Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.08
NM2070E _58 Vehicle Interior _061888 METER / GAUGE / DISPLAY _0301432 METER / GAUGE SYSTEM DE DETAILS F

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  DETAILS  DETAILS  


OPERATING CONDITION


a.

Hybrid System Indicator

i.

The Hybrid System Indicator will begin to operate when both of the following conditions are met:

·

The hybrid system is operating (the READY indicator light is illuminated).

·

Drive (D) or Brake (B) has been selected.



ii.

Eco Driving Indicator Light can operate when all of the following conditions are met :

·

The hybrid system is operating (the READY indicator light is illuminated).

·

Drive (D) has been selected.

·

The Hybrid System Indicator is in the Charge area or Eco area.

·

EV mode is not selected.

·

The hybrid system is normal.

·

The hybrid system temperature is normal.

·

The vehicle is being driven at a speed of 130 km/h (81 mph) or below.





FUNCTION


a.

Combination Meter Sub-assembly

i.

Buzzer Function

1.

The table below shows the warning and reminder functions of the buzzer in the combination meter sub-assembly.

Priority Item

*: Models with Toyota Safety Sense

1 READY
2 Reverse Warning (Once)
3 Rear Seat Belt Warning
4 Seat Belt Warning (Level 2)
5 Rear Seat Belt Warning (Level 1)
6 Seat Belt Warning (Level 1)
7 Unexpected Vehicle Motion Warning (Level 1)
8 Unexpected Vehicle Motion Warning (Level 2)
9 Brake Force Reduction Warning
10 Brake Fluid Low Warning
11 Engine Oil Pressure Warning
12 Hybrid Battery Diagnosis Request (Second Time)
13 EPS Warning
14 Lane Departure Alert System Warning*
15 Smart Key System Warning (Continuous)
16 Smart Key System Warning (Intermittent)
17 Brake System Temperature Rise Warning
18 Smart Key System Warning (Intermittent 2, Maximum 9 times)
19 Smart Key System Warning (Once)
20 Multi-information Display Warning
21 Accelerator Depression with N Position
22 Accelerator Depression Hold Warning
23 Radar Cruise Control Cancelation Due to Low Speed Warning*
24 Immobiliser Certification Reminder
25 Lo Fuel Warning
26 P Position Select Advice
27 HV Battery Low Warning (Continuous)
28 HV Battery Low Warning (Intermittent)
29 Parking Brake Engaged Warning
30 Door Open while Driving Warning
31 Vehicle Sway Warning
32 Shift Reject Warning
33 EV Drive Mode Reject Warning
34 Light Reminder
35 Turn Signal/Hazard Warning Operation




b.

Multi-information Display

i.

Display Function Flow

1.

The multi-information display can be switched as shown in the flow chart below:

