Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2012.03–2016.05
NM2070E _51 Engine / Hybrid System _061858 2ZR-FXE ENGINE CONTROL _0301393 SFI SYSTEM UN GENERAL/CONTROL/DETAILS F

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

System Control Table

i.

The main components of the 2ZR-FXE engine control system are as follows.

Components Outline Quantity Function
ECM 32-bit CPU 1 The ECM optimally controls the SFI, ESA, EGR and ETCS-i to suit the operating conditions of the engine in accordance with the signals provided by the sensors.
Intake Mass Air Flow Meter Sub-assembly Hot-wire Type 1 This sensor has a built-in hot-wire to directly detect the intake air mass.
Intake Air Temperature Sensor Thermistor Type 1 This sensor detects the intake air temperature by means of an internal thermistor.
Crank Position Sensor
(Rotor Teeth)
Pick-up Coil Type
(36 - 2)
1 This sensor detects the engine speed and the crank angle.
Cam Position Sensor (No. 1 Crank Position Sensor)
(Rotor Teeth)
Magneto-Resistance Element (MRE) Type
(3)
1 This sensor performs cylinder identification and detects the VVT angle.
Throttle Body Assembly
- Throttle Position Sensor
Linear (Non-contact) Type 1 This sensor detects the throttle valve opening angle.
Knock Control Sensor Built-in Piezoelectric Element Type (Flat Type) 1 This sensor detects the occurrence of the engine knocking indirectly from the vibration of the cylinder block caused by the occurrence of engine knocking.
E. F. I. Engine Coolant Temperature Sensor Thermistor Type 1 This sensor detects the engine coolant temperature by means of an internal thermistor.
Air Fuel Ratio Sensor (Bank 1, Sensor 1) Planar Type with Heater 1 As with the oxygen sensor, this sensor detects the oxygen concentration in the exhaust emission. However, it detects the oxygen concentration in the exhaust emission linearly.
Oxygen Sensor (Bank 1, Sensor 2) Cup Type with Heater 1 This sensor detects the oxygen concentration in the exhaust emission by measuring the electromotive force which is generated in the sensor itself.
Fuel Injector Assembly 12-hole Type 4 The fuel injector assembly is an electromagnetically-operated solenoid with a nozzle which injects fuel in accordance with signals from the ECM.




SYSTEM CONTROL


a.

System Control Table

i.

The engine control system of the 2ZR-FXE engine has the following systems. The ECM that controls this system is made by DENSO.

Components Function
Sequential Multiport Fuel Injection (SFI)
·

An L-type SFI system is used and the intake air mass is detected with a hot-wire type air flow meter.


·

The fuel injection system is a sequential multiport fuel injection system.


·

Fuel injection takes 2 forms:

-

Synchronous injection, which always takes place with the same timing in accordance with the basic injection duration and an additional correction based on the signals provided by the sensors.

-

Non-synchronous injection, which takes place at the time an injection request based on the signals provided by the sensors is detected, regardless of the crankshaft position.



·

Synchronous injection is further divided into group injection during a cold start, and independent injection after the engine is started.


Electronic Spark Advance (ESA)
·

Ignition timing is determined by the ECM based on signals from various sensors. The ECM corrects ignition timing in response to engine knocking.


·

This system selects the optimal ignition timing in accordance with the signals received from the sensors and sends (IGT) ignition signals to the igniters.


Electronic Throttle Control System-intelligent (ETCS-i) Optimally controls the opening angle of the throttle valve in accordance with the accelerator pedal input and the engine and vehicle conditions.
Variable Valve Timing-intelligent (VVT-i) Controls the camshaft (intake) to an optimal valve timing in accordance with the engine operating conditions.
Cooling Fan Control Cooling fan operation is controlled by signals from the ECM based on the engine coolant temperature, air conditioning operation conditions, and hybrid system coolant temperature.
Water Pump Control Engine water pump assembly operation is controlled by signals from the ECM.
Fuel Pump Control
·

Fuel pump operation is controlled by signals from the ECM.


·

The fuel pump is stopped when any of the SRS airbags deploy.


Air Fuel Ratio Sensor and Oxygen Sensor Heater Control Maintains the temperature of the air fuel ratio sensor or oxygen sensor at an appropriate level to increase the ability of the sensors to accurately detect the oxygen concentration.
Exhaust Gas Recirculation (EGR) Control
(For details, see page (Click here))
Based on the signals received from the sensors, the ECM determines the EGR volume in accordance with the engine operating conditions.
Evaporative Emission Control
·

The ECM controls the purge flow of evaporative emissions (HC) from the canister in accordance with the engine operating conditions.

·

Approximately 5 hours after the power switch is turned off, the ECM operates the leak detection pump to detect any fuel vapor leaks between the fuel tank assembly and the canister through changes in the fuel tank pressure.


Fail-safe When the ECM detects a malfunction, the ECM stops or controls the engine according to the data already stored in memory.
Diagnosis When the ECM detects a malfunction, the ECM records the malfunction and information that relates to the fault.



b.

Variable Valve Timing-intelligent (VVT-i) System

i.

The VVT-i system is designed to control the intake camshaft within a range of 41° (of crankshaft angle) to provide valve timing that is optimally suited to the engine operating condition. This improves torque in all engine speed ranges as well as increasing fuel economy, and reducing exhaust emissions.

