FUNCTION OF MAIN COMPONENTS
| Components | Function | |
|---|---|---|
| Forward Recognition Camera | ·
Captures a view of the road ahead of the vehicle and detects lane markers on the driving lane, and calculates the radius to the center of the lane, lane width, distance from markers and heading angle deviation. ·
Transmits the indicator illumination request signal, multi-information display indication request signal, and buzzer sound request signal to the combination meter assembly. ·
Receives vehicle information and turn signal light operation signals and sends a steering force signal to the power steering ECU assembly. ·
Controls the LDA system. |
|
| Camera Heater (Forward Recognition Hood with Heater Sub-assembly) | Heats the sheet heater in accordance with the signals from the forward recognition camera. | |
| Millimeter Wave Radar Sensor Assembly | Radiates millimeter waves forward, uses the reflected waves to detect the presence of a vehicle traveling ahead and then transmits this information to the forward recognition camera. | |
| Driving Support ECU Assembly | Transmits the LDA main switch signal to the forward recognition camera. | |
| Combination Meter Sub-assembly | Transmits a turn signal command to the forward recognition camera. | |
| Combination Meter Sub-assembly | ·
LDA Indicator Light ·
Steering Indicator Light |
Illuminates or turns off in accordance with signals from the forward recognition camera. |
| Multi-information Display | Displays a warning message and white lines to inform or warn the driver of the system condition in accordance with signals from the forward recognition camera. | |
| Master Warning Light | Illuminates to warn the driver in accordance with signals from the forward recognition camera. | |
| Buzzer | Sounds to warn the driver in accordance with signals from the forward recognition camera. | |
| Hybrid Vehicle Control ECU | ·
Sends the accelerator pedal opening angle signal to the forward recognition camera. ·
Sends the shift position signal to the forward recognition camera. |
|
| Headlight Dimmer Switch Assembly | Transmits a turn signal command to the combination meter sub-assembly. | |
| Brake Booster with Master Cylinder Assembly | Skid Control ECU | Sends a vehicle speed signal from the speed sensor to the forward recognition camera. |
| Integration Control and Panel Assembly | LDA Main Switch | Detects an on/off status of the system and transmits a signal to the driving support ECU assembly. |
| Steering Pad Switch Assembly | Meter Control Switch | Changes the customize settings of the lane departure alert function, steering assist function and vehicle sway warning function. |
| Airbag ECU Assembly | Yawrate Sensor | Detects yaw rate and transmits a signal to the forward recognition camera. |
| Spiral Cable with Sensor Sub-assembly | Steering Sensor | Detects the angle and direction of steering and transmits signals to the forward recognition camera. |
| Power Steering ECU Assembly | ·
Controls the power steering motor assembly according to signals from the forward recognition camera. ·
Sends steering torque signals from the torque sensor to the forward recognition camera. ·
Detects steering operations performed by the driver and outputs the operations to the forward recognition camera. ·
Cancels steering assist when an abnormal torque request signal is received from the forward recognition camera. |
|
| Main Body ECU (Multiplex Network Body ECU) | Sends country specification information signals to the forward recognition camera. | |
| Central Gateway ECU (Network Gateway ECU) | Gateway function of CAN communication. | |
OPERATION CONDITION
Operating Conditions of LDA System (Lane Departure Alert Function)
| Operation | Condition |
|---|---|
| Operating | The LDA system (lane departure alert function) is activated when all of the following conditions are met:
·
The LDA main switch is on. (When the LDA main switch is pressed to turn on the LDA system, the LDA indicator light illuminates.) ·
The vehicle speed is above approximately 50 km/h (32 mph) or more. ·
Lane markers are detected. ·
LDA system becomes activated when the turning signal is set to the opposite direction against the heading direction. ·
System malfunction is not detected. |
| Suspended | The LDA system (lane departure alert function) is suspended when any one of the following conditions is met:
·
The vehicle speed is less than approximately 50 km/h (32 mph). ·
A turn signal command is detected. ·
No lane markers are detected. ·
Immediately after the LDA is activated. ·
A malfunction is detected in the LDA system. ·
The temperature of the forward recognition camera is abnormal. ·
The vehicle crosses halfway or further over a lane marker. |
| Canceled/Resume | The LDA system (lane departure alert function) is stopped when any one of the following conditions is met:
·
The LDA main switch is off. ·
