Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2012.03–2014.11
NM2070E _58 Vehicle Interior _061890 PRE-CRASH SAFETY _0301434 PRE-CRASH SAFETY SYSTEM UN GENERAL/CONTROL/DETAILS F

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


Item Function
Combination Meter Sub-assembly PCS Warning Light
·

Illuminates or flashes to warn the driver in accordance with signals from the seat belt control ECU or driving support ECU assembly.

·

Illuminates or flashes when the system is malfunctioning or temporarily disabled.


Millimeter Wave Radar Sensor Assembly Radiates millimeter wave radar forward, uses the reflected millimeter waves for detecting the presence of a vehicle ahead, the vehicle-to-vehicle distance, and the relative speed, and then transmits this information to the driving support ECU assembly.
Front Seat Outer Belt Assembly Seat Belt Motor Retracts the seat belt in accordance with signals received from the seat belt control ECU.
Front Seat Inner Belt Assembly (for Driver) Buckle Switch Detects the condition (verifies if the belt is fastened) of the driver seat belt and transmits a signal to the seat belt control ECU.
Front Seat Inner Belt Assembly (for Front Passenger) Buckle Switch Detects the condition (verifies if the belt is fastened) of the front passenger seat belt and transmits a signal to the seat belt control ECU.
Driving Support ECU Assembly Makes judgments on whether a collision is possible based on the information received from the millimeter wave radar sensor assembly. It then outputs a seat belt operation signal and brake assist standby request signal and pre-crash brake request signal if required.
Seat Belt Control ECU Receives a seat belt operation request signal from the driving support ECU assembly or skid control ECU and operates the seat belts.
Headup Display Unit (Combination Meter Mirror ECU)* Displays a warning message on the windshield to inform or warn the driver of the system condition in accordance with signals from the driving support ECU assembly.
Brake Booster Pump Assembly Receives an operation signal from the skid control ECU and generates hydraulic pressure for brake control.
Brake Booster with Master Cylinder Assembly Master Cylinder Pressure Sensor Detects the master cylinder pressure and transmits a signal to the skid control ECU.
Skid Control ECU
·

Receives a brake assist standby request signal from the driving support ECU assembly and switches the brake assist to standby mode. When a stop light switch signal is input, it activates the brake assist.

·

Receives a pre-crash brake request signal from the driving support ECU assembly, and then applies the brakes.

·

Determines if the brakes have been applied suddenly through signals received from the master cylinder pressure sensor, and outputs a seat belt operation signal to the seat belt control ECU.

·

Determines that the vehicle is out of control or that the brakes have been applied and outputs a seat belt operation signal to the seat belt control ECU.

·

Transmits vehicle speed signals to the driving support ECU assembly.


Stop Light Switch Detects if the brake pedal is depressed and transmits a signal to the skid control ECU.
Stop Light Control ECU Assembly Receives a stop light turn on request signal from the skid control ECU, and turns on the stop lights.
Speed Sensor Detects speed of each wheel and transmits the signals to the skid control ECU.
Yawrate Sensor Detects the yaw rate and lateral/longitudinal deceleration of the vehicle and transmits the signal to the skid control ECU and the driving support ECU assembly.
Spiral Cable with Sensor Sub-assembly
- Steering Angle Sensor
Detects the angle and direction of steering and transmits a signal to the skid control ECU and the driving support ECU assembly.
Pre-crash System Cancel Switch Assembly Disables the pre-crash brake operation when the switch is turned on. The PCS warning light illuminates to show that the pre-crash brake operation is disabled.
Skid Control Buzzer Assembly Sounds to warn the driver in accordance with signals from the skid control ECU.

*: Models with Headup Display


OPERATING CONDITION


a.

Operating Conditions

Operating Conditions When the driving support ECU assembly determines the high possibility of a collision, or an unavoidable collision with an obstacle in front of the vehicle.
The pre-crash seat belt also operates under the following conditions:
·

When the brakes are suddenly applied.


·

When the system determines a loss of vehicle control.




b.

The following pre-crash safety system controls are performed under the following conditions.

Control Condition
Pre-crash Seat Belt (Situation 1)
·

Front seat belt is buckled.


·

Vehicle speed is approximately 30 km/h (19 mph) or above.


·

Brakes are suddenly applied, or front or rear wheel skid tendency is detected.


