Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2017.12
NM2070E _58 Vehicle Interior _061890 PRE-CRASH SAFETY _0301434 PRE-CRASH SAFETY SYSTEM DE DETAILS F

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  DETAILS  INDICATOR LIGHT/WARNING LIGHT/MULTI DISPLAY  


OPERATION


a.

Warning Indication

i.

The combination meter assembly uses the multi-information display, master warning light, PCS warning light and buzzer to provide the driver with pre-crash safety system malfunction and indications.


ii.

If the driving support ECU assembly determines that the possibility of a collision is high, it sends a signal to the combination meter assembly and skid control buzzer. Upon receiving this signal, the combination meter assembly indicates a warning using the multi-information display and buzzer sounds. Details are indicated below.

When there is a high possibility of a collision
Multi-information Display Skid Control Buzzer Assembly
BRAKE ! Sounds Continuously


iii.

If the pre-crash safety system is disabled, a message will be displayed on the multi-information display.

When the pre-crash safety system is disabled
Multi-information Display Master Warning Light PCS Warning Light
PRE-CRASH SAFETY OFF - Illuminates


iv.

When the system is not available, the following warning occurs to warn the driver.

When a system malfunction is detected
Multi-information Display Detail Master Warning Light PCS Warning Light Buzzer DTC
PRE-CRASH SAFETY MALFUNCTION
VISIT YOUR DEALER
This message appears when the driving support ECU assembly detects a system malfunction. Illuminates Illuminates Sounds once Repair is required DTCs are stored
PRE-CRASH SAFETY UNAVAILABLE
·

Millimeter wave radar sensor assembly is misaligned

·

Temperature of millimeter wave radar sensor assembly is abnormality

·

Power supply of millimeter wave radar sensor assembly is abnormality


- Illuminates - -
PRE-CRASH SAFETY UNAVAILABLE
CLEAN SENSOR
Dirty front grille emblem or millimeter wave radar sensor assembly. - Illuminates - -
FRONT CAMERA VISION BLOCKED CLEAN AND DEMIST WINDSHIELD Dirty or fog windshield glass over the forward recognition camera. - Illuminates - -
FRONT CAMERA UNAVAILABLE
·

Temperature of forward recognition camera is abnormal.

·

Power supply of forward recognition camera is abnormal.


- Illuminates - -



b.

Changing settings of the pre-crash safety system

i.

Enabling/disabling the pre-crash safety system

1.

The pre-crash safety system can be enabled/disabled on setting display screen of the multi-information display.

HINT:

The system is automatically enabled each time the power switch is turned to ON mode.


2.

If the system is disabled, the PCS warning light will turn on and a message will be displayed on the multi-information display.

Y230127C01
5.938,0.156 6.25,0.313 0.313,0.156 10 false *a 4.708,1.354 5.021,1.51 0.313,0.156 10 false *b 0.177,1.125 0.49,1.281 0.313,0.156 10 false *c
*a PCS warning Light *b Multi-information Display
*c Steering Pad Switch Assembly - -




ii.

Changing the pre-crash warning timing

1.

The pre-crash warning timing can be changed on setting display screen of the multi-information display.

Y230108C01
5.083,0.917 5.396,1.073 0.313,0.156 10 false *a 5.083,1.51 5.396,1.667 0.313,0.156 10 false *b 5.083,2.135 5.396,2.292 0.313,0.156 10 false *c 5.094,0.563 5.406,0.719 0.313,0.156 10 false *d 0.406,1.125 0.719,1.281 0.313,0.156 10 false *e
*a Far *b Middle
*c Near *d Multi-information Display
*e Steering Pad Switch Assembly - -


HINT:
·

The pre-crash safety system is set to Middle by default.

·

When Near is selected, the warning will begin to operate later than with the default timing.

·

When Far is selected, the warning will begin to operate earlier than with the default timing.

·

The Operation timing setting is retained when the power switch is turned off.