Home › Vehicle Exterior › BODY PANEL › QUARTER PANEL › from 2019.03
BM2070E _01 Vehicle Exterior _061966 BODY PANEL _0301977 QUARTER PANEL F

BODY PANEL  QUARTER PANEL  ASSEMBLY REPLACEMENT  


K100993

Quarter Panel Replacement Using Adhesive


Work Procedure
1.

Cut the wheel arch portion.

2.

Heat the quarter panel adhesive area and remove the quarter panel.

HINT:

Using an industrial heater gun or gas burner, heat the quarter panel to 110 to 140°C. Make sure the quarter panel does not warp.


3.

Clean off any adhesive that remains on the vehicle.

HINT:
·

Using an industrial heater gun or gas burner, heat the adhesive to 110 to 140°C.

·

Using a scraper, scrape away the adhesive.

·

If adhesive remains, the strength of any subsequently applied adhesive will be weak.



4.

Using a disc grinder or belt sander, scuff and sand any adhesive that remains on the vehicle.

HINT:

Scuff at a width of approximately 10 mm (0.39 in.) over the previous adhesive coating.


5.

Apply adhesive to the exposed metal areas on the vehicle. Using a spatula, spread the adhesive evenly.

6.

Apply adhesive to the vehicle again.

7.

Using #60-120 grit sandpaper, scuff the adhesive application area on the new quarter panel.

8.

Apply adhesive to the new quarter panel. Using a spatula, spread the adhesive evenly.

9.

Using a vise grip or the palms of your hands, press the quarter panel so that the thickness of the adhesive is even.

10.

Complete installation the new quarter panel.

11.

Dry the adhesive areas of the new quarter panel.

HINT:
·

With dryer or equivalent (60°C): 60 minutes (complete hardening: 90 minutes)

·

Ambient temperature (25°C): 12 hours (complete hardening: 24 hours)




REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108828

Cut Location for Supply Parts


REMOVAL POINT
1.

*1 in illustration above indicates where the adhesive is located.

2.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.



K150784E01
3.865,5.063 5.24,4.354 5.24,4.354 5.292,4.354 false 6.438,5.677 6.146,5.677 false 5.323,4.26 5.479,4.406 0.156,0.146 10 false *1 5.979,5.594 6.135,5.74 0.156,0.146 10 false *1 0.292,0.135 0.677,0.49 0.385,0.354 12 false LH: 6.24,6.448 6.542,6.604 0.302,0.156 10 false a - a 3.26,4.792 3.354,4.938 0.094,0.146 10 true a 3.26,5.313 3.354,5.458 0.094,0.146 10 true a

K150785

K150786E01
3.344,4.771 2.031,4.198 2.031,4.198 1.917,4.198 false 1.031,5.76 1.344,5.76 false 1.75,4.135 1.906,4.281 0.156,0.146 10 false *1 1.354,5.698 1.51,5.844 0.156,0.146 10 false *1 0.927,6.615 1.229,6.771 0.302,0.156 10 false a - a 3.792,4.458 3.885,4.604 0.094,0.146 10 true a 3.792,4.979 3.885,5.125 0.094,0.146 10 true a 0.292,0.198 0.667,0.552 0.375,0.354 12 false RH:

K150787

INSTALLATION


Symbol meaning
K108821

Spot Weld
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108831

Butt Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

When welding *1, make a hole on a new part for plug welding and weld the panel with the panel behind completely.

4.

Before installing a new part, apply body sealer.

HINT:
·

Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.

·

Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.



5.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *2 in the illustration.

HINT:

Apply enough adhesive for the panels to stick to each other.


6.

Perform spot-welding on the flange indicated by *3 in the illustration. Modify/cut the spot tip as shown in the illustration*4 so that it can fit in to the narrow flange.

7.

After welding, apply foamed sealing material to the corresponding parts. (See the painting / coating)

8.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

9.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K150788E01
5.344,5.188 5.792,4.927 5.792,4.927 5.948,4.927 false 5.323,1.448 5.552,1.198 5.552,1.198 5.708,1.198 false 1.75,8.385 2.115,8.385 false 4.271,2.542 5.906,1.656 5.906,1.656 6.063,1.656 false 5.76,1.104 6.979,1.333 1.219,0.229 10 false QUARTER PANEL 6.115,1.563 6.427,1.76 0.313,0.198 10 false *2 3.729,3.469 4.042,3.667 0.313,0.198 10 false *3 0.198,0.115 0.552,0.365 0.354,0.25 12 false LH: 6,4.833 6.646,5.052 0.646,0.219 10 false Spot Tip 4.49,5.292 5.083,5.521 0.594,0.229 10 false 3 (0.12) 4.417,5.979 4.979,6.219 0.563,0.24 10 false 5 (0.20) 0.271,9.531 0.875,9.771 0.604,0.24 10 false mm (in.) 1.552,8.281 1.865,8.479 0.313,0.198 10 false *2 5.063,7.885 5.625,8.125 0.563,0.24 10 false 5 (0.20) 5.063,6.271 5.292,6.469 0.229,0.198 10 false *4

K150789E01
0.708,7.917 0.469,6.417 0.469,6.417 0.656,6.417 false 1.74,8.969 1.74,8.208 1.74,8.208 1.448,8.208 false 1.417,8.385 1.74,8.385 false 3.115,5.75 3.427,5.948 0.313,0.198 10 false *1 5.198,7.51 5.51,7.708 0.313,0.198 10 false *1 0.719,6.323 2.573,6.594 1.854,0.271 10 false FUEL FILLER OPENING LID 1.521,8.99 2.094,9.198 0.573,0.208 10 false RIVETS

K150790E01
5.219,5.479 5.604,5.156 5.604,5.156 5.781,5.156 false 1.521,8.156 1.948,8.156 false 1.344,1.698 1.521,1.698 1.521,1.698 3.281,2.677 false 1.781,1.208 1.927,1.208 1.927,1.208 2.281,1.573 false 0.198,0.146 0.563,0.396 0.365,0.25 12 false RH: 0.594,1.115 1.802,1.323 1.208,0.208 10 false QUARTER PANEL 3.344,3.792 3.656,3.99 0.313,0.198 10 false *3 1.167,1.604 1.365,1.802 0.198,0.198 10 false *2 5.844,5.063 6.469,5.292 0.625,0.229 10 false Spot Tip 4.406,5.563 4.948,5.792 0.542,0.229 10 false 3 (0.12) 4.302,6.229 4.865,6.49 0.563,0.26 10 false 5 (0.20) 4.927,6.542 5.24,6.74 0.313,0.198 10 false *4 0.146,9.563 0.719,9.781 0.573,0.219 10 false mm (in.) 5.135,7.708 5.698,7.969 0.563,0.26 10 false 5 (0.20) 1.979,8.052 2.177,8.25 0.198,0.198 10 false *2

K150791E01
3.156,8.667 3.469,8.865 0.313,0.198 10 false *1 5.792,7.656 6.104,7.854 0.313,0.198 10 false *1