Pre-crash Seat Belt (Situation 2)
·

Front seat belt is buckled.


·

Vehicle speed is approximately 5 km/h (3 mph) or above.


·

Oncoming vehicle or an obstacle relative speed is approximately 30 km/h (19 mph) or above.


Pre-crash Brake Assist
·

Vehicle speed is approximately 30 km/h (19 mph) or above.


·

Oncoming vehicle or an obstacle relative speed is approximately 30 km/h (19 mph) or above.


·

Brake pedal is depressed.


Pre-crash Brake
·

Pre-crash brake operation has not been disabled using pre-crash system cancel switch assembly.


·

Vehicle speed is approximately 15 km/h (10 mph) or above.


·

Oncoming vehicle or an obstacle relative speed is approximately 15 km/h (10 mph) or above.





SYSTEM CONTROL


a.

Loss of Vehicle Control

(1) While the vehicle is traveling at approximately 30 km/h (19 mph) or more, the skid control ECU determines if skid recovery will be difficult based on the signals from the steering angle sensor, yawrate sensor and speed sensors.
(2) The skid control ECU sends a seat belt operation request signal to the seat belt control ECU.
(3) The seat belt control ECU determines the seat belt motor operating conditions based on this signal and seat belt buckle switch signals. Then, it retracts the slack in the seat belts by operating the seat belt motors.
(4) The seat belts return to a normal state when the relevant conditions of the vehicle have stabilized.

Y118869E02
1.927,0.813 2.729,1.208 0.802,0.396 10 false Skid Control ECU 0.563,1.01 1.531,1.24 0.969,0.229 10 false Speed Sensor 2.313,2.792 3.51,2.979 1.198,0.188 10 false CAN (Sub Bus 11) 3.729,1.875 4.656,2.104 0.927,0.229 10 false CAN (V Bus) 5.469,0.958 6.927,1.156 1.458,0.198 10 false Steering Angle Sensor 5.604,1.5 6.708,1.708 1.104,0.208 10 false Yawrate Sensor 4.802,3.26 6.771,3.594 1.969,0.333 10 false Front Seat Inner Belt Assembly (for Driver) 5.365,3.958 6.365,4.292 1,0.333 10 false Buckle Switch 4.813,4.51 6.771,4.833 1.958,0.323 10 false Front Seat Inner Belt Assembly (for Front Passenger) 5.313,5.24 6.354,5.573 1.042,0.333 10 false Buckle Switch 0.49,3.25 2.479,3.563 1.99,0.313 10 false Front Seat Outer Belt Assembly (for Driver) 0.927,3.958 1.979,4.292 1.052,0.333 10 false Seat Belt Motor 0.5,4.521 2.5,4.854 2,0.333 10 false Front Seat Outer Belt Assembly (for Front Passenger) 0.938,5.24 1.979,5.573 1.042,0.333 10 false Seat Belt Motor 1.552,1.188 1.802,1.406 0.25,0.219 10 false (1) 3.063,0.771 3.26,0.99 0.198,0.219 10 false (1) 4.917,1.302 5.167,1.521 0.25,0.219 10 false (1) 4.927,1.865 5.177,2.063 0.25,0.198 10 false (1) 4.333,4.167 4.552,4.5 0.219,0.333 10 false (3) 2.646,4.156 3.104,4.365 0.458,0.208 10 false (3), (4) 2.646,5.427 3.104,5.625 0.458,0.198 10 false (3), (4) 4.313,5.427 4.573,5.635 0.26,0.208 10 false (3) 2.958,1.323 3.198,1.542 0.24,0.219 10 false (2) 3.188,3.813 4.01,4.573 0.823,0.76 10 false Seat Belt Control ECU 2.563,2.208 4.677,2.427 2.115,0.219 10 false Power Management Control ECU 3.813,2.802 4.292,2.99 0.479,0.188 10 false (2) 5.406,0.26 6.958,0.646 1.552,0.385 10 false Spiral Cable with Sensor Sub-assembly 1.542,1.521 3.24,1.875 1.698,0.354 10 false Brake Booster with Master Cylinder Assembly


b.

