Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2012.03–2016.05
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM U

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


U154222E02
2.448,0.271 2.719,0.427 0.271,0.156 10 false D28 5.438,0.26 5.708,0.417 0.271,0.156 10 false A57

HINT:

The standard normal voltage between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of the terminals, and displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A57-20 (BATT) - D28-104 (E1) R - BR Auxiliary battery (for measuring auxiliary battery voltage and for ECM memory) Always 11 to 16 V
A57-2 (+B) - D28-104 (E1) B - BR Power source of ECM Power switch on (IG) 11 to 14 V
A57-1 (+B2) - D28-104 (E1) B - BR Power source of ECM Power switch on (IG) 11 to 14 V
A57-3 (+BM) - D28-104 (E1) GR - BR Power source of throttle actuator Always 11 to 16 V
D28-108 (IGT1) - D28-104 (E1) P - BR Ignition coil assembly
(ignition signal)
Idling Pulse generation
(see waveform 1)
D28-107 (IGT2) - D28-104 (E1) G - BR
D28-106 (IGT3) - D28-104 (E1) P - BR
D28-105 (IGT4) - D28-104 (E1) Y - BR
D28-23 (IGF1) - D28-104 (E1) L - BR Ignition coil assembly
(ignition confirmation signal)
Power switch on (IG) 4.5 to 5.5 V
Idling Pulse generation
(see waveform 1)
D28-74 (NE+) - D28-120 (NE-) B - W Crankshaft position sensor Idling with warm engine Pulse generation
(see waveform 2)
D28-76 (G2+) - D28-122 (G2-) B - W Camshaft position sensor Idling with warm engine Pulse generation
(see waveform 3)
D28-85 (#10) - D28-109 (E01) Y - BR Fuel injector assembly Power switch on (IG) 11 to 14 V
D28-84 (#20) - D28-109 (E01) B - BR
D28-83 (#30) - D28-109 (E01) L - BR
D28-82 (#40) - D28-109 (E01) R - BR
D28-85 (#10) - D28-109 (E01) Y - BR Fuel injector assembly Idling Pulse generation
(see waveform 4)
D28-84 (#20) - D28-109 (E01) B - BR
D28-83 (#30) - D28-109 (E01) L - BR
D28-82 (#40) - D28-109 (E01) R - BR
D28-18 (HA1A) - D28-46 (E04) G - BR Air fuel ratio sensor (sensor 1) heater Power switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 5)
D28-103 (A1A+) - D28-104 (E1) R - BR Air fuel ratio sensor (sensor 1) Idling 3.3 V*1
D28-126 (A1A-) - D28-104 (E1) G - BR Air fuel ratio sensor (sensor 1) Idling 3.0 V*1
D28-41 (HT1B) - D28-86 (E03) G - BR Heated oxygen sensor (sensor 2) heater Power switch on (IG) 11 to 14 V
Idling Below 3.0 V
D28-125 (OX1B) - D28-102 (O1B-) G - R Heated oxygen sensor (sensor 2) Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(see waveform 6)
D28-87 (KNK1) - D28-110 (EKNK) B - W Knock control sensor Engine speed maintained at 2500 rpm after warming up engine Pulse generation
(see waveform 7)
D28-64 (THW) - D28-65 (ETHW) BR - P Engine coolant temperature sensor Idling, engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
D28-116 (THA) - D28-93 (ETHA) P - BR Intake air temperature sensor (built into mass air flow meter sub-assembly) Idling, intake air temperature 20°C (68°F) 0.5 to 3.4 V
D28-94 (VG) - D28-117 (E2G) B - W Mass air flow meter sub-assembly Idling, neutral (N) selected, A/C switch off 0.5 to 3.0 V
A57-36 (W) - D28-104 (E1) LG - BR MIL Power switch on (IG) (MIL on) Below 3.0 V
Power switch on (READY) 11 to 14 V
D28-90 (VTA1) - D28-111 (ETA) Y - G Throttle position sensor (for engine control) Power switch on (IG), accelerator pedal fully released 0.5 to 1.1 V
D28-89 (VTA2) - D28-111 (ETA) B - G Throttle position sensor (for sensor malfunction detection) Power switch on (IG), accelerator pedal fully released 2.1 to 3.1 V