Y230123E02
4.927,0.375 6.635,0.677 1.708,0.302 10 false Door Unlock Mode Display 3.031,0.802 3.344,1.063 0.313,0.26 10 false OFF 0.823,0.5 2.042,0.885 1.219,0.385 10 false Warning Display*c 5.552,5.458 6.771,5.844 1.219,0.385 10 false Warning Display*c 2.406,2.094 4.844,2.49 2.438,0.396 10 false Power Switch off to on (ACC) or on (IG) 3.323,2.917 4.396,3.115 1.073,0.198 10 false Opening 3.031,3.958 4.208,4.323 1.177,0.365 10 false Status Display*d 2.667,4.292 4.125,4.5 1.458,0.208 10 false - Drive Information Tab 2.667,4.698 4.563,4.927 1.896,0.229 10 false - Navigation Information Tab* 2.667,5.167 4.354,5.365 1.688,0.198 10 false - Audio Information Tab* 2.667,5.583 4.354,5.781 1.688,0.198 10 false - Clock Tab 2.667,6 4.115,6.427 1.448,0.427 10 false - Driving Assist System Information Tab 2.677,6.802 4.667,7 1.99,0.198 10 false - Message Tab 2.677,7.219 4.667,7.417 1.99,0.198 10 false - Settings Tab 0.333,4.385 1.479,4.823 1.146,0.438 10 false Diagnostic Trouble Code 0.396,6.51 1.427,6.771 1.031,0.26 10 false Interrupt Display 2.76,8.625 4.458,8.927 1.698,0.302 10 false Power Switch on (IG) to off 0.5,8.615 1.729,8.927 1.229,0.313 10 false Warning Display*c 3.458,9.333 3.917,9.531 0.458,0.198 10 false OFF 2.125,8.552 2.438,8.75 0.313,0.198 10 false *a 1.729,7.125 2.042,7.323 0.313,0.198 10 false *a 1.74,4.979 2.052,5.177 0.313,0.198 10 false *a 5.094,6.083 5.406,6.281 0.313,0.198 10 false *a 2.479,1.281 2.792,1.479 0.313,0.198 10 false *a 4.25,1.281 4.563,1.479 0.313,0.198 10 false *a 3.406,0.406 3.719,0.604 0.313,0.198 10 false *a 2.448,0.979 2.76,1.177 0.313,0.198 10 false *b 4.167,0.979 4.479,1.177 0.313,0.198 10 false *b 1.677,4.5 1.99,4.698 0.313,0.198 10 false *b 5.198,5.583 5.51,5.781 0.313,0.198 10 false *b 1.688,6.635 2,6.833 0.313,0.198 10 false *b 1.5,9.531 1.813,9.729 0.313,0.198 10 false *b 3.667,9.01 3.979,9.208 0.313,0.198 10 false *e 3.667,3.292 3.979,3.49 0.313,0.198 10 false *f

*: Models with navigation system


No. Display Change Condition
*a Conditions are met.
*b Conditions are not met.
*c If there are multiple display requests, items will be displayed in sequence.
*d Item or display is selected by operating the steering pad switch.
*e ODO display is displayed for a certain period of time after the power switch is turned off.
*f After power switch is turned on (IG)



ii.

Information Display Tab Operation

·

The information currently displayed can be switched using the RIGHT or LEFT switch of the steering pad switch assembly.

Y229664C03
3.792,1.417 4.333,1.417 true 5.521,1.417 5.948,1.417 true 3.719,0.354 4.031,0.51 0.313,0.156 10 false *1 3.615,1.333 3.865,1.542 0.25,0.208 10 false *a 5.99,1.333 6.229,1.552 0.24,0.219 10 false *b 0.333,2.677 0.646,2.833 0.313,0.156 10 false *c 2.75,2.667 3.219,2.854 0.469,0.188 10 false *d (*A) 5.083,2.677 5.542,2.854 0.458,0.177 10 false *e (*A) 5.083,4.083 5.396,4.24 0.313,0.156 10 false *f 5.083,5.417 5.396,5.625 0.313,0.208 10 false *g 2.75,5.427 3.063,5.583 0.313,0.156 10 false *h 0.354,5.417 0.667,5.573 0.313,0.156 10 false *i 0.083,6.458 0.385,6.667 0.302,0.208 10 false *j
*A Models with Navigation System - -
*1 Steering Pad Switch Assembly - -
*a LEFT Switch *b RIGHT Switch
*c Drive Information *d Navigation Information
*e Audio Information *f Clock
*g Driving Assist System Information *h Message
*i Settings *j The illustrations shown are examples only.
V100136

RIGHT switch operation
V100135

LEFT switch operation




iii.

Drive Information Mode Function

·

The drive information tab shows vehicle information such as drivable range and fuel consumption.

·

The drive information display can be changed by using the UP/DOWN switch of the steering pad switch assembly.

