Home › Vehicle Exterior › BODY PANEL › NAME PLATE › from 2019.03
BM2070E _01 Vehicle Exterior _061966 BODY PANEL _0301990 NAME PLATE F

BODY PANEL  NAME PLATE  ATTACHMENT POSITION  


1.

Heat the double-sided tape remaining on the body with an infrared lamp or equivalent.

HINT:

Heat the tape to 40 to 60°C for approximately 1 to 2 minutes.


2.

Wipe off the remaining double-sided tape using a clean cloth or equivalent.

NOTICE:

If a name plate is installed without thoroughly removing the remaining double-sided tape from the body, the name plate will not adhere properly. Make sure to thoroughly wipe off the double-sided tape.


3.

After cleaning the installation area of the body with degreasing agent, attach the name plate to the position shown in the illustration.

HINT:

The working environment should be 20°C when installing the name plate. If the working environment is below 20°C, heat the installation area of the body to 20 to 30°C and then install the name plate.



B501318C01
0.167,4.583 4,5.833 3.833,1.25 0.167,7.25 4,8.667 3.833,1.417 0.167,5.833 4,7.25 3.833,1.417 2.74,0.625 3.583,0.625 3.583,0.625 3.74,0.917 true 2.479,1.021 3.115,1.021 true 4.427,1.021 4.917,1.021 true 5.583,6.448 5.583,6.198 false 3.75,4.083 3.75,3.792 false 1.802,5.479 1.802,5.26 false 1.927,8.344 1.927,8.125 false 1.792,6.948 1.792,6.729 false 0.25,4.667 0.729,5 0.479,0.333 12 false *A 0.208,5.885 0.583,6.25 0.375,0.365 12 false *B 3.76,4.073 4.344,4.49 0.583,0.417 10 false *1 5.604,6.427 6.125,6.854 0.521,0.427 10 false ●*2 1.927,8.333 2.385,8.677 0.458,0.344 10 false ●*3 2.448,0.542 3.052,0.99 0.604,0.448 10 false <A> 2.177,0.938 2.781,1.385 0.604,0.448 10 false <B> 4.958,0.927 5.563,1.375 0.604,0.448 10 false <C> 3.479,4.063 4.083,4.51 0.604,0.448 10 false <A> 1.625,8.333 2.177,8.677 0.552,0.344 10 false <B> 5.313,6.438 5.917,6.885 0.604,0.448 10 false <C> 0.208,7.302 0.583,7.667 0.375,0.365 12 false *C 1.521,5.469 2.125,5.917 0.604,0.448 10 false <B> 1.802,5.469 2.26,5.813 0.458,0.344 10 false ●*3 1.802,6.917 2.26,7.26 0.458,0.344 10 false ●*3 1.51,6.917 2.115,7.365 0.604,0.448 10 false <B>
*A for Type A *B for Type B
*C for Type C - -
*1 NO. 1 BACK DOOR EMBLEM *2 NO. 1 BACK DOOR NAME PLATE
*3 NO. 2 BACK DOOR NAME PLATE - -
● Non-reusable part - -


B315267C01
1.865,1.115 1.865,1.906 false 5.219,1.104 5.219,1.906 false 5.375,3.906 5.375,3.271 false 1.688,3.917 1.688,3.281 false 5.104,1.917 5.479,2.104 0.375,0.188 10 false <B> 1.75,1.917 2.125,2.104 0.375,0.188 10 false <A> 5.063,3.896 5.563,4.313 0.5,0.417 10 false <B> 1.385,3.896 1.76,4.083 0.375,0.188 10 false <A> 0.5,0.167 0.917,0.5 0.417,0.333 12 false *A 3.938,0.177 4.333,0.583 0.396,0.406 12 false *B 1.667,3.896 2.167,4.219 0.5,0.323 10 false ●*1 5.365,3.885 5.865,4.208 0.5,0.323 10 false ●*1
*A for LH Side *B for RH Side
*1 SIDE PANEL EMBLEM - -
● Non-reusable part - -


INSTALL NO. 2 BACK DOOR NAME PLATE


a.

Install the No. 2 back door name plate as shown in the illustration.

Type A:

B283944C01
3.552,2.042 3.865,2.042 false 3.385,1.958 3.688,2.24 0.302,0.281 10 false *a 3.854,1.281 4.042,1.531 0.188,0.25 10 false A 3.969,2.573 4.156,2.74 0.188,0.167 10 false B 6.01,1.469 6.198,1.719 0.188,0.25 10 false C 6.229,1.781 6.417,2.031 0.188,0.25 10 false D
*a Profile of Back Door Panel - -


Standard Measurement:
Area Measurement Area Measurement
A 168.7 mm (6.64 in.) B 17.2 mm (0.677 in.)
C 95.1 mm (3.74 in.) D 23.0 mm (0.906 in.)


for Type B:

B501320C01
3.469,1.448 3.885,1.448 false 3.281,1.365 3.75,1.76 0.469,0.396 10 false *a 3.917,1.063 4.177,1.385 0.26,0.323 10 false A 4.031,2.542 4.24,2.781 0.208,0.24 10 false B 5.802,1.25 6.063,1.573 0.26,0.323 10 false C 6.198,1.552 6.458,1.875 0.26,0.323 10 false D
*a Profile of Back Door Panel - -


Standard Measurement:
Area Measurement Area Measurement
A 168.7 mm (6.64 in.) B 17.2 mm (0.677 in.)
C 90.2 mm (3.55 in.) D 18.3 mm (0.720 in.)


for Type C:

B501344C01
3.51,1.135 3.854,1.135 false 3.302,1.052 3.688,1.354 0.385,0.302 10 false *a 3.938,1.021 4.24,1.323 0.302,0.302 10 false A 4.031,2.51 4.292,2.719 0.26,0.208 10 false B 6.115,1.198 6.375,1.406 0.26,0.208 10 false C 6.281,1.625 6.542,1.833 0.26,0.208 10 false D
*a Profile of Back Door Panel - -


Standard Measurement:
Area Measurement Area Measurement
A 168.7 mm (6.64 in.) B 17.2 mm (0.677 in.)
C 97.7 mm (3.85 in.) D 15.0 mm (0.591 in.)




INSTALL NO. 1 BACK DOOR NAME PLATE


a.

Install the No. 1 back door name plate as shown in the illustration.

B500624C01
6.583,2.375 6.781,2.375 false 6.781,2.26 7.052,2.583 0.271,0.323 10 false *a 4.26,2.552 4.521,2.75 0.26,0.198 10 false A 4.479,1.5 4.74,1.698 0.26,0.198 10 false B 5.844,1.344 6.104,1.542 0.26,0.198 10 false C 6.271,2.01 6.531,2.208 0.26,0.198 10 false D
*a Profile of Back Door Panel - -


Standard Measurement:
Area Measurement Area Measurement
A 49.6 mm (1.95 in.) B 128.3 mm (5.05 in.)
C 137.7 mm (5.42 in.) D 54.1 mm (2.13 in.)




INSTALL SIDE PANEL EMBLEM


a.

Engage the 2 pins to install the side panel emblem as shown in the illustration.

B283943C01
4.979,1.771 5.281,2.208 5.281,2.208 5.542,1.76 true 5.198,2.229 5.469,2.51 0.271,0.281 10 false *a
*a Location Pin - -