Sudden Braking

(1) While the vehicle is traveling at approximately 30 km/h (19 mph) or more, the skid control ECU can determine a sudden braking condition based on the signals from the master cylinder pressure sensor, stop light switch and speed sensors.
(2) At this time, the skid control ECU outputs a seat belt operation request signal to the seat belt control ECU.
(3) The seat belt control ECU determines the seat belt motor operating conditions based on this signal and seat belt buckle switch signals. Then, it retracts the slack in the seat belts by operating the seat belt motors.
(4) The seat belts return to normal when the vehicle stops and the brake pedal is released.

Y121472E02
0.75,0.198 1.865,0.427 1.115,0.229 10 false Stop Light Switch 1.969,0.74 2.198,0.917 0.229,0.177 10 false (1) 1.969,0.323 2.198,0.5 0.229,0.177 10 false (1) 3.385,0.875 3.656,1.073 0.271,0.198 10 false (2) 4.323,1.906 5.26,2.146 0.938,0.24 10 false CAN (V Bus) 0.938,0.604 1.854,0.823 0.917,0.219 10 false Speed Sensor 0.25,1.063 1.844,1.438 1.594,0.375 10 false Master Cylinder Pressure Sensor 0.427,1.917 1.771,2.302 1.344,0.385 10 false Brake Booster Pump Assembly 2.281,2.448 3.49,2.854 1.208,0.406 10 false Brake Booster with Master Cylinder 2.542,0.854 3.135,1.385 0.594,0.531 10 false Skid Control ECU 5.667,5.052 6.615,5.271 0.948,0.219 10 false Buckle Switch 5.667,6.229 6.615,6.479 0.948,0.25 10 false Buckle Switch 3.781,5.042 4.583,5.51 0.802,0.469 10 false Seat Belt Control ECU 5.125,4.333 7.083,4.646 1.958,0.313 10 false Front Seat Inner Belt Assembly (for Driver) 5.115,5.521 7.063,5.906 1.948,0.385 10 false Front Seat Inner Belt Assembly (for Front Passenger) 2.875,3.969 4.073,4.198 1.198,0.229 10 false CAN (Sub Bus 11) 4.427,4 4.698,4.24 0.271,0.24 10 false (2) 3.188,5.25 3.677,5.448 0.49,0.198 10 false (3), (4) 3.198,6.427 3.688,6.635 0.49,0.208 10 false (3), (4) 4.833,6.427 5.052,6.667 0.219,0.24 10 false (3) 3.521,3.146 4.823,3.51 1.302,0.365 10 false Power Management Control ECU 1.521,5.052 2.552,5.281 1.031,0.229 10 false Seat Belt Motor 1,4.354 3,4.74 2,0.385 10 false Front Seat Outer Belt Assembly (for Driver) 1.01,5.521 3.01,5.948 2,0.427 10 false Front Seat Outer Belt Assembly (for Front Passenger) 1.5,6.229 2.521,6.427 1.021,0.198 10 false Seat Belt Motor 4.854,5.24 5.073,5.479 0.219,0.24 10 false (3)


c.

High Possibility of Collision or Unavoidable Collision

(1) The driving support ECU assembly determines that the possibility of a collision is high based on the signals received from the millimeter wave radar sensor assembly, steering angle sensor, speed sensor and yawrate sensor.
(2) The driving support ECU assembly transmits a PCS warning display request signal to the combination meter sub-assembly and a skid control buzzer assembly request signal to the skid control ECU.
(3) The driving support ECU assembly outputs a pre-crash brake assist request signal to the skid control ECU. Upon receiving this signal, the skid control ECU switches the brake assist to the standby condition and sounds the skid control buzzer assembly to warn the driver. At this time, the skid control ECU activates pre-crash brake assist when the brake pedal is depressed by the driver.
(4) The driving support ECU assembly determines that an unavoidable collision condition exists based on the signals received from the millimeter wave radar sensor assembly, speed sensor, steering angle sensor and yawrate sensor.
(5) The driving support ECU assembly outputs a seat belt operation request signal to the seat belt control ECU and a pre-crash brake request signal to the skid control ECU.
(6) The seat belt control ECU determines the seat belt motor operation condition based on this signal and the seat belt buckle switch signal, and retracts the slack in the seat belts by operating the seat belt motors. At the same time, the skid control ECU decreases the vehicle speed by activating the brake actuator and brake booster pump assembly to perform a pre-crash brake operation, activates the stop light control relay to turn on the stop lights, and sounds the skid control buzzer assembly to warn the driver.
(7) If no collision occurs, the seat belts and brake assist will return to their normal states.