Y229665C02
4.927,0.844 4.927,0.51 4.927,0.51 5.708,0.51 true 4.927,1.99 4.927,2.344 4.927,2.344 5.708,2.344 true 3.729,0.333 4.042,0.49 0.313,0.156 10 false *1 5.75,0.427 6.063,0.583 0.313,0.156 10 false *a 5.75,2.26 6.063,2.417 0.313,0.156 10 false *b 0.354,2.677 0.667,2.833 0.313,0.156 10 false *c 2.75,2.677 3.063,2.833 0.313,0.156 10 false *d 5.083,2.677 5.396,2.833 0.313,0.156 10 false *e 5.083,4.51 5.396,4.667 0.313,0.156 10 false *f 5.083,6.333 5.354,6.531 0.271,0.198 10 false *g 2.729,6.344 3.385,6.521 0.656,0.177 10 false *h (*A) 0.354,6.344 0.667,6.5 0.313,0.156 10 false *i 0.125,7.521 0.438,7.74 0.313,0.219 10 false *j
*1 Steering Pad Switch Assembly - -
*a UP Switch *b DOWN Switch
*c Energy Monitor *d Hybrid System Indicator
*e Eco Score *f Fuel Consumption Record
*g Drive Range *h Vehicle Sway Warning
*i Blank *j The illustrations shown are examples only.
*A Models with Toyota Safety Sense - -
V100136

DOWN switch operation
V100135

UP switch operation




iv.

Setting Function

·

The items displayed on the multi-information display can be customized.

·

The following items can be selected on the information setting screen.

Lane Departure Alert System (Models with Toyota Safety Sense)
Item Available Setting
Steering Assist

Setting for steering assist can be set to on/off:

-

On

-

Off



Warning Sensitivity

Alert sensitivity of alert system can be changed:

-

High

-

Standard




Pre-crash Safety system (Models with Toyota Safety Sense)
Item Available Setting
PCS

The pre-crash system can be set to on/off:

-

On

-

Off



Pre-crash warning timing

The pre-crash warning timing can be selected:

-

Far (Icon is displayed)

-

Middle (Icon is displayed)

-

Near (Icon is displayed)




Vehicle Sway Warning (Models with Toyota Safety Sense)
Item Available Setting
Vehicle Sway Warning

Vehicle sway warning function can be set to on/off:

-

On

-

Off



Vehicle Sway Warning Sensitivity

Vehicle sway warning sensitivity can be selected:

-

High

-

Standard

-

Low




Meter Customize
Item Available Setting

*1: Available display languages differ by destination

*2: Available display units differ by destination

*3: Models with Navigation System

Language*1

The language used on the multi-information display can be selected:

-

English

-

French

-

Spanish

-

German

-

Italian

-

Traditional Chinese

-

Japanese



Unit*2

The unit displayed on the multi-information display can be selected:

-

km (km/L)

-

km (L/100km)



Interruption Display

The following interruption display can be turned on or off:

-

Turn-by-turn Navigation Display*3

-

Incoming Telephone Display

-

Heater Control Panel Switch Operation



Initialization The set items can be initialized.



v.

Warning Mode Function

·

When a warning is necessary, the warning display interrupts the current display on the multi-information display.

·

The master warning light may illuminate or blink and the buzzer in the combination meter sub-assembly may sound depending on the item displayed on the multi-information display.