The LDA system is malfunctioning. ·
The Power switch is turned off. The LDA system (lane departure alert function) resumes when the following conditions are met: ·
The conditions to start operation listed above returns to are satisfied. ·
The LDA system condition returns to normal. ·
The power switch is turned off and on (IG) again to ensure normal operation, after the LDA system has been stopped by a system malfunction. |
Operating Conditions of LDA System (Steering Assist Function)
| Operation | Condition |
|---|---|
| Operating | The LDA system (steering assist function) is activated when all of the following conditions are met:
·
The LDA main switch is on. (When the LDA main switch is pressed to turn on the LDA system, the LDA indicator light illuminates.) ·
The vehicle speed is above approximately 50 km/h (32 mph) or more. ·
Lane markers are detected. ·
No turn signal command is detected. ·
System malfunction is not detected. ·
The steering assist available is selected via operation on the steering pad switch assembly. ·
Deceleration at or above a constant speed is not detected. ·
Steering operations to change the direction of vehicle travel are not performed. ·
Systems related to vehicle safety, such as the VSC and pre-collision system, do not operate. ·
Acceleration via operation of the accelerator pedal is not detected. ·
The hands off steering wheel alert is not displayed. |
| Suspended | The LDA system (steering assist function) is suspended when any one of the following conditions is met:
·
The vehicle speed is not above approximately 50 km/h (32 mph). ·
A turn signal command is detected. ·
No lane markers are detected. ·
Immediately after the lane departure warning is activated. ·
The airbag ECU assembly (yawrate sensor) is malfunctioning. ·
A malfunction is detected in the LDA system. ·
The deceleration sensor or steering sensor is malfunctioning. ·
The vehicle crosses halfway or further over a lane marker. ·
Steering assist generated to change the direction of vehicle travel is detected. ·
Deceleration at or above a constant speed is detected. ·
Systems related to vehicle safety, such as the VSC and pre-crash safety system, operate. ·
Acceleration via operation of the accelerator pedal is detected. ·
The temperature of the forward recognition camera is abnormal. ·
No steering wheel operation detected. |
| Canceled/ Resume | The LDA system (steering assist function) is stopped when any one of the following conditions is met:
·
The LDA main switch is off. ·
The LDA system is malfunctioning. ·
The power switch is turned off. ·
The Steering assist unavailable is selected via operation of the steering pad switch assembly. The LDA system (steering assist function) resumes when the following conditions are met: ·
The conditions to start operation listed above returns to are satisfied. ·
The LDA system condition returns to normal. ·
The power switch is turned off and on (IG) again to ensure normal operation, after the LDA system has been stopped by a system malfunction. ·
The steering assist available is selected via operation on the steering pad switch assembly. |
Operating Conditions of LDA System (Vehicle Sway Warning Function)
| Operation | Condition |
|---|---|
| Operating | The LDA system (vehicle sway warning function) is activated when all of the following conditions are met:
·
The vehicle speed is above approximately 50 km/h (32 mph) or more. ·
Lane markers are detected. ·
System malfunction is not detected. ·
The vehicle sway warning ON is selected via operation of the steering pad switch assembly. |
| Suspended | The LDA system (vehicle sway warning function) is suspended when any one of the following conditions is met:
·
The vehicle speed is not above approximately 50 km/h (32 mph). ·
A turn signal command is detected. ·
No lane markers are detected. ·
Immediately after the lane departure warning is activated. |
| Canceled/Resume | The LDA system (vehicle sway warning function) is stopped when any one of the following conditions is met:
·
The LDA system is malfunctioning. ·
The power switch is turned off. ·
The vehicle sway warning OFF is selected via operation of the steering pad switch assembly. The LDA system (vehicle sway warning function) resumes when the following conditions are met: ·
The conditions to start operation listed above are satisfied. ·
The LDA system condition returns to normal. ·
The power switch is turned off and on (IG) again to ensure normal operation, after the LDA system has been stopped by a system malfunction. ·
The vehicle sway warning ON is selected via operation of the steering pad switch assembly. |
SYSTEM CONTROL
Function Overview
Lane Departure Alert Function
If the system judges that the vehicle may deviate from the lane it is in, the system illuminates the indicator in the combination meter display and sounds a buzzer so that the driver can take action to avoid lane departure.