Y118871E02
0.385,0.74 1.844,1.146 1.458,0.406 10 false Millimeter Wave Radar Sensor Assembly 2.01,0.74 3.438,0.958 1.427,0.219 10 false Serial Communication 4.479,1.354 5.729,1.583 1.25,0.229 10 false CAN (Sub Bus 11) 2.552,0.552 3.073,0.802 0.521,0.25 10 false (1), (4) 2.313,4.885 2.75,5.135 0.438,0.25 10 false (6), (7) 2.292,6.125 2.75,6.406 0.458,0.281 10 false (6), (7) 2.208,7.375 2.667,7.625 0.458,0.25 10 false (1), (4) 3.969,7.313 4.719,7.51 0.75,0.198 10 false (3), (6), (7) 2.385,2.417 2.604,2.75 0.219,0.333 10 false (6) 2.375,3.635 2.635,3.885 0.26,0.25 10 false (6) 3.76,6.708 4.5,7.094 0.74,0.385 10 false (2), (3), (5), (6), (7) 4.104,7.781 4.563,7.99 0.458,0.208 10 false (3), (6) 4.229,8.24 4.49,8.5 0.26,0.26 10 false (6) 2.354,6.99 2.615,7.198 0.26,0.208 10 false (3) 4.573,0.927 5.073,1.167 0.5,0.24 10 false (1), (4) 4.719,5.771 5.167,6.104 0.448,0.333 10 false (1), (4) 4.74,6.698 5.219,6.927 0.479,0.229 10 false (1), (4) 3.458,0.802 4.198,1.156 0.74,0.354 10 false (2), (3), (5), (6), (7) 4.792,3.167 5,3.385 0.208,0.219 10 false (2) 3.604,1.438 4.125,1.677 0.521,0.24 10 false (5), (7) 4.521,4.26 5.458,4.594 0.938,0.333 10 false CAN (V Bus) 0.125,3.99 2.125,4.396 2,0.406 10 false Front Seat Outer Belt Assembly (for Driver) 0.146,5.229 2.156,5.615 2.01,0.385 10 false Front Seat Outer Belt Assembly (for Front Passenger) 0.594,5.938 1.698,6.135 1.104,0.198 10 false Seat Belt Motor 0.563,4.677 1.604,4.906 1.042,0.229 10 false Seat Belt Motor 1.063,6.885 2.188,7.094 1.125,0.208 10 false Stop Light Switch 1.188,7.24 2.167,7.458 0.979,0.219 10 false Speed Sensors 0.219,7.75 1.813,8.125 1.594,0.375 10 false Master Cylinder Pressure Sensor 5.031,7.115 7.01,7.333 1.979,0.219 10 false Brake Booster Pump Assembly 5.073,7.573 6.969,7.792 1.896,0.219 10 false Skid Control Buzzer Assembly 2.833,6.99 3.635,7.344 0.802,0.354 10 false Skid Control ECU 5.24,8.042 6.865,8.25 1.625,0.208 10 false Stop Light Control Relay 4.229,1.74 5.5,2.156 1.271,0.417 10 false Power Management Control ECU 5.417,5.365 6.948,5.594 1.531,0.229 10 false - Steering Angle Sensor 0.677,3.458 1.646,3.667 0.969,0.208 10 false Buckle Switch 0.677,2.219 1.646,2.406 0.969,0.188 10 false Buckle Switch 5.625,6.323 6.656,6.542 1.031,0.219 10 false Yawrate Sensor 2.833,3.521 3.646,4.177 0.813,0.656 10 false Seat Belt Control ECU 5.479,3.021 6.698,3.448 1.219,0.427 10 false Combination Meter Sub-assembly 5.469,3.708 6.823,3.938 1.354,0.229 10 false - PCS Warning Light 0.167,2.74 2.146,3.167 1.979,0.427 10 false Front Seat Inner Belt Assembly (for Front Passenger) 0.146,1.5 2.135,1.938 1.99,0.438 10 false Front Seat Inner Belt Assembly (for Driver) 3.698,0.115 5.01,0.458 1.313,0.344 10 false Driving Support ECU Assembly 1.865,8.531 4.74,8.771 2.875,0.24 10 false Brake Booster with Master Cylinder Assembly 5.375,4.656 6.927,5.042 1.552,0.385 10 false Spiral Cable with Sensor Sub-assembly 3.771,6.094 4.229,6.302 0.458,0.208 10 false (1), (4)



FUNCTION


a.