Priority Display Master Warning Light Buzzer

*1: Models with Toyota Safety Sense

*2: Skid control buzzer operation is activated

*3: Models with LED headlight

*4: Models with Acoustic Vehicle Alerting System

1 MAINTENANCE MODE - -
CERTIFICATION MODE - -
ADJUSTING FORWARD CAMERA*1 - -
ERROR ADJUSTING FRONT RADAR BEAM*1 - -
ADJUSTING FRONT RADAR BEAM VERTICAL*1 - -
ADJUSTING FRONT RADAR BEAM HORIZONTAL*1 - -
ADJUSTING FRONT RADAR BEAM*1 - -
CHECKING PCS BRAKE*1 - -
CHECKING CRUISE CONTROL BRAKE*1 - -
BRAKE!*1 - -*2
2 Dynamic radar cruise control warning reminder indicator (image display)*1 - -
Lane departure alert warning reminder indicator (image display)*1 - -
SHIFT TO P
BEFORE EXITING VEHICLE
Blinks Sounds
3 POWER TURNED OFF TO SAVE BATTERY - -
4 SHIFT TO P
BEFORE EXITING VEHICLE
Blinks Sounds
5 SHIFT IS IN N
RELEASE ACCELERATOR BEFORE SHIFTING
Blinks Sounds
DEPRESS BRAKE WHEN VEHICLE IS STOPPED
HYBRID SYSTEM MAY OVERHEAT
Blinks Sounds
HYBRID BATTERY LOW HYBRID SYSTEM STOPPED
SHIFT TO P AND RESTART
Blinks Sounds
6 P LOCK MALFUNCTION WHEN PARKING, PARK IN FLAT PLACE AND APPLY PARKING BRAKE SECURELY Illuminates Sounds
7 HYBRID SYSTEM MALFUNCTION
STOP IN A SAFE PLACE SEE OWNER'S MANUAL
Illuminates Sounds
SHIFT OUT OF N TO RECHARGE Blinks Sounds
KEY NOT DETECTED Blinks Sounds
RELEASE ACCELERATOR Blinks Sounds
8 LDA HOLD STEERING WHEEL*1 - -
LDA STEERING ASSIST UNAVAILABLE HOLD STEERING WHEEL*1 Illuminates -
9 CLEAN RADAR SENSOR*1 Illuminates Sounds
CRUISE CONTROL NOT AVAILABLE*1 Illuminates Sounds
ENTRY & START SYSTEM CHECK
HAVE YOUR VEHICLE CHECKED BY A DEALER
Blinks Sounds
CHECK CRUISE CONTROL SYSTEM*1 Illuminates Sounds
LANE DEPARTURE ALERT MALFUNCTION
VISIT YOUR DEALER*1
Illuminates Sounds
FRONT CAMERA UNAVAILABLE*1 - -
LANE DEPARTURE ALERT UNAVAILABLE*1 Illuminates Sounds
LANE DEPARTURE ALERT TURNED ON
STEERING ASSIST ACTIVE*1
- -
LANE DEPARTURE ALERT TURNED ON
STEERING ASSIST INACTIVE*1
- -
FRONT CAMERA UNAVAILABLEREMOVE DEBRISON WINDSHIELD*1 - -
PRE-CRASH SAFETY MALFUNCTION
VISIT YOUR DEALER*1
Illuminates Sounds
LOW ENGINE OIL PRESSURE Illuminates Sounds
LANE DEPARTURE ALERT UNAVAILABLE BELOW APPROX 50KM/H *1 - -
LANE DEPARTURE ALERT UNAVAILABLE BELOW APPROX 32MPH *1 - -
LANE DEPARTURE ALERT UNAVAILABLE AT CURRENT SPEED*1 - -
10 Dynamic radar cruise control indicator (image display)*1 - -
Lane departure alert indicator (image display)*1 - -
TURN POWER OFF Blinks Sounds
WOULD YOU LIKE TO TAKE A REST?*1 - Sounds
PLEASE TAKE A REST*1 - Sounds
KEY DETECTED IN VEHICLE Blinks Sounds
DEPRESS BRAKE PEDAL, TOUCH POWER SWITCH WITH KEY Blinks Sounds
DEPRESS BRAKE PEDAL AND PUSH POWER SWITCH TO START Blinks Sounds