Steering Assist Function
If the system judges that the vehicle may deviate from the lane it is in, the system performs steering assist to help the driver correct the path of the vehicle. If the driver does not take appropriate action, the system sounds a buzzer.
Vehicle Sway Warning Function
The system detects drift of the vehicle within its lane, which is often the result of a driver who is tired, distracted or not looking ahead, based on the position of the vehicle within its lane and the steering inputs of the driver and alert the driver before a lane departure or collision occurs.
FUNCTION
Using the Meter Control Switches of the steering pad switch assembly, the steering assist functions and the vehicle sway warning functions can be customized.
| *a | Meter Control Switch | *b | Lane departure Alert Main Switch (LDA Main Switch) |
| *c | The illustration shown is an example. | - | - |
Customize LDA system settings Functions
| Item (Select using the up/down button of the meter control switch) | Description | Setting (Change using the center button of the meter control switch) |
|---|---|---|
| Steering Assist | Select to turn steering wheel assistance on/off | ·
On ·
Off |
| Warning Sensitivity | Timing of lane departure alert function | ·
High ·
Standard |
Customize Vehicle Sway Warning Functions
| Item (Select using the up/down button of the meter control switch) | Description | Setting (Change using the center button of the meter control switch) |
|---|---|---|
| Sway Warning | Select to turn the sway warning function on/off | ·
On ·
Off |
| Sway Sensitivity | Timing of sway warning | ·
High ·
Standard ·
Low |
The vehicle sway warning function provides a warning to alert the driver when any of the following conditions occur:
CONSTRUCTION
Forward Recognition Camera
The forward recognition camera captures a view of the road up to approximately 50 m (164 ft.) ahead of the forward recognition camera.
The forward recognition camera detects lane markers and calculates the radius to the center of the lane, the vehicle center position disparity among the distances from each left and right lane marker and the angle disparity between the vehicle traveling direction and each left and right lane marker.
When one of the following operations is conducted, the forward recognition camera angle must be adjusted. For details, refer to the Repair Manual.
The forward recognition camera is removed and reinstalled or replaced.
Parts relating to the tires or suspension are replaced or adjusted.
Strong force is applied onto the forward recognition camera.
The LDA system does not operate if the vehicle approaches the lane marker (but does not cross it), as long as the vehicle remains parallel with the lane marker.
| *1 | Forward Recognition Camera | - | - |
| *a | Monocular Camera | *b | Approximately 3.0 m (9.8 ft.) or more |
| *c | Lane Marker | *d | Camera Sensor Recognition Range. |
| *e | Approximately 50 m (164 ft.) | - | - |
The LDA system does not operate if the vehicle approaches the lane marker (but does not cross it), as long as the vehicle remains parallel with the lane marker.
| *a | Image captured by forward recognition camera | *b | Left lane marker |
| *c | Center of lane | *d | Right lane marker |
| *e | Angle between the vehicle traveling direction and right lane marker | *f | Distance from the vehicle to right lane marker |
| *g | Distance from the vehicle to left lane marker | *h | Angle between the vehicle traveling direction and left lane marker |
| *i | Lane radius (If only the left lane marker or right lane marker is recognized, the radius of the recognized lane marker will be calculated) | - | - |
OPERATION
Combination Meter Sub-assembly
The combination meter sub-assembly illuminates the indicator lights or displays an indicator on the multi-information display and sounds a buzzer (which is built into the combination meter sub-assembly) in accordance with the respective condition.
