the panel behind completely.

6.

After welding the front body pillar inner to the vehicle side, install the front body pillar reinforce lower.

7.

After welding the front body pillar reinforce lower to the vehicle side, install the front body pillar upper outer.

8.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

9.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

10.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K150770E01
2.635,1.781 3.667,1.375 3.667,1.375 3.844,1.375 false 3.917,1.281 5.865,1.51 1.948,0.229 10 false FRONT BODY PILLAR INNER 3.344,2.698 3.656,2.896 0.313,0.198 10 false *1 2.917,2.698 3.229,2.896 0.313,0.198 10 false *1 2.5,2.698 2.813,2.896 0.313,0.198 10 false *1 2.771,4.375 3.083,4.573 0.313,0.198 10 false *1 2.198,4.385 2.51,4.583 0.313,0.198 10 false *1 1.615,4.25 1.927,4.448 0.313,0.198 10 false *3 4.781,7.823 5.385,8.083 0.604,0.26 10 false 10 (0.39) 0.135,9.51 0.719,9.75 0.583,0.24 10 false mm (in.) 0.594,7.625 0.906,7.823 0.313,0.198 10 false *1

K150771E01
5.396,5.281 4.875,4.552 4.875,4.552 4.74,4.552 false 1.875,4.438 4.729,4.708 2.854,0.271 10 false FRONT BODY PILLAR REINFORCE LOWER 5.552,7.063 5.865,7.26 0.313,0.198 10 false *1 4.927,8.51 5.24,8.708 0.313,0.198 10 false *1

K150772E01
5.292,5.583 4.76,4.646 4.76,4.646 4.615,4.646 false 1.177,3.792 1.49,3.99 0.313,0.198 10 false *3 2.104,4.542 4.563,4.792 2.458,0.25 10 false FRONT BODY PILLAR UPPER OUTER 5.302,7.292 5.615,7.49 0.313,0.198 10 false *2 5.115,8.698 5.427,8.896 0.313,0.198 10 false *2