SHIFT TO P POSITION TO START Blinks Sounds
11 STEERING WHEEL LOCK
PRESS ENGINE SWITCH WHILE TURNING WHEEL
Blinks Sounds
SHIFT TO P POSITION TO START Blinks Sounds
DRIVE-START CONTROL MALFUNCTION VISIT YOUR DEALER Illuminates Sounds
BRAKE OVERRIDE MALFUNCTION VISIT YOUR DEALER. Illuminates Sounds
12 KEY BATTERY LOW Illuminates Sounds
HYBRID SYSTEM OVERHEAT Illuminates Sounds
HEADLIGHT SYSTEM MALFUNCTION
VISIT YOUR DEALER*3
Illuminates Sounds
ACOUSTIC VEHICLE ALERTING SYSTEM MALFUNCTIONVISIT YOUR DEALER*4 Illuminates Sounds
ACCELERATOR AND BRAKE PEDALSPRESSED SIMULTANEOUSLY Blinks -
13 AUX BATTERY LOW
SEE OWNER'S MANUAL
- -
TO ACTIVATE AUTO HIGH BEAM, SWITCH HEADLIGHTS TO HIGH BEAM*1 - -
POWER ON - -
VSC TURNED OFF PRE-CRASH BRAKE SYSTEM UNAVAILABLE*1 - -
PRE-CRASH SAFETY UNAVAILABLE*1 - -
PRE-CRASH SAFETY UNAVAILABLE CLEAN SENSOR*1 - -
PRE-CRASH SAFETY OFF*1 - -
EV MODE NOT AVAILABLE - Sounds
EV MODE NOT AVAILABLE WARMING UP - Sounds
EV MODE NOT AVAILABLE LOW BATTERY - Sounds
EV MODE NOT AVAILABLE EXCESSIVE SPEED - Sounds
EV MODE NOT AVAILABLE EXCESSIVE ACCELERATION - Sounds
EV MODE DEACTIVATED - Sounds
EV MODE DEACTIVATED LOW BATTERY - Sounds
EV MODE DEACTIVATED EXCESSIVE SPEED - Sounds
EV MODE DEACTIVATED EXCESSIVE ACCELERATION - Sounds
13 HAVE HYBRID BATTERY INSPECTED - -
VEHICLE WILL SOON NOT BE ABLE TO BE STARTED HAVE HYBRID BATTERY INSPECTED - Sounds
VEHICLE SHOULD NOT BE STARTED UNDER ANY CIRCUMSTANCES UNTIL HYBRID BATTERY IS INSPECTED - -
DIAGNOSING HYBRID BATTERY - -
INSUFFICIENTRY CHARGED AUXILIARY BATTERY. THE GEARS CANNOT BE CHANGED. SEE OWNER'S MANUAL Blinks Sounds
SHIFTING TEMPORARILY UNAVAILABLE. WAIT A MOMENT AND TRY AGAIN Blinks Sounds
CAN NOT SHIFT TO B.
SHIFT TO D ONCE TO SHIFT TO B
Blinks Sounds
CAN NOT SHIFT TO D OR R.
SHIFT AFTER HYBRID SYSTEM STARTS
Blinks Sounds
SHIFTING UNAVAILABLE. PRESS BRAKE PEDAL BEFORE SHIFTING Blinks Sounds
SWITCHED TO N.
SHIFT TO D ONCE TO SHIFT TO B
Blinks Sounds
SWITCHED TO N.
TO SHIFT TO D, STOP CAR FIRST
Blinks Sounds
SWITCHED TO N.
TO SHIFT TO R, STOP CAR FIRST
Blinks Sounds
SWITCHED TO N.
TO SHIFT TO P, STOP CAR AND PRESS P SWITCH
Blinks Sounds
INSUFFICIENT AUX BATTERY CHARGE WHEN PARKING, APPLY PARKING BRAKE SECURELY THEN SEE OWNER'S MANUAL Illuminates Sounds
SHIFT SYSTEM MALFUNCTION WHEN PARKING, APPLY PARKING BRAKE SECURELY THEN SEE OWNER'S MANUAL Illuminates Sounds
SHIFT SYSTEM MALFUNCTION SEE OWNER'S MANUAL Illuminates Sounds
SHIFT SYSTEM COMMUNICATION MALFUNCTION.
WHEN PARKING, APPLY PARKING BRAKE SECURELY THEN SEE OWNER'S MANUAL
Illuminates Sounds
14 CHECK HEADLIGHT SYSTEM*3 Illuminates/Blinks -
MAINTENANCE REQUIRED FOR HYBRID BATTERY COOLING PARTS AT YOUR DEALER - -



c.