D28-88 (VCTA) - D28-111 (ETA) R - G Power source of throttle position sensor (specific voltage) Power switch on (IG) 4.5 to 5.5 V
D28-21 (M+) - D28-19 (ME01) L - BR Throttle actuator Idling with warm engine Pulse generation
(see waveform 8)
D28-20 (M-) - D28-19 (ME01) P - BR Throttle actuator Idling with warm engine Pulse generation
(see waveform 9)
D28-28 (PRG) - D28-104 (E1) V - BR Purge VSV Power switch on (IG) 11 to 14 V
Idling, under purge control Pulse generation
(see waveform 10)
A57-8 (FC) - D28-104 (E1) R - BR Fuel pump control Power switch on (IG) 11 to 14 V
Idling Below 1.5 V
A57-26 (TACH) - D28-104 (E1) B - BR Engine speed Idling Pulse generation
(see waveform 11)
A57-7 (TC) - D28-104 (E1) P - BR Terminal TC of DLC3 Power switch on (IG) 11 to 14 V
D28-36 (OC1+) - D28-59 (OC1-) G - Y Camshaft timing oil control valve assembly Idling Pulse generation
(see waveform 12)
A57-13 (CANH) - D28-104 (E1) P - BR CAN communication line Power switch on (IG) Pulse generation
(see waveform 13)
A57-5 (CANL) - D28-104 (E1) V - BR CAN communication line Power switch on (IG) Pulse generation
(see waveform 14)
A57-12 (CANP) - D28-104 (E1) B - BR CAN communication line Power switch on (IG) Pulse generation
(see waveform 13)
A57-4 (CANN) - D28-104 (E1) W - BR CAN communication line Power switch on (IG) Pulse generation
(see waveform 14)
A57-28 (IGSW) - D28-104 (E1) W - BR Power switch Power switch on (IG) 11 to 14 V
A57-6 (MREL) - D28-104 (E1) G - BR EFI MAIN relay Power switch on (IG) 11 to 14 V
D28-99 (VCV1) - D28-104 (E1) R - BR Power source of camshaft position sensor Power switch on (IG) 4.5 to 5.0 V
A57-10 (WPO) - D28-104 (E1) L - BR Engine water pump assembly Idling with warm engine Pulse generation
(see waveform 15)
A57-11 (WPI) - D28-104 (E1) G - BR Engine water pump assembly Idling with warm engine Pulse generation
(see waveform 16)
D28-72 (VCPM) - D28-71 (EPIM) L - Y Power source of manifold absolute pressure sensor Power switch on (IG) 4.75 to 5.25 V
D28-69 (PIM) - D28-71 (EPIM) B - Y Manifold absolute pressure sensor Power switch on (IG) 3.0 to 5.0 V
D28-45 (EGR1) - D28-104 (E1) R - BR EGR valve assembly EGR valve operating Pulse generation
(see waveform 17)
D28-44 (EGR2) - D28-104 (E1) V - BR EGR valve assembly EGR valve operating Pulse generation
(see waveform 17)
D28-43 (EGR3) - D28-104 (E1) Y - BR EGR valve assembly EGR valve operating Pulse generation
(see waveform 17)
D28-42 (EGR4) - D28-104 (E1) LG - BR EGR valve assembly EGR valve operating Pulse generation
(see waveform 17)
D28-48 (G2O) - D28-104 (E1) Y - BR Camshaft revolution signal Idling Pulse generation
(see waveform 18)
A57-22 (FANH) - D28-104 (E1) LG - BR Cooling fan relay Power switch on (IG) 11 to 14 V
A57-21 (FANL) - D28-104 (E1) L - BR Cooling fan relay Power switch on (IG) 11 to 14 V
A57-46 (PWMS) - D28-104 (E1) G - BR Power mode switch Power switch on (IG) 11 to 14 V
Power switch on (IG), power mode switch pressed 0 to 1.5 V
D28-104 (E1) - Body ground BR - Body ground Ground Always Below 1 Ω
D28-109 (E01) - Body ground BR - Body ground Ground Always Below 1 Ω
D28-81 (E02) - Body ground W-B - Body ground Ground Always Below 1 Ω
D28-86 (E03) - Body ground BR - Body ground Ground Always Below 1 Ω
D28-46 (E04) - Body ground BR - Body ground Ground Always Below 1 Ω
A57-32 (EC) - Body ground W-B - Body ground Ground Always Below 1 Ω
D28-22 (GE01) - D28-104 (E1) W-B - BR Shield earth (ground) circuit of throttle actuator Always Below 1 V