W105067E08
2.063,1.51 1.635,0.698 1.635,0.698 1.542,0.698 true 1.813,3.01 1.427,2.51 1.427,2.51 1.333,2.51 true 3.885,2.115 3.885,2.958 true 3.76,1.344 3.76,0.698 3.76,0.698 3.844,0.698 true 0.208,0.583 1.51,1.156 1.302,0.573 10 false Camshaft Timing Oil Control Valve Assembly 3.698,2.979 5.135,3.385 1.438,0.406 10 false E. F. I. Engine Coolant Temperature Sensor 0.354,2.406 1.292,2.781 0.938,0.375 10 false Crank Position Sensor 5.417,1.948 5.833,2.177 0.417,0.229 10 false ECM 5.573,3.354 6.917,3.781 1.344,0.427 10 false Intake Mass Air Flow Meter Sub-Assembly 5.292,4.031 6.323,4.396 1.031,0.365 10 false Throttle Position Sensor 3.896,0.583 6.063,0.927 2.167,0.344 10 false Cam Position Sensor (No. 1 Crank Position Sensor)

W103141E07
3.552,1.5 3.271,0.865 3.271,0.865 3.146,0.865 false 2.625,2.917 1.958,3.208 1.958,3.208 1.865,3.208 false 3.667,0.708 4,0.927 0.333,0.219 10 false TDC 3.677,4.469 4.063,4.708 0.385,0.24 10 false BDC 3,1.323 3.281,1.573 0.281,0.25 10 false 29° 3.865,1.115 4.104,1.323 0.24,0.208 10 false 3° 4.094,1.146 4.469,1.396 0.375,0.25 10 false 12° 2.198,2.26 2.646,2.51 0.448,0.25 10 false 102° 4.5,3.74 4.833,3.99 0.333,0.25 10 false 31° 2.354,3.313 2.729,3.563 0.375,0.25 10 false 61° 0.396,3.094 1.844,3.333 1.448,0.24 10 false VVT-i Operation Range 1.667,0.75 3.115,1 1.448,0.25 10 false VVT-i Operation Range 0.677,0.125 2.5,0.344 1.823,0.219 10 false Intake Valve Opening Angle 0.677,0.354 2.625,0.573 1.948,0.219 10 false Exhaust Valve Opening Angle



c.

Cooling Fan Control

i.

The cooling fan control system achieves an optimal fan speed in accordance with the engine coolant temperature, air conditioning operating conditions and hybrid system coolant temperature.



d.

Water Pump Control

i.

The ECM regulates the amount of engine coolant circulation to suit the engine operating conditions. The ECM bases this control on signals such as the engine coolant temperature, vehicle speed and engine speed. As a result, the engine will be warmed up more quickly, and cooling loss will be reduced as well.



e.

Fuel Pump Control

i.

A fuel cut function is used to stop the fuel pump when any of the SRS airbags have deployed. When the power management control ECU detects an airbag deployment signal from the airbag ECU assembly, it transmits an engine off signal to the ECM. Upon receiving this signal, the ECM turns off the circuit opening relay.




CONSTRUCTION


a.

ECM

i.

The ECM is installed in the engine compartment. As a result, the wiring harness has been shortened, thus realizing weight reduction.



b.

Intake Mass Air Flow Meter Sub-assembly

i.

This compact and lightweight plug-in type intake mass air flow meter sub-assembly allows a portion of the intake air to flow through the detection area. By directly measuring the mass and the flow rate of the intake air, the detection precision is improved and the intake air resistance has been reduced.


ii.

This intake mass air flow meter sub-assembly has a built-in intake air temperature sensor.

W100957E10
2.635,1.26 2.333,0.406 2.333,0.406 2.25,0.406 true 2.74,1.573 3.021,2.333 3.021,2.333 3.115,2.333 true 4.375,1.438 4.813,2.167 4.813,2.167 4.865,2.167 true 2.073,0.323 2.281,0.604 0.208,0.281 10 false *1 3.146,2.24 3.354,2.438 0.208,0.198 10 false *2 4.906,2.083 5.115,2.281 0.208,0.198 10 false *3

Text in Illustration
*1 Platinum Hot-wire Element *2 Temperature Sensing Element
*3 Intake Air Temperature Sensor - -
V100135

Air Flow - -



c.

Crank Position Sensor and Cam Position Sensor (No. 1 Crank Position Sensor)

i.

A pick-up coil type crank position sensor is used. The timing rotor of the crankshaft consists of 34 teeth with 2 teeth missing. The crank position sensor outputs the crankshaft rotation signals every 10°, and the missing teeth are used to determine the top-dead-center.


ii.

A Magneto-Resistance Element (MRE) type cam position sensor (No. 1 crank position sensor) is used. To detect the camshaft position, a timing rotor that is part of the camshaft is used to generate 3 (3 high output, 3 low output) pulses for every 2 revolutions of the crankshaft.

W101509E04
1.646,1.969 2.75,3.406 2.75,3.406 2.823,3.406 true 1.031,1.292 0.635,0.406 0.635,0.406 0.542,0.406 true 5.198,1.094 5.76,0.427 5.76,0.427 5.844,0.427 true 5.073,2.156 5.688,3.208 5.688,3.208 5.76,3.208 true 5.885,0.333 6.083,0.542 0.198,0.208 10 false *3 0.375,0.323 0.573,0.531 0.198,0.208 10 false *1 2.854,3.302 3.052,3.51 0.198,0.208 10 false *2 5.802,3.115 6.125,3.323 0.323,0.208 10 false *4

Text in Illustration
*1 Crank Position Sensor *2 Crankshaft Timing Sprocket
*3 Cam Position Sensor (No. 1 Crank Position Sensor) *4 Timing Rotor

U191456E02
4.24,3.625 4.354,4.438 4.354,4.438 4.531,4.438 true 0.063,0.094 2.135,0.333 2.073,0.24 12 false Sensor Output Waveforms: 0.938,2.354 1.167,2.594 0.229,0.24 10 false 0V 0.948,1.438 1.177,1.677 0.229,0.24 10 false 5V 0.031,0.938 0.917,2.104 0.885,1.167 10 false Cam Position Sensor Signal (No. 1 Crank Position Sensor Signal) 0.042,3.281 0.76,4.125 0.719,0.844 10 false Crankshaft Position Sensor Signal 0.948,3.542 1.177,3.781 0.229,0.24 10 false 0V 4.594,4.323 5.677,4.563 1.083,0.24 10 false 2 Teeth Missing


iii.