Rear Seat Belt Warning

i.

The combination meter sub-assembly displays the rear seat belt warning based on the rear seat belt buckle switches and courtesy switches for the rear doors. If a warning is necessary, the buzzer in the combination meter sub-assembly will also sound.


ii.

The flow of operations that results in a rear seat belt warning is as follows:

Y120644E02
0.594,0.469 1.104,0.677 0.51,0.208 10 false (a), (b) 2.417,0.469 2.677,0.677 0.26,0.208 10 false (c) 5.698,0.479 6.208,0.688 0.51,0.208 10 false (d), (e)

Step Condition Transition Multi-information Display Buzzer
(a) Power switch is off. Warning is not displayed. No Sound
(b) A rear door is opened then closed.
(c)
·

Power switch is turned on (IG).

·

A seat belt is fastened.


·

In this case, all seats will be displayed as being unfastened regardless of the number of occupants. If seat belts are then fastened, the display for the relevant seat will go off.

·

The warning will be displayed for approximately 66 seconds and then go off.


(d) Any of the rear seat belts are unfastened.
·

Seats with an unfastened seat belt will be displayed regardless of the number of occupants.


If the vehicle speed exceeds 20 km/h (12 mph):
1.

Sounds for 6 seconds*1

2.

Sounds for an additional 60 seconds*2


(e)

When one of the following conditions is met, the buzzer will stop sounding.

-

The seat belt is refastened.


-

The vehicle speed decreases to less than approximately 2 km/h (1.2 mph) and either the parking brake is applied or the P position switch is pressed.



·

Seats with an unfastened seat belt will be displayed regardless of the number of occupants.

·

The warning message will be displayed for approximately 66 seconds and then go off.


Stops sounding

*1: Sound cycle is 1.2 seconds.

*2: Sound cycle is 0.4 seconds.



d.

Headup Display Customize

i.

The items displayed on the headup display can be customized.


ii.

Pressing and holding the SET switch changes the headup display to setting mode, enabling each display to be enabled or disabled.

Y174933C01
0.25,0.333 0.5,0.542 0.25,0.208 10 false *a 2.25,0.573 2.49,0.823 0.24,0.25 10 false *d 3.219,0.646 3.688,0.854 0.469,0.208 10 false *c 0.375,1.917 0.625,2.125 0.25,0.208 10 false *b

Text in Illustration
*a Vehicle Speed Display *b Advisory Display of Switching to On/off Setting Mode
*c Turn-by-turn Navigation ON/OFF Setting *d Returns to the normal headup display when vehicle speed reaches 8 km/h (5 mph) or when 10 seconds have elapsed without any operation.
V100135

SET switch is pressed and held.
V100136

SET switch is pressed briefly.
V100138

Position adjustment switch is operated. - -




CONSTRUCTION


a.

Headup Display

i.

The headup display projects the image from the dot Vacuum Fluorescent Display (VFD), built into the headup display unit (combination meter mirror ECU), in a position approximately 2 m (6.6 ft) forward of the driver using a concave mirror and the windshield in order to support the driver with various information.


ii.

By changing the angle of the concave mirror, the position of the image displayed can be adjusted.

