Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION SYSTEM › from 2016.05
NM2070E _53 Suspension _061870 FRONT SUSPENSION _0301409 FRONT SUSPENSION SYSTEM UN GENERAL/CONTROL/DETAILS F

FRONT SUSPENSION  FRONT SUSPENSION SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


CONSTRUCTION


a.

Front Suspension Support Sub-assembly and Front Coil Spring

i.

A split-input type structure is adopted for the front suspension support sub-assembly to ensure excellent quietness and ride comfort.


ii.

While driving, the input from the tires is transferred to the body via the front shock absorber assembly, front spring bumper and front coil spring. With a split-input type structure, the input from the front shock absorber assembly and front spring bumper is transferred to the body via the rubber portion of the front suspension support sub-assembly. The input from the front coil spring is transferred to the body via the strut mounting bearing. The input from the front shock absorber assembly and front spring bumper, and the input from the front coil spring are received separately, realizing excellent quietness and ride comfort.


iii.

A pigtail type front coil spring, where the top and bottom diameters are different is used creating a compact and lightweight construction. Lateral force reduction springs are used to control the reaction force line of the front coil spring, and reduce the bending force applied to the front shock absorber assembly. This reduces suspension friction, realizing a very comfortable ride.


iv.

A semi-airtight shock absorber dust cover which is attached to the absorber cap and moves with the shock absorber has been adopted. This reduces the gap between the shock absorber dust cover and shock absorber assembly, enhancing its ability to resist the intrusion of foreign matter.

X132051E02
3.115,0.469 2.885,0.125 2.885,0.125 2.688,0.125 true 2.479,0.583 2.302,0.333 2.302,0.333 2.135,0.333 true 2.802,2.344 2.292,2.344 true 3.365,3.229 2.323,3.229 true 5.26,1.74 3.76,1.74 true 5.25,2.292 4.042,2.292 true 4.042,0.708 4.406,0.188 4.406,0.188 4.729,0.188 true 2.917,0.875 2.563,1.25 2.563,1.25 2.24,1.25 true 3.354,0.927 2.76,1.563 2.76,1.563 2.24,1.563 true 3.5,1 2.823,1.875 2.823,1.875 2.24,1.875 true 2.104,2.208 2.26,2.385 0.156,0.177 10 false *3 2.125,3.135 2.281,3.313 0.156,0.177 10 false *4 5.302,2.198 5.458,2.375 0.156,0.177 10 false *5 5.313,1.625 5.521,1.844 0.208,0.219 10 false *6 4.802,0.083 4.958,0.26 0.156,0.177 10 false *7 2.5,0.021 2.729,0.208 0.229,0.188 10 false *1 1.927,0.229 2.146,0.427 0.219,0.198 10 false *2 2.01,1.135 2.167,1.313 0.156,0.177 10 false *a 2.021,1.438 2.177,1.615 0.156,0.177 10 false *b 2.01,1.74 2.167,1.917 0.156,0.177 10 false *c

Text in Illustration
*1 Front Suspension Support Sub-assembly *2 Body
*3 Front Coil Spring *4 Front Shock Absorber Assembly
*5 Shock Absorber Dust Cover *6 Front Spring Bumper
*7 Strut Mounting Bearing - -
*a Front Coil Spring Input *b Front Spring Bumper Input
*c Front Shock Absorber Assembly Input - -



b.

Front Shock Absorber Assembly

i.

Low-friction oil and oil seals are adopted for the front shock absorber assembly, ensuring damping responsiveness, and realizing a supple ride.


ii.

A low pressure N2 gas charge and saturated type piston valve is adopted for the front shock absorber assembly, contributing to a high level of maneuverability, stability and ride comfort.

X132028E02
3.323,1.125 6.417,4.167 3.094,3.042 1.927,1.802 2.146,1.396 2.146,1.396 2.344,1.396 true 1.594,1.521 1.365,1.115 1.365,1.115 1.167,1.115 true 1.469,3.052 1.188,3.052 true 1.719,3.656 1.208,3.656 true 1.469,4.24 1.198,4.24 true 4.365,2.76 4.094,3.292 4.094,3.292 3.865,3.292 true 5.375,2.271 5.594,1.771 5.594,1.771 5.792,1.771 true 1,1.01 1.188,1.198 0.188,0.188 10 false *1 2.375,1.292 2.604,1.51 0.229,0.219 10 false *5 1.031,2.958 1.229,3.177 0.198,0.219 10 false *2 1.031,3.563 1.24,3.75 0.208,0.188 10 false *3 1.031,4.135 1.24,4.344 0.208,0.208 10 false *4 3.427,1.188 3.656,1.417 0.229,0.229 10 false *a 4.125,1.719 4.323,1.917 0.198,0.198 10 false *b 3.698,3.188 3.917,3.385 0.219,0.198 10 false *d 5.458,3.094 5.625,3.292 0.167,0.198 10 false *c 5.823,1.667 6.031,1.875 0.208,0.208 10 false *d

Text in Illustration
*1 Oil Seal *2 Saturated Type Piston Valve
*3 Oil *4 Base Valve
*5 Low-pressure N2 Gas - -
*a Saturated Type Piston Valve Cross Section *b Extension
*c Compression *d Orifice

NOTICE:

To prevent hazardous conditions, make sure to empty the gas from the shock absorber before discarding an N2 gas sealed shock absorber. For details, refer to the Repair Manual.



iii.