The MRE type sensor consists of a magnet and a sensor with a built-in MRE. The direction of the magnetic field changes due to the profile (protruding and non-protruding portions) of the timing rotor, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the ECM changes to either high or low. The ECM detects the cam position based on this output voltage.


iv.

The differences between an MRE type sensor and a conventional pick-up coil type sensor are as follows.

Sensor Type MRE Pick-up Coil
Signal Output Constant digital output starts from low engine speeds. Analog output changes with the engine speeds.
Crankshaft Position and Camshaft Position Detection
·

Detected by comparing the NE signals with the switching of the high/low output that results from the protruding and non-protruding portions of the timing rotor.

·

Can also be detected based on the number of NE signals input during high/low outputs.


Detected by comparing the NE signals with the change of waveform that is output when the protruding portion of the timing rotor passes.

W100950E23
4.313,2.719 4.583,3.344 4.583,3.344 4.729,3.344 true 4.833,1.885 5.24,1.031 5.24,1.031 5.385,1.031 true 1.76,0.365 2.552,0.604 0.792,0.24 10 false MRE Type 4.677,0.417 5.906,0.656 1.229,0.24 10 false Pick-up Coil Type 5.427,0.927 6.292,1.125 0.865,0.198 10 false No Detection 4.781,3.25 5.667,3.448 0.885,0.198 10 false No Detection 0.24,1.333 0.719,1.771 0.479,0.438 10 false Engine Speed 0.25,2.417 0.74,2.844 0.49,0.427 10 false Sensor Output 3.583,2.5 4.063,2.917 0.479,0.417 10 false Sensor Output 6.438,2.688 6.917,3.083 0.479,0.396 10 false Analog Output 2.875,2.604 3.333,3 0.458,0.396 10 false Digital Output 3.583,1.333 4.063,1.729 0.479,0.396 10 false Engine Speed



d.

Throttle Position Sensor

i.

This non-contact type throttle position sensor uses a Hall IC, which is mounted on the throttle body assembly.

·

The Hall IC is surrounded by a magnetic yoke (located on the same axis as the throttle shaft). The Hall IC converts the changes that occur in the magnetic flux into electrical signals, and outputs them in the form of throttle valve position signals to the ECM.


·

The Hall IC contains circuits for the main and sub signals. It converts the throttle valve opening angle into electric signals that have differing characteristics, and outputs them to the ECM.


W101512E10
3.542,0.938 2.927,0.344 2.927,0.344 2.802,0.344 true 4.646,1.896 5.292,1.063 5.292,1.063 5.396,1.063 true 4.104,2.313 4.542,3.333 4.542,3.333 4.667,3.333 true 2.385,2.823 2.01,3.448 2.01,3.448 1.906,3.448 true 2.615,0.25 2.813,0.448 0.198,0.198 10 false *1 1.719,3.354 1.917,3.552 0.198,0.198 10 false *2 5.438,0.969 5.635,1.167 0.198,0.198 10 false *3 4.708,3.229 4.906,3.448 0.198,0.219 10 false *4

Text in Illustration
*1 Throttle Control Motor *2 Throttle Position Sensor
*3 Throttle Valve *4 Return Spring

W101590E08
1.594,1.635 1.854,1.135 1.854,1.135 1.458,1.135 true 1.583,2.708 1.344,2.958 1.344,2.958 1.344,3.042 true 0.594,2.792 0.688,2.792 0.688,2.792 1.521,2.344 true 0.583,1.563 0.698,1.563 0.698,1.563 1.521,1.958 true 0.688,0.646 2.25,0.865 1.563,0.219 10 false Throttle Position Sensor 0.948,1.031 1.448,1.24 0.5,0.208 10 false Magnet 2.427,1.583 2.802,1.76 0.375,0.177 10 false VTA1 4.333,0.865 4.542,1.083 0.208,0.219 10 false V 4.563,1.198 4.948,1.406 0.385,0.208 10 false VTA2 4.51,3.177 6.375,3.406 1.865,0.229 10 false Throttle Valve Opening Angle 5.5,1.698 5.927,1.906 0.427,0.208 10 false VTA1 3.646,1.49 4.156,1.938 0.51,0.448 10 false Output Voltage 3.917,2.479 4.792,2.896 0.875,0.417 10 false Throttle Valve Fully Closed 6.042,2.479 6.906,2.865 0.865,0.385 10 false Throttle Valve Fully Open 4.188,1.042 4.385,1.24 0.198,0.198 10 false 5 4.188,1.26 4.385,1.458 0.198,0.198 10 false 4 4.188,1.479 4.385,1.677 0.198,0.198 10 false 3 4.188,1.688 4.385,1.885 0.198,0.198 10 false 2 4.188,1.906 4.385,2.104 0.198,0.198 10 false 1 4.188,2.125 4.385,2.323 0.198,0.198 10 false 0 4.563,2.24 4.76,2.438 0.198,0.198 10 false 10 4.802,2.24 5,2.438 0.198,0.198 10 false 20 5.052,2.24 5.25,2.438 0.198,0.198 10 false 30 5.292,2.24 5.49,2.438 0.198,0.198 10 false 40 5.531,2.24 5.729,2.438 0.198,0.198 10 false 50 5.781,2.24 5.979,2.438 0.198,0.198 10 false 60 6.021,2.24 6.219,2.438 0.198,0.198 10 false 70 6.271,2.24 6.469,2.438 0.198,0.198 10 false 80 6.521,2.229 6.719,2.427 0.198,0.198 10 false 90 2.406,2 2.813,2.198 0.406,0.198 10 false VCTA 2.5,2.354 2.802,2.573 0.302,0.219 10 false ETA 2.427,2.854 2.802,3.052 0.375,0.198 10 false VTA2 3.01,2.094 3.385,2.313 0.375,0.219 10 false ECM 0.146,1.469 0.625,1.688 0.479,0.219 10 false Hall IC 0.146,2.698 0.615,2.906 0.469,0.208 10 false Hall IC 0.948,3.063 1.448,3.281 0.5,0.219 10 false Magnet