Y103068E03
0.813,1.354 0.677,1.104 0.677,1.104 0.51,1.104 true 2.969,1.729 2.833,1.979 2.833,1.979 2.667,1.979 true 3.573,1.729 3.708,1.979 3.708,1.979 4.083,1.979 true 3.729,1.594 3.906,1.698 3.906,1.698 4.083,1.698 true 4.917,0.563 4.771,0.313 4.771,0.313 4.604,0.313 true 0.333,1 0.542,1.208 0.208,0.208 10 false *1 2.49,1.875 2.698,2.083 0.208,0.208 10 false *3 4.104,1.865 4.313,2.073 0.208,0.208 10 false *4 4.104,1.573 4.313,1.781 0.208,0.208 10 false *5 4.417,0.208 4.625,0.417 0.208,0.208 10 false *2

Text in Illustration
*1 Headup Display Image *2 Windshield Glass
*3 Concave Mirror *4 Dot VFD
*5 Headup Display Unit (Combination Meter Mirror ECU) - -



b.

Windshield Glass for Headup Display

i.

Windshield glass without a combiner treatment is used for the headup display.


ii.

This glass has a wedge-shaped inner film. This film, with its varying thickness, is located between the outer and inner layers of glass.


iii.

The light that strikes the glass is reflected by the inner surface of the inner glass, and also by the inner side of the outer surface of outer layer of glass. With a conventional windshield, the light reflected from these 2 surfaces diverges due to the thickness of the glass, resulting in a double image.


iv.

The film's wedge shape is used to eliminate the reflection angle difference between the outer glass and inner glass. This recombines the reflected light and eliminates the double image.


v.

Thus, the reflected light from the headup display unit is seen by the driver as a single display image.

Y103069E04
1.135,2.26 1,2.51 1,2.51 0.833,2.51 true 4.51,2.26 4.375,2.51 4.375,2.51 4.208,2.51 true 1.292,1.313 0.823,2 0.823,2 0.656,2 true 2.083,0.542 2.052,0.156 2.052,0.156 1.927,0.156 true 5.021,0.74 4.875,0.49 4.875,0.49 4.719,0.49 true 5.135,0.792 5.01,0.177 5.01,0.177 4.844,0.177 true 2.188,0.656 2.677,0.479 2.677,0.479 2.844,0.479 true 2.146,0.604 2.51,0.198 2.51,0.198 2.625,0.198 true 5.229,0.854 5.646,0.75 5.646,0.75 5.74,0.75 true 0.635,2.417 0.844,2.625 0.208,0.208 10 false *5 1.917,2.469 2.177,2.677 0.26,0.208 10 false *A 5.406,2.469 5.667,2.677 0.26,0.208 10 false *B 5.302,1.115 5.563,1.323 0.26,0.208 10 false *b 4.021,2.417 4.229,2.625 0.208,0.208 10 false *5 0.49,1.896 0.698,2.104 0.208,0.208 10 false *4 1.729,0.063 1.938,0.271 0.208,0.208 10 false *1 2.875,0.375 3.083,0.583 0.208,0.208 10 false *3 2.01,1.125 2.219,1.333 0.208,0.208 10 false *a 3.76,1.708 3.969,1.917 0.208,0.208 10 false *8 5.667,0.333 5.875,0.542 0.208,0.208 10 false *7 4.542,0.396 4.75,0.604 0.208,0.208 10 false *1 4.656,0.042 4.865,0.25 0.208,0.208 10 false *6 2.646,0.073 2.854,0.281 0.208,0.208 10 false *2 5.771,0.667 5.979,0.875 0.208,0.208 10 false *3

Text in Illustration
*A Windshield Glass with Normal Film *B Windshield Glass with Wedge-shaped Film
*1 Outer Glass *2 Uniform Thickness Film
*3 Inner Glass *4 Combiner
*5 Concave Mirror *6 Wedge-shaped Film
*7 Thick *8 Thin
*a The combiner makes the light reflected by the inner glass brighter, however, a double image is caused by a divergence of the reflected light. *b Reflected light is recombined and a double image is prevented.