Home › Suspension › REAR SUSPENSION › REAR SUSPENSION SYSTEM
NM2070E _53 Suspension _061871 REAR SUSPENSION _0301410 REAR SUSPENSION SYSTEM UN GENERAL/CONTROL/DETAILS F

REAR SUSPENSION  REAR SUSPENSION SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


CONSTRUCTION


a.

Rear Coil Spring and Rear Shock Absorber Assembly

i.

Both ends of the coil spring are formed into a small-diameter, pigtail shape. The compact construction is designed to accommodate the low floor package.


ii.

Spring insulators are provided at the top and bottom ends of the rear coil springs, and the thickness of the insulators is optimized to reduce vibration and achieve excellent ride comfort.


iii.

Low-pressure N2 gas sealed rear shock absorber assemblies deliver stable damping force characteristics, providing excellent maneuverability and ride comfort.

X105774E03
1.885,1.115 1.365,0.594 1.365,0.594 1.135,0.594 true 2.5,0.927 2.969,0.281 2.969,0.281 3.167,0.281 true 1.979,2.167 1.521,2.635 1.521,2.635 1.323,2.635 true 1.698,1.823 1.25,2.292 1.25,2.292 1.052,2.292 true 4.01,2.406 4.552,2.76 4.552,2.76 4.781,2.76 true 4.042,1.25 3.719,0.656 3.719,0.656 3.583,0.656 true 4.073,1.938 4.677,1.573 4.677,1.573 4.927,1.573 true 0.969,0.49 1.167,0.688 0.198,0.198 10 false *1 3.208,0.188 3.406,0.385 0.198,0.198 10 false *2 1.146,2.552 1.344,2.75 0.198,0.198 10 false *3 0.885,2.198 1.083,2.396 0.198,0.198 10 false *4 4.854,2.635 5.052,2.833 0.198,0.198 10 false *5 3.417,0.563 3.615,0.76 0.198,0.198 10 false *6 4.99,1.479 5.188,1.677 0.198,0.198 10 false *7

Text in Illustration
*1 Rear Coil Spring *2 Rear Upper Coil Spring Insulator
*3 Rear Lower Coil Spring Insulator *4 Coil Spring Seat
*5 Rear Shock Absorber Assembly *6 Rear Suspension Support
*7 Dust Cover - -

NOTICE:

To prevent hazardous conditions, make sure to empty the gas from the shock absorber before discarding an N2 gas sealed shock absorber. For details, refer to the Repair Manual.




b.

Axle Beam and Trailing Arm

i.

The axle beam offers not only high rigidity but also stability due to optimization of the shear center.


ii.

The trailing arms are secured to the body via angled rear axle carrier bushes.

X105775E02
3.865,4.188 3.042,5 3.042,5 2.781,5 true 4.844,4.854 5.229,5.354 5.229,5.354 5.354,5.354 true 2.448,3.76 1.635,4.583 1.635,4.583 1.375,4.583 true 2.646,1.563 2.885,1.958 2.885,1.958 2.958,1.958 true 0.563,0.49 0.781,0.698 0.219,0.208 10 false *a 2.615,4.906 2.833,5.083 0.219,0.177 10 false *1 5.396,5.26 5.615,5.438 0.219,0.177 10 false *2 1.208,4.49 1.427,4.667 0.219,0.177 10 false *3 2.99,1.854 3.208,2.031 0.219,0.177 10 false *2

Text in Illustration
*1 Axle Beam (Rear Axle Beam Assembly) *2 Trailing Arm (Rear Axle Beam Assembly)
*3 Rear Axle Carrier Bush - -
*a Cross Section - -
V100135

Front - -