e.

Knock Control Sensor (Flat Type)

i.

In a conventional knock control sensor (resonant type), a vibration plate is built into the sensor. This plate has the same resonance point as the knocking* frequency of the engine block. This sensor can only detect vibration in this frequency band.

A flat type knock control sensor (non-resonant type) has the ability to detect vibration in a wider frequency band (from about 6 kHz to 15 kHz). It has the following features:

·

A flat type knock control sensor is installed to an engine by placing it over the stud bolt installed on the cylinder block sub-assembly. For this reason, a hole for the stud bolt exists in the center of the sensor.


·

In the sensor, a steel weight is located in the upper portion. An insulator is located between the weight and a piezoelectric element.


·

An open/short circuit detection resistor is integrated in the sensor.


*: The term "Knock" or "Knocking" is used in this case to describe either preignition or detonation of the air fuel mixture in the combustion chamber. This preignition or detonation refers to the air fuel mixture being ignited earlier than is advantageous. This use of "Knock" or "Knocking" is not primarily used to refer to a loud mechanical noise that may be produced by an engine.


ii.

The engine knocking frequency will vary slightly depending on the engine speed. A flat type knock control sensor can detect vibration even when the engine knocking frequency changes. Due to the use of a flat type knock control sensor, the vibration detection ability is increased compared to a conventional type knock control sensor, and more precise ignition timing control is possible.

W100530E40
3.417,2.938 3.927,2.5 3.927,2.5 4.052,2.5 true 3.417,1.833 3.927,1.406 3.927,1.406 4.063,1.406 true 0.146,0.115 3.26,0.49 3.115,0.375 12 false Characteristics of Knock Control Sensor : 0.906,0.656 4.698,0.948 3.792,0.292 10 false : Resonance Characteristic of Conventional Type (Resonant) 0.906,0.979 4.49,1.271 3.583,0.292 10 false : Resonance Characteristic of Flat Type (Non-resonant) 1.563,1.354 1.781,1.604 0.219,0.25 10 false (V) 1.135,2.24 1.667,2.469 0.531,0.229 10 false Voltage 3.083,3.354 3.781,3.563 0.698,0.208 10 false Frequency 5.26,3.167 5.573,3.417 0.313,0.25 10 false (Hz) 4.094,2.396 5.948,2.604 1.854,0.208 10 false Detection Band of Flat Type 4.104,1.313 6.271,1.531 2.167,0.219 10 false Detection Band of Resonant Type


iii.

Vibrations caused by knocking are transmitted to the steel weight. The inertia of this weight applies pressure to the piezoelectric element. This action generates electromotive force.


iv.

An open/short circuit detection resistor is integrated in the sensor. When the power switch is on, the open/short circuit detection resistor in the knock control sensor and the resistor in the ECM keep the voltage at terminal KNK1 constant. An Integrated Circuit (IC) in the ECM constantly monitors the voltage of terminal KNK1. If the open/short circuit occurs between the knock control sensor and the ECM, the voltage of terminal KNK1 will change and the ECM will detect the open/short circuit and store a Diagnostic Trouble Code (DTC).

W105068E09
1.073,1.427 0.729,1.031 0.729,1.031 0.51,1.031 true 1.021,1.573 0.708,1.271 0.708,1.271 0.51,1.271 true 1.031,1.688 0.5,1.688 true 2.583,1.677 2.583,2.219 true 5.583,1.198 6.031,0.583 6.031,0.583 6.302,0.583 true 5.74,1.219 6.094,0.906 6.094,0.906 6.313,0.906 true 1.5,2.417 1.729,2.677 0.229,0.26 10 false *a 5.333,2.417 5.563,2.677 0.229,0.26 10 false *b 0.333,0.948 0.563,1.208 0.229,0.26 10 false *1 0.333,1.177 0.563,1.438 0.229,0.26 10 false *2 0.333,1.594 0.563,1.854 0.229,0.26 10 false *3 2.5,2.24 2.729,2.5 0.229,0.26 10 false *4 6.344,0.49 6.573,0.75 0.229,0.26 10 false *3 6.344,0.813 6.573,1.073 0.229,0.26 10 false *5