Warning displayed in combination meter sub-assembly

i.

The combination meter sub-assembly uses the PCS warning light and buzzer to provide the driver with pre-crash safety system warnings and indications.


ii.

If the driving support ECU assembly determines that the possibility of a collision is high, it sends a signal to the combination meter sub-assembly. Upon receiving this signal, the combination meter sub-assembly operates the PCS warning light.




CONSTRUCTION


a.

Millimeter Wave Radar Sensor Assembly

i.

The millimeter wave radar sensor assembly consists of a millimeter wave radar circuit, signal processing circuit and CPU.


ii.

The millimeter wave radar outputs waves when the vehicle speed is above 0 km/h (0 mph), and not when the vehicle speed is at 0 km/h (0 mph). The millimeter wave radar uses frequencies in the 76 GHz band.


iii.

The reception antennas receive the millimeter wave radar waves that have been reflected.


iv.

The signal processing circuit detects the distance, relative speed, and the direction of the object by generating millimeter wave radar waves and calculating the signals received by the reception antennas. Then, it transmits this information to the driving support ECU assembly.

Y110500E01
4.649,4.08 4.916,4.283 0.267,0.202 10 *1 4.714,3.296 4.714,4.043 false 2.295,4.439 2.551,4.614 0.255,0.175 10 *a 3.609,3.992 3.865,4.167 0.255,0.175 10 *b 1.734,3.502 1.990,3.677 0.255,0.175 10 *c 2.827,1.175 3.082,1.350 0.255,0.175 10 *d 1.996,0.031 2.252,0.206 0.255,0.175 10 *e

Text in Illustration
*1 Millimeter Wave Radar Sensor Assembly - -
*a Detection Distance: Approximately 150 m (490 ft.) *b Horizontal Angle: Approximately 20°
*c Vertical Angle: Approximately 8° *d Signal Processing Circuit
*e Millimeter Wave Radar Circuit - -


v.

The distance to the object, azimuth and relative speed are calculated from the information that is provided by the reflection millimeter wave radar as described below.

Item Calculation Method
Distance Calculated from the length of time that has elapsed from the time the waves of the millimeter wave radar have been emitted, until the waves reflected by the millimeter wave radar are received. The detection distance is approximately 150 m (490 ft.).
Azimuth Calculated from the angle of the waves reflected by the millimeter wave radar that have been received. The detection angle has a horizontal angle of approximately 20° and a vertical angle of approximately 8°.
Relative Speed Calculated by utilizing the changes (Doppler effect*) that occur in the frequencies of the reflected millimeter wave radar waves.

HINT:

*: The Doppler effect causes the observer to perceive the radio waves emitted by a moving object to be a higher frequency as it approaches, and to be a lower frequency as it recedes. This phenomenon is created because when an object is located far away, the radio waves are perceived at higher frequency than those of the radio source.


Y102750E34
3.51,1.25 3.625,0.844 3.625,0.844 3.781,0.844 true 1.667,0.865 1.729,0.615 1.729,0.615 1.823,0.615 true 5.333,0.854 5.396,0.604 5.396,0.604 5.49,0.604 true 2.99,1.906 3.104,2.344 3.104,2.344 3.292,2.344 true 3.313,3.344 3.771,3.344 false 1.865,0.479 3.333,0.698 1.469,0.219 10 false A: Own Vehicle Speed 5.823,1.354 6.75,1.656 0.927,0.302 10 false Target Vehicle 0.375,1.344 1.219,1.542 0.844,0.198 10 false Own Vehicle 5.521,0.49 7.063,0.729 1.542,0.24 10 false B: Target Vehicle Speed 3.823,0.74 4.708,0.958 0.885,0.219 10 false F: Frequency 3.333,2.24 5.552,2.49 2.219,0.25 10 false F': Frequency due to Doppler Effect 3.833,3.25 4.073,3.458 0.24,0.208 10 false x F 3.031,3.26 3.302,3.469 0.271,0.208 10 false F' = 3.375,3.146 3.75,3.333 0.375,0.188 10 false V + B 3.396,3.375 3.792,3.563 0.396,0.188 10 false V - A 1.167,2.74 6.135,2.969 4.969,0.229 10 false By applying the following formula, the target vehicle speed B can be calculated. 4.375,3.396 5.406,3.729 1.031,0.333 10 false V: Wave Speed

HINT:
·

Millimeter wave radar uses an extremely high frequency band between 30 GHz and 300 GHz, with an extremely short wavelength between 1 and 10 mm (0.04 to 0.40 in.) in a vacuum. The millimeter wave radar sensor of the pre-crash safety system uses frequencies in the 76 GHz band.