The characteristics of saturated type piston valve are as follows:

1.

The orifices are tuned to optimize body control in the low speed (piston speed) damping range.

2.

Valve preload is tuned to optimize control of vehicle body movement in the mid speed (piston speed) damping range.

3.

The oil passages in the piston have been enlarged to decrease the damping force, thereby reducing the shocks due to impacts in the high speed (piston speed) damping range.


X105750E03
3.5,1.063 3.219,0.427 3.219,0.427 3.073,0.427 true 4.073,1.073 4.406,0.219 4.406,0.219 4.573,0.219 true 5.448,1.063 5.75,0.729 5.75,0.729 5.896,0.729 true 0.833,0.76 2.292,1.031 1.458,0.271 10 false : Linear Control Valve 1.438,1.74 3.083,1.958 1.646,0.219 10 false Extension Damping Force 1.896,0.313 3.052,0.5 1.156,0.188 10 false Low Piston Speed 0.833,1.031 2.708,1.302 1.875,0.271 10 false : Saturated Type Piston Valve 1.25,2.656 3.063,2.854 1.813,0.198 10 false Compression Damping Force 4.615,0.115 5.771,0.333 1.156,0.219 10 false Mid Piston Speed 5.927,0.615 7.146,0.833 1.219,0.219 10 false High Piston Speed 5.469,2.469 6.417,2.677 0.948,0.208 10 false Piston Speed



c.

Front Lower Suspension Arm Sub-assembly

i.

An L-shaped front lower No. 1 suspension arm sub-assembly, of which the cross section structure is closed, is provided. As a result, in addition to the material thickness having been made thinner, the cross section and arm shape have been optimized, thus, achieving a lightweight yet highly rigid design.


ii.

The installation point of the lower arm bushes and the bushing characteristics have been optimized to achieve excellent ride comfort and steering characteristics.

X101570E06
2.427,1.125 2.833,0.719 2.833,0.719 3.021,0.719 true 4.646,1.542 4.135,1.021 4.135,1.021 3.875,1.021 true 3.063,0.615 3.292,0.948 0.229,0.333 10 false *4 3.698,0.854 3.875,1.188 0.177,0.333 10 false *1 2.823,2.688 3.083,2.948 0.26,0.26 10 false *2 0.281,0.292 0.542,0.552 0.26,0.26 10 false *a 4.896,2.219 5.146,2.406 0.25,0.188 10 false *3 2.427,1.875 2.583,2.052 0.156,0.177 10 false A 3.406,1.354 3.563,1.531 0.156,0.177 10 false A

Text in Illustration
*1 Front Lower No. 1 Suspension Arm Sub-assembly *2 Front Lower No. 1 Arm Bush (Cross Section)
*3 Front Lower No. 2 Arm Bush (Cross Section) *4 Front Lower Ball Joint Assembly
*a A-A Cross Section - -
V100135

Front - -



d.

Front Stabilizer Bar

i.

The front stabilizer bar is hollow, reducing weight. A ball joint is used between the front stabilizer link assembly and the front stabilizer bar, and between the front stabilizer link assembly and the front shock absorber assembly. This helps reduce suspension friction and increase link rigidity. As a result, the ball joints perform effectively even for small amounts of roll and maintain stable roll feeling.


ii.

An aluminum front stabilizer link assemblies are used to achieve weight reduction.


iii.

To reduce friction, a fluorine coating is provided in the bore of the front stabilizer bar bush.


iv.

The front stabilizer bar bush is provided with a dust lip to prevent sand from entering.

X136813E01
2.135,1.813 2.927,1.021 2.927,1.021 3.042,1.021 true 4.448,3.344 5.552,2.198 5.552,2.198 5.667,2.198 true 4.479,3.542 5.865,3.542 true 2.385,3.323 2.479,3.323 2.479,3.323 3.281,2.99 true 1.646,4.292 1.74,4.292 1.74,4.292 1.865,4.521 true 3.083,0.927 3.396,1.125 0.313,0.198 10 false *1 5.708,2.104 6.021,2.302 0.313,0.198 10 false *3 2.219,3.219 2.531,3.417 0.313,0.198 10 false *3 5.885,3.438 6.198,3.635 0.313,0.198 10 false *2 1.479,4.198 1.792,4.396 0.313,0.198 10 false *a

Text in Illustration
*1 Front Stabilizer Link Assembly *2 Front Stabilizer Bar
*3 Front Stabilizer Bar Bush - -
*a Dust Lip - -
V100136

Outside of the Vehicle - -

NOTICE:

To install the front stabilizer bar bushes on the vehicle, face the dust lips outward.




e.

Front Suspension Crossmember Sub-assembly

i.

A pressed-steel front suspension crossmember sub-assembly is provided.

X109136E02
3.26,5.115 3.26,4.063 true 3.188,5.135 3.375,5.323 0.188,0.188 10 false *1

Text in Illustration
*1 Front Suspension Crossmember Sub-assembly - -