Text in Illustration
*1 Steel Weight *2 Insulator
*3 Piezoelectric Element *4 Open Circuit Detection Resistor
*5 Vibration Plate - -
*a Flat Type Knock Control Sensor
(Non-Resonant Type)
*b Conventional Type Knock Control Sensor
(Resonant Type)

W101046E27
0.885,0.469 2.927,0.677 2.042,0.208 10 false Flat Type Knock Control Sensor 3.979,1.094 4.385,1.313 0.406,0.219 10 false KNK1 3.958,1.74 4.375,1.969 0.417,0.229 10 false EKNK 5.094,1.292 5.49,1.5 0.396,0.208 10 false ECM 2.177,1.292 2.656,1.573 0.479,0.281 10 false 200kΩ 1.719,2.021 4.094,2.229 2.375,0.208 10 false Open/Short Circuit Detection Resistor 0.771,2.313 2.188,2.531 1.417,0.219 10 false Piezoelectric Element



f.

Air Fuel Ratio Sensor and Oxygen Sensor

i.

A planar type air fuel ratio sensor and a cup type oxygen sensor are used. The basic construction of the air fuel ratio sensor and oxygen sensor is the same. However, they are divided into the planar type and the cup type, according to the different types of heater construction that are used.


ii.

The planar type air fuel ratio sensor uses alumina, which excels in heat conductivity and electrical insulation, to integrate a sensor element with a heater, thus improving the warm up performance of the sensor.


iii.

The cup type oxygen sensor contains a sensor element that surrounds a heater.

W104094E05
0.615,0.104 3.354,3.615 2.74,3.51 3.563,0.104 6.302,3.615 2.74,3.51 2.417,2.333 2.115,2.729 2.115,2.729 1.938,2.729 true 5.49,2.406 5.49,2.875 5.49,2.875 5.573,2.875 true 5.49,1.5 5.49,0.729 5.49,0.729 5.635,0.729 false 5.635,1.5 5.635,1.104 5.635,1.104 5.844,1.104 true 2.458,1.833 2.167,1.427 2.167,1.427 1.979,1.427 true 2.708,1.677 2.875,1.271 2.875,1.271 2.979,1.271 true 5.26,2.323 4.969,2.719 4.969,2.719 4.792,2.719 true 2.5,2.177 2.844,2.573 2.844,2.573 3.073,2.573 true 5.417,2.438 4.927,3.208 4.927,3.208 4.615,3.208 true 2.604,2.167 2.854,2.042 2.854,2.042 3.01,2.042 true 1.813,1.333 2.01,1.583 0.198,0.25 10 false *1 3.01,1.177 3.208,1.427 0.198,0.25 10 false *3 1.74,2.646 1.938,2.896 0.198,0.25 10 false *4 0.677,0.156 0.948,0.406 0.271,0.25 10 false *A 3.625,0.156 3.896,0.406 0.271,0.25 10 false *B 4.417,3.115 4.615,3.365 0.198,0.25 10 false *5 4.604,2.635 4.802,2.885 0.198,0.25 10 false *4 5.677,0.625 5.875,0.875 0.198,0.25 10 false *3 5.875,1.021 6.073,1.271 0.198,0.25 10 false *2 5.604,2.781 5.802,3.031 0.198,0.25 10 false *4 3.104,2.479 3.302,2.729 0.198,0.25 10 false *4 3.042,1.948 3.24,2.198 0.198,0.25 10 false *2

Text in Illustration
*A Air Fuel Ratio Sensor (Planar Type) *B Oxygen Sensor (Cup Type)
*1 Solid Electrolyte (Zirconia Element) *2 Atmosphere
*3 Heater *4 Platinum Electrode
*5 Sensor Element (Zirconia) - -


iv.

The air fuel ratio sensor and oxygen sensor differ in output characteristics.


v.

As illustrated below, the oxygen sensor is characterized by a sudden change in its output voltage at the threshold of the stoichiometric air-fuel ratio (14.7:1). In contrast, the air fuel ratio sensor data is approximately proportionate to the existing air-fuel ratio. The air fuel ratio sensor converts the oxygen density to current and sends it to the ECM. As a result, the detection precision of the air-fuel ratio has been improved. The air fuel ratio sensor data can be viewed using the Global TechStream (GTS).

W101588E12
1,2.406 2.854,2.635 1.854,0.229 10 false Air Fuel Ratio Sensor Circuit 2.302,1.281 2.656,1.469 0.354,0.188 10 false ECM 1.615,0.604 2.01,0.792 0.396,0.188 10 false A1A+ 1.635,1.823 2.021,1.99 0.385,0.167 10 false A1A- 1.594,0.813 2.031,1.01 0.438,0.198 10 false (3.3V) 1.594,2.021 2.031,2.219 0.438,0.198 10 false (2.9V) 4.604,0.802 5.448,1.01 0.844,0.208 10 false (0.1 to 1.0V) 5,0.615 5.448,0.792 0.448,0.177 10 false OX1B 5.052,1.844 5.438,2.01 0.385,0.167 10 false O1B- 5.74,1.26 6.156,1.479 0.417,0.219 10 false ECM 4.708,2.385 6.25,2.604 1.542,0.219 10 false Oxygen Sensor Circuit 4.771,3.031 6.24,3.24 1.469,0.208 10 false : Air Fuel Ratio Sensor 4.771,3.313 5.917,3.51 1.146,0.198 10 false : Oxygen Sensor 4.896,3.594 5.417,3.813 0.521,0.219 10 false 1.0 (V) 4.844,4.354 5.844,4.74 1,0.385 10 false Oxygen Sensor Output 4.896,5.365 5.146,5.542 0.25,0.177 10 false 0.1 4.375,5.667 5.063,5.885 0.688,0.219 10 false 19 (Lean) 3.354,5.667 3.688,5.875 0.333,0.208 10 false 14.7 2.292,5.667 2.875,5.854 0.583,0.188 10 false 11 (Rich) 1.896,3.604 2.344,3.844 0.448,0.24 10 false (V) 4.2 2.094,5.385 2.344,5.552 0.25,0.167 10 false 2.2 0.927,4.083 2.281,4.479 1.354,0.396 10 false Air Fuel Ratio Sensor Output* 0.99,4.604 2.198,5.177 1.208,0.573 10 false Data Displayed on Global TechStream (GTS) 3.125,5.938 4.021,6.219 0.896,0.281 10 false Air-Fuel Ratio 0.771,6.365 6.458,6.708 5.688,0.344 10 false *: This is a calculated value used internally in the ECM, and is not an ECM terminal voltage. 3.729,1.219 4.25,1.615 0.521,0.396 10 false Oxygen Sensor 0.271,1.208 0.823,1.771 0.552,0.563 10 false Air Fuel Ratio Sensor