HINT:

*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.


WAVEFORM 1


A122717E53
3.021,0.938 3.385,1.135 0.365,0.198 10 false GND 3.031,1.583 3.365,1.781 0.333,0.198 10 false GND 0.208,0.313 0.531,0.771 0.323,0.458 10 false CH1 (IGT) 0.188,1.302 0.573,1.698 0.385,0.396 10 false CH2 (IGF1) 0.031,0.031 0.573,0.208 0.542,0.177 10 false 2 V/DIV. 1.292,1.906 2.042,2.052 0.75,0.146 10 false 20 ms./DIV.

Ignition Coil Assembly Signal (IGT and IGF1 Signal)
ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 2


A254145E19
2.969,0.99 3.323,1.188 0.354,0.198 10 false GND 0.063,0.063 0.604,0.24 0.542,0.177 10 false 5 V/DIV. 1.219,1.917 1.969,2.063 0.75,0.146 10 false 20 ms./DIV.

Crankshaft Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 3


A254147E01
2.986,0.993 3.323,1.140 0.336,0.147 10 GND 1.159,1.916 1.902,2.062 0.744,0.147 10 20 ms./DIV. 2.748,0.059 3.284,0.206 0.536,0.147 10 5 V/DIV.

Camshaft Position Sensor Signal
ECM Terminal Name Between G2+ and G2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 4


A230081E02
0.471,0.517 1.084,0.719 0.613,0.202 10 20 V/DIV. 0.526,2.134 0.879,2.336 0.352,0.202 10 GND 1.793,2.516 2.552,2.718 0.760,0.202 10 20 ms./DIV.

No. 1 (to No. 4) Fuel Injector Assembly Signal
ECM Terminal Name Between #10 (to #40) and E01
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 5


A168188E01
2.354,0.519 2.899,0.678 0.545,0.159 10 5 V/DIV. 2.833,1.647 3.166,1.789 0.333,0.142 10 GND 1.153,2.743 1.897,2.885 0.745,0.142 10 10 ms./DIV.

Air Fuel Ratio Sensor (Sensor 1) Heater Signal
ECM Terminal Name Between HA1A and E04
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling

HINT:

The wavelength varies in accordance with the engine operating condition.



WAVEFORM 6


A230082E02
0.434,0.618 1.114,0.799 0.679,0.181 10 0.2 V/DIV. 0.503,2.147 0.867,2.359 0.364,0.211 10 GND 1.649,2.554 2.513,2.724 0.864,0.170 10 200 ms./DIV.

Heated Oxygen Sensor (Sensor 2) Signal
ECM Terminal Name Between OX1B and O1B-
Tester Range 0.2 V/DIV. 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:

In the Data List, the items O2S B1S2 show the values input to the ECM from the heated oxygen sensor.



WAVEFORM 7


A194185E01
2.968,1.591 3.309,1.757 0.341,0.166 10 GND 2.738,0.591 3.272,0.773 0.534,0.181 10 1 V/DIV. 1.215,2.556 1.916,2.737 0.702,0.181 10 1 ms./DIV.

Knock Control Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 2500 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle condition.




WAVEFORM 8


A208000E70
2.854,1 3.188,1.146 0.333,0.146 10 false GND 2.635,0.219 3.177,0.365 0.542,0.146 10 false 5 V/DIV. 0.5,0.615 0.719,0.76 0.219,0.146 10 false M+ 1.323,1.802 2,1.958 0.677,0.156 10 false 1 ms./DIV.

Throttle Actuator Positive Terminal Signal
ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 9


A245848E64
2.849,0.99 3.182,1.142 0.333,0.151 10 GND 2.627,0.266 3.166,0.409 0.539,0.142 10 5 V/DIV. 0.479,0.626 0.664,0.777 0.184,0.15 10 M- 1.323,1.82 1.996,1.967 0.672,0.147 10 1 ms./DIV.

Throttle Actuator Negative Terminal Signal
ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 10


A149742E10
2.837,1.657 3.173,1.806 0.336,0.149 10 GND 1.104,2.622 1.897,2.763 0.794,0.141 10 20 ms./DIV. 2.537,0.639 3.170,0.795 0.633,0.156 10 10 V/DIV.

Purge VSV Signal
ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 11


A194181E04
2.988,1.797 3.329,1.963 0.341,0.166 10 GND 2.755,0.597 3.289,0.778 0.534,0.181 10 5 V/DIV. 1.186,2.545 1.940,2.726 0.754,0.181 10 10 ms./DIV.

Engine Speed Signal
ECM Terminal Name Between TACH and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 12


A194182E14
0.125,1.844 0.469,2.01 0.344,0.167 10 false GND 2.771,0.521 3.302,0.698 0.531,0.177 10 false 5 V/DIV. 1.469,2.594 2.146,2.771 0.677,0.177 10 false 1 ms./DIV.

Camshaft Timing Oil Control Valve Assembly Signal
ECM