Home › Engine / Hybrid System › 2ZR-FXE (INTAKE / EXHAUST) › INTAKE SYSTEM › from 2013.08
NM2070E _51 Engine / Hybrid System _061863 2ZR-FXE INTAKE / EXHAUST _0301398 INTAKE SYSTEM UN GENERAL/CONTROL/DETAILS F

2ZR-FXE INTAKE / EXHAUST  INTAKE SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


CONSTRUCTION


a.

Air Cleaner Assembly

i.

A paper type air cleaner filter element sub-assembly is used.

W109064E03
2.25,0.5 3.021,0.5 3.021,0.5 3.667,1.375 true 1.49,2.156 2.26,2.156 2.26,2.156 2.906,3.031 true 5.063,3.542 4.75,3.542 4.75,3.542 4.208,2.802 true 4.771,5.323 4.448,5.323 4.448,5.323 3.917,4.833 true 2.052,0.385 2.24,0.573 0.188,0.188 10 false *1 4.802,5.229 5.01,5.438 0.208,0.208 10 false *4 5.104,3.438 5.313,3.625 0.208,0.188 10 false *2 1.302,2.042 1.51,2.281 0.208,0.24 10 false *3

Text in Illustration
*1 Air Cleaner Cap Sub-assembly *2 Air Cleaner Filter Element Sub-assembly
*3 No.1 Air Cleaner Inlet
- Intake Air Resonator
*4 Air Cleaner Case Sub-assembly



b.

Throttle Body Assembly

i.

A linkless type throttle body assembly, in which the throttle position sensor and the throttle control motor are integrated, is used, realizing excellent throttle valve control.


ii.

A DC motor with excellent response and minimal power consumption is used for the throttle control motor. The ECM performs duty ratio control of the direction and the amperage of the current that flows to the throttle control motor in order to regulate the throttle valve angle.

W101512E11
3.542,0.917 2.927,0.323 2.927,0.323 2.802,0.323 true 4.677,1.885 5.323,1.052 5.323,1.052 5.427,1.052 true 4.125,2.333 4.563,3.354 4.563,3.354 4.688,3.354 true 2.385,2.813 2.01,3.438 2.01,3.438 1.906,3.438 true 2.615,0.229 2.813,0.427 0.198,0.198 10 false *1 1.719,3.344 1.917,3.542 0.198,0.198 10 false *2 5.479,0.948 5.677,1.146 0.198,0.198 10 false *3 4.74,3.26 4.938,3.479 0.198,0.219 10 false *4

Text in Illustration
*1 Throttle Control Motor *2 Throttle Position Sensor
*3 Throttle Valve *4 Return Spring



c.

Intake Manifold

i.

The intake manifold is made of plastic to reduce its weight and the amount of heat transferred from the cylinder head sub-assembly. As a result, it has become possible to reduce intake air temperature and realize high intake volumetric efficiency.


ii.

An EGR chamber is built into the intake manifold in order to uniformly distribute EGR gases to the cylinders.

W101563E04
5.229,1.219 6.292,2.458 6.292,2.458 6.385,2.458 true 2.906,1.875 3.667,0.833 3.667,0.833 3.771,0.833 true 2.271,2.469 3.052,3.042 3.052,3.042 3.146,3.042 true 1.219,3.083 1.885,3.479 1.885,3.479 1.979,3.479 true 2.073,1.208 2.781,0.333 2.781,0.333 2.906,0.333 true 2.938,0.219 3.156,0.427 0.219,0.208 10 false *1 3.813,0.729 4.031,0.938 0.219,0.208 10 false *2 3.177,2.948 3.396,3.156 0.219,0.208 10 false *3 2.01,3.375 2.229,3.583 0.219,0.208 10 false *4 6.417,2.365 6.635,2.573 0.219,0.208 10 false *5

Text in Illustration
*1 Intake Manifold *2 EGR Port
*3 PCV Port *4 Purge Port
*5 EGR Chamber - -