g.

Camshaft Timing Oil Control Valve Assembly

i.

This camshaft timing oil control valve assembly controls the spool valve using duty-cycle control from the ECM. This allows hydraulic pressure to be applied to the VVT-i controller (camshaft timing gear assembly) advance or retard side. When the engine is stopped, the camshaft timing oil control valve assembly will move to the retard position.

W101511E05
2.906,1.813 3.396,2.188 3.396,2.188 3.479,2.188 true 2.49,1.813 1.99,2.188 1.99,2.188 1.917,2.188 true 2,1.333 1.427,1.01 1.427,1.01 1.375,1.01 true 1.927,1.49 1.406,1.313 1.406,1.313 1.365,1.313 true 3.24,1.229 3.385,0.583 3.385,0.583 3.438,0.583 true 1.75,2.094 1.927,2.302 0.177,0.208 10 false *a 3.521,2.104 3.698,2.313 0.177,0.208 10 false *b 1.188,0.906 1.365,1.115 0.177,0.208 10 false *1 1.188,1.208 1.365,1.417 0.177,0.208 10 false *2 2.198,0.573 2.375,0.781 0.177,0.208 10 false *c 2.615,0.417 2.792,0.625 0.177,0.208 10 false *d 3.469,0.479 3.667,0.688 0.198,0.208 10 false *3 3.021,0.573 3.198,0.781 0.177,0.208 10 false *c

Text in Illustration
*1 Spring *2 Sleeve
*3 Spool Valve - -
*a To Camshaft Timing Gear Assembly
(Advance Side)
*b To Camshaft Timing Gear Assembly
(Retard Side)
*c Drain *d Oil Pressure



h.

Ignition Coil Assembly

i.

An igniter is integrated with the ignition coils, which are provided independently in each cylinder. This improves ignition timing accuracy, reduces high-voltage loss and enhances the overall reliability of the ignition system by eliminating the distributor.


ii.

The spark plug caps, which provide contact to spark plugs, are integrated with an ignition coil assembly. Also, an igniter is enclosed to simplify the system.

W101587E05
3.75,0.625 4.552,0.292 4.552,0.292 4.625,0.292 true 3.667,1.781 4.521,1.458 4.521,1.458 4.615,1.458 true 3.729,2.156 4.542,1.875 4.542,1.875 4.615,1.875 true 3.542,1.51 2.656,1.104 2.656,1.104 2.573,1.104 true 3.479,3.302 2.688,3.031 2.688,3.031 2.615,3.031 true 4.677,0.208 4.875,0.458 0.198,0.25 10 false *1 4.677,1.365 4.875,1.615 0.198,0.25 10 false *4 4.677,1.792 4.875,2.042 0.198,0.25 10 false *5 2.406,1.021 2.604,1.271 0.198,0.25 10 false *2 2.417,2.917 2.615,3.167 0.198,0.25 10 false *3

Text in Illustration
*1 Igniter *2 Iron Core
*3 Spark Plug Cap *4 Secondary Coil
*5 Primary Coil - -



i.

Spark Plug

i.

Long-reach, thin-electrode type iridium tipped spark plugs are used. This type of spark plug allows the area of the cylinder head which receives the spark plugs to be made thick. Thus, the water jacket can be extended near the combustion chamber, which contributes to cooling performance.


ii.

Iridium-tipped spark plugs improve ignition performance while maintaining the same durability as platinum-tipped spark plugs.

W101515E07
4.49,1.865 5.833,2.188 5.833,2.188 5.896,2.188 true 4.5,1.75 5.771,1.177 5.771,1.177 5.875,1.177 true 4.021,5 4.458,3.302 4.458,3.302 4.677,3.302 true 3.677,4.563 4.115,2.865 4.115,2.865 4.344,2.865 true 2.906,4.552 2.635,3.344 2.635,3.344 2.354,3.344 true 5.938,1.083 6.156,1.26 0.219,0.177 10 false *1 5.948,2.083 6.167,2.26 0.219,0.177 10 false *2 4.74,3.198 4.958,3.375 0.219,0.177 10 false *3 3.302,5.427 3.521,5.635 0.219,0.208 10 false *a 4.385,2.76 4.604,2.938 0.219,0.177 10 false *3 2.177,3.25 2.396,3.427 0.219,0.177 10 false *3

Text in Illustration
*1 Iridium Tip *2 Platinum Tip
*3 Water Jacket - -
*a Cylinder Head Cross Section - -




OPERATION


a.