| *a | Multi-information Display | *b | LDA Indicator Light |
| *c | Steering Indicator Light | *d | Master Warning Light |
| *a | Multi-information Display | *b | Master Warning Light |
| *c | Steering Indicator Light | *d | LDA Indicator Light |
| Condition | Multi-information Display* |
|
|
Buzzer |
|---|---|---|---|---|
|
*: These illustrations are examples. |
||||
| Steering assist off | Lane Departure
Alert Tuned On Steering Assist Inactive |
Illuminates (Green) | - | - |
| Steering assist on | Lane Departure
Alert Tuned On Steering Assist Active |
Illuminates (Green) | - | - |
| LDA Main Switch OFF |
|
Dose Not Illuminates | - | - |
·
LDA main switch On ·
Steering Assist Unavailable ·
No Markers Detected |
|
Illuminates (Green) | - | - |
·
LDA main switch On ·
Steering Assist Unavailable ·
Lane Markers Detected ·
Under Monitoring |
|
Illuminates (Green) | - | - |
·
LDA main switch On ·
Steering Assist Unavailable ·
One Lane Markers (Right) Detected ·
Under Monitoring |
|
Illuminates (Green) | - | - |
·
LDA main switch On ·
Steering Assist Unavailable ·
Lane Markers Detected ·
LDA Warning Operating |
2.292,1.917 2.208,1.917
2.208,1.917 2.208,1.156
true
2.365,1.844 3.385,2.344
1.021,0.5
10
false
The lane marker icons blinks
|
Blinks (Yellow) | - | Sounds |
·
LDA main switch On ·
Steering Assist Available ·
Lane Markers Detected ·
LDA System with Steering Assist Operating |
|
Illuminates (Green) | Illuminates | - |
·
LDA main switch On ·
Steering Assist Available ·
One Lane Markers (Right) Detected ·
LDA System with Steering Assist Operating |
|
Illuminates (Green) | Illuminates | - |
·
LDA main switch On ·
Steering Assist Available ·
Lane Markers Detected ·
LDA System with Steering Assist Operating ·
LDA Warning Operating |
2.313,2.083 2.24,2.083
2.24,2.083 2.24,1.24
true
2.344,2.01 3.375,2.5
1.031,0.49
10
false
The lane marker icons blinks
|
Blinks (Yellow) | Illuminates | Sounds |
| Condition | Multi-information Display |
|
Buzzer |
|---|---|---|---|
|
*: When display changes |
|||
| System malfunction | LANE DEPARTURE ALERT
MALFUNCTION VISIT YOUR DEALER |
Illuminates | Sounds |
| When temporarily unavailable due to sensors other than the forward recognition camera. | Lane Departure Alert
Unavailable |
Illuminates | Sounds |
| Vehicle Speed is Approximately 50 km/h (32 mph) or Less | LANE DEPARTURE ALERT
UNAVAILABLE BELOW APPROX 50 KM/H |
- | - |
| With LDA main switch is on (steering assist available), no hands are detected on steering wheel | LDA
Hold Steering Wheel* |
- | - |
| LDA Steering
Assist Unavailable Hold Steering Wheel* |
Illuminates | ||
DIAGNOSIS
If a malfunction is detected in the LDA system, the forward recognition camera cancels the LDA system, illuminates the LDA indicator Light in yellow, illuminates the master warning light, sounds the buzzer in the combination meter sub-assembly and displays a message on the multi-information display to inform the driver of the malfunction.
The DTCs can be read when a Global TechStream (GTS) is connected to the DLC3. For details, refer to the Repair Manual.