·

Millimeter wave radar is less affected by weather conditions such as rain, fog, or snow, and provides excellent characteristics for recognizing objects. Therefore, it is well suited to the pre-crash safety system and the dynamic radar cruise control system.

·

An SST is used if radar axis adjustment is needed. For details, refer to the Repair Manual.



Y100240E34
2.25,1.083 2.25,1.615 true 3.781,1.083 3.781,1.615 true 4.542,1.083 4.542,1.615 true 6.031,1.083 6.031,1.615 true 0.552,1 0.927,1.177 0.375,0.177 10 false Type 0.542,0.49 1.229,0.667 0.688,0.177 10 false Frequency 1.167,0.979 1.844,1.219 0.677,0.24 10 false Long wave 4.917,0.99 5.635,1.188 0.719,0.198 10 false Micro wave 1.99,1.635 2.646,1.802 0.656,0.167 10 false AM Radio 3.51,1.635 4.167,1.802 0.656,0.167 10 false FM Radio 4.26,1.635 5.208,1.979 0.948,0.344 10 false Cellular Mobile Phone 2.646,0.979 3.375,1.146 0.729,0.167 10 false Short wave 1.719,0.5 2.281,0.677 0.563,0.177 10 false 200 kHz 2.521,0.5 2.979,0.677 0.458,0.177 10 false 2 MHz 4.844,0.5 5.302,0.677 0.458,0.177 10 false 2 GHz 5.51,0.5 6.01,0.677 0.5,0.177 10 false 30 GHz 3.271,0.5 3.771,0.677 0.5,0.177 10 false 25 MHz 3.979,0.5 4.563,0.677 0.583,0.177 10 false 300 MHz 6.25,0.5 6.833,0.677 0.583,0.177 10 false 300 GHz 5.573,1.625 7.01,1.99 1.438,0.365 10 false Millimeter Wave Radar Sensor (76 GHz)



b.

Warning Indication

i.

The combination meter assembly uses the headup display, PCS warning light and buzzer to provide the driver with pre-crash safety system warnings and indications.


ii.

If the driving support ECU assembly determines that there is a possibility of a collision, it sends a signal to the combination meter assembly. Upon receiving this signal, the combination meter assembly indicates a warning using the headup display, PCS warning light and skid control buzzer assembly. Details are indicated below.

When there is a high possibility of a collision
Headup Display PCS Warning Light Skid Control Buzzer Assembly
Y121473

Flashes Sounds Continuously

When there is a high possibility of a collision
Headup Display PCS Warning Light Skid Control Buzzer Assembly
Y122871

Flashes Sounds Continuously


iii.

When the system is not available, the following warning occurs to warn the driver.

When a system malfunction is detected
Warning Detail Master Warning Light PCS Warning Light Buzzer DTC
Check PCS system The seat belt control ECU or the driving support ECU assembly detects a system malfunction. Illuminates Flashes Sounds once Repair is required
DTCs are stored
PCS system is not currently available

The seat belt control ECU or the driving support ECU assembly determines any of the following conditions exists:

-

Dirty millimeter wave radar sensor assembly

-

Poor weather condition

-

Overheated seat belt control ECU



After the condition has been resolved, the system will operate normally.
- Illuminates - -




DIAGNOSIS


a.

Initial Check

i.

The seat belt control ECU performs an initial check on the system for approximately 3 seconds after the power switch has been turned on (IG).



b.

Monitor Function

i.

After completing the initial check, the pre-crash safety system becomes ready to operate. During this time, the seat belt control ECU periodically monitors the system for any malfunctions.



c.

Diagnostic Trouble Code (DTC)

i.

If the seat belt control ECU or the driving support ECU assembly detects a malfunction in the pre-crash safety system, it stores a 5 digit Diagnostic Trouble Code (DTC) in memory.