Variable Valve Timing-intelligent (VVT-i) System

i.

Based on engine speed, intake air volume, throttle position and engine coolant temperature, the ECM calculates optimal valve timing for all driving conditions. The ECM also controls the camshaft timing oil control valve assembly. In addition, the ECM uses signals from the cam position sensor (No. 1 crank position sensor) and the crank position sensor to detect the actual valve timing, thus providing feedback control to achieve the target valve timing.

W104556E08
0.385,0.594 1.854,0.802 1.469,0.208 10 false Crank Position Sensor 0.438,1.021 1.771,1.427 1.333,0.406 10 false Intake Mass Air Flow Meter Sub-assembly 0.344,1.781 1.854,2 1.51,0.219 10 false Throttle Body Assembly 0.375,2.552 1.813,2.958 1.438,0.406 10 false E. F. I. Engine Coolant Temperature Sensor 0.271,3.385 2.031,3.76 1.76,0.375 10 false Cam Position Sensor (No. 1 Crank Position Sensor) 0.448,4.292 1.875,4.5 1.427,0.208 10 false Vehicle Speed Signal 3.448,0.792 4.75,0.99 1.302,0.198 10 false Target Valve Timing 3.76,2.792 4.479,3.01 0.719,0.219 10 false Correction 3.479,3.344 4.781,3.531 1.302,0.188 10 false Actual Valve Timing 4.344,1.646 5.01,1.844 0.667,0.198 10 false Feedback 5.125,1.188 5.833,1.542 0.708,0.354 10 false Duty-cycle Control 5.875,0.802 6.958,1.365 1.083,0.563 10 false Camshaft Timing Oil Control Valve Assembly 3.865,3.99 4.25,4.188 0.385,0.198 10 false ECM 0.427,2.104 2.031,2.313 1.604,0.208 10 false -Throttle Position Sensor


ii.

When the camshaft timing oil control valve assembly is operated as illustrated below by the advance signal from the ECM, the resultant oil pressure is applied to the timing advance side vane chamber to rotate the camshaft in the timing advance direction.

W101517E17
0.5,1.563 0.385,0.969 0.385,0.969 0.49,0.969 true 0.604,2.313 0.729,3.042 0.729,3.042 0.865,3.042 true 6.615,1.25 6.99,1.438 0.375,0.188 10 false ECM 5.469,3.063 5.823,3.313 0.354,0.25 10 false Drain 4.208,2.708 5.042,2.958 0.833,0.25 10 false Oil Pressure 0.542,0.875 0.969,1.125 0.427,0.25 10 false Vane 0.917,2.938 2.115,3.188 1.198,0.25 10 false Rotation Direction 5.26,3.063 5.448,3.313 0.188,0.25 10 false In


iii.

When the camshaft timing oil control valve is operated as illustrated below by the retard signal from the ECM, the resultant oil pressure is applied to the timing retard side vane chamber to rotate the camshaft in the timing retard direction.

W101518E14
0.458,1.49 0.344,0.896 0.344,0.896 0.448,0.896 true 0.625,2.281 0.75,3.021 0.75,3.021 0.885,3.021 true 6.573,1.188 6.99,1.375 0.417,0.188 10 false ECM 4.823,2.969 5.177,3.219 0.354,0.25 10 false Drain 3.906,2.677 4.74,2.927 0.833,0.25 10 false Oil Pressure 0.5,0.802 0.927,1.052 0.427,0.25 10 false Vane 0.938,2.917 2.135,3.167 1.198,0.25 10 false Rotation Direction 5.25,2.969 5.438,3.219 0.188,0.25 10 false In


iv.

After reaching the target timing, the valve timing is held by keeping the camshaft timing oil control valve assembly in the neutral position unless the driving conditions change. This maintains the valve timing at the desired target position and prevents the engine oil from running out when it is unnecessary.



b.

Cooling Fan Control

i.

A cooling fan control system in which the ECM controls the cooling fan speed is used. Cooling fan speed is controlled in accordance with the engine coolant temperature, hybrid system coolant temperature and the air conditioning operating conditions.


ii.

This control is accomplished by operating the 2 fan motors in 2 stages. The fan motors operate in series to achieve low speed, and in parallel to achieve high speed.

W107894E02
1.979,1.042 1.917,1.042 1.917,1.042 1.917,1.635 false 0.208,1.396 1.771,1.792 1.563,0.396 10 false Air Conditioning Amplifier Assembly 0.271,0.375 1.708,0.76 1.438,0.385 10 false E. F. I. Engine Coolant Temperature Sensor 2.021,0.938 2.719,1.292 0.698,0.354 10 false CAN (Sub Bus 12) 0.354,2.427 1.615,2.823 1.26,0.396 10 false Power Management Control ECU 1.01,3.26 2.469,3.469 1.458,0.208 10 false Serial Communication 0.281,3.635 1.667,4 1.385,0.365 10 false Inverter with Converter Assembly 0.219,4.99 1.75,5.365 1.531,0.375 10 false HV Coolant Temperature Sensor 0.688,4.354 1.302,4.542 0.615,0.188 10 false MG ECU 3.333,2.656 3.729,2.865 0.396,0.208 10 false ECM 3.885,1.052 4.302,1.25 0.417,0.198 10 false FANH 6.51,0.917 7.156,1.094 0.646,0.177 10 false EFI MAIN 6.521,1.26 6.948,1.438 0.427,0.177 10 false BATT 5.615,1.49 6.802,1.708 1.188,0.219 10 false Cooling Fan Relay 4.729,1.479 5.5,1.833 0.771,0.354 10 false Cooling Fan Motor 3.885,4.885 4.302,5.104 0.417,0.219 10 false FANL 6.542,4.417 6.958,4.594 0.417,0.177 10 false BATT 5.542,3 6.406,3.385 0.865,0.385 10 false No. 2 Cooling Fan Relay 5.583,5.01 6.458,5.406 0.875,0.396 10 false No. 3 Cooling Fan Relay 4.469,3.938 5.667,4.167 1.198,0.229 10 false Cooling Fan Motor 6.354,2.604 6.729,2.948 0.375,0.344 10 false EFI MAIN 6.521,4.76 7.156,4.948 0.635,0.188 10 false EFI MAIN

Air Conditioning Operating Condition Engine Coolant Temperature Hybrid System Coolant Temperature Relay Operation Cooling Fan Motor Connection Cooling Fan Operation
No. 1 No. 2 No. 3
Off Low Low Off Off Off Off Off
High Low On On On Parallel High
High High
A/C Pressure "Low" Low Low Off Off On Series Low
High Low On On On Parallel High
High High
A/C Pressure "High" High Low On On On Parallel High
High High


iii.

If coolant temperature is extremely high and ambient temperature is high when the power switch is turned off, the ECM operates the engine water pump assembly and cooling fan motors for maximum 3 minutes to ensure engine restartability.



c.

Water Pump Control

i.

Since this engine is stopped and restarted repeatedly by the hybrid system, by providing an electric engine water pump assembly, coolant temperatures while the engine is operating will be stable, and shutting off the power to the pump motor will contribute to fuel economy.


ii.

The ECM receives pump motor speed pulse signals from the electric water pump driver circuit, and then determines the pump motor speed so that an optimal engine coolant flow volume can be obtained according to the operating conditions.

W107895E04
3.417,1.094 4.5,1.281 1.083,0.188 10 false ENG W/P Relay 3.698,2.938 5.698,3.156 2,0.219 10 false Engine Water Pump Assembly 3.417,2.042 4.271,2.229 0.854,0.188 10 false Driver Circuit 0.083,2.115 1.281,2.333 1.198,0.219 10 false CAN (Sub Bus 12) 0.604,2.927 2.167,3.313 1.563,0.385 10 false Air Conditioning Amplifier Assembly 1.24,1.542 1.646,1.76 0.406,0.219 10 false ECM 2.51,1.375 2.896,1.552 0.385,0.177 10 false WPI 2.563,0.542 2.979,0.719 0.417,0.177 10 false BATT 1.948,0.865 3,1.073 1.052,0.208 10 false EFI MAIN Relay 2.479,1.844 2.865,2.021 0.385,0.177 10 false WPO 4.958,2.49 6.198,2.688 1.24,0.198 10 false Water Pump Motor



d.

Fuel Pump Control

i.

A fuel cut function is used to stop the fuel pump once when any of the SRS airbags have deployed. When the power management control ECU detects the airbag deployment signal from the airbag ECU assembly, it transmits an engine off signal to the ECM. Upon receiving this signal, the ECM turns off the circuit opening relay.


ii.

After the fuel cut function has been activated, turning the power switch from off to on cancels the fuel cut function, and the engine can be restarted.

W107896E03
3.729,3.052 3.906,3.052 3.906,3.052 4.115,2.479 false 0.219,0.635 1.531,0.854 1.313,0.219 10 false Front Airbag Sensor 2.177,0.979 3.656,1.208 1.479,0.229 10 false Airbag ECU Assembly 5.969,2.469 6.688,2.833 0.719,0.365 10 false Fuel Pump Motor 2.25,2.135 3.531,2.531 1.281,0.396 10 false Power Management Control ECU 3.01,1.615 3.917,1.813 0.906,0.198 10 false CAN (V Bus) 4.646,2.313 5.063,2.521 0.417,0.208 10 false ECM 5.99,1.281 6.979,1.646 0.99,0.365 10 false Circuit Opening Relay 5.25,2.365 5.5,2.563 0.25,0.198 10 false FC 2.51,2.958 3.719,3.156 1.208,0.198 10 false CAN (Sub Bus 12) 0.25,1.219 1.49,1.583 1.24,0.365 10 false Side Airbag Sensor Assembly 0.292,2.115 1.427,2.542 1.135,0.427 10 false Side No. 2 Airbag Sensor Assembly 6.271,0.417 6.865,0.792 0.594,0.375 10 false EFI Main Relay 4.927,0.438 5.219,0.667 0.292,0.229 10 false (IG)




FAIL-SAFE


a.

When a malfunction of any of the sensors is detected, there is a possibility of an engine or other malfunction occurring if the ECM were to continue normal control. To prevent such a problem, the fail-safe function of the ECM either relies on the data stored in memory to allow the engine control system to continue operating, or stops the engine if a hazard is anticipated. For details, refer to the Repair Manual.



DIAGNOSIS


a.

When the ECM detects a malfunction, the ECM records information related to the fault. Furthermore, the Malfunction Indicator Lamp (MIL) in the combination meter sub-assembly illuminates or blinks to inform the driver.


b.

The ECM will also store the Diagnostic Trouble Codes (DTCs) of the malfunctions. The DTCs can be accessed by using the Global TechStream (GTS).


c.

For details, refer to the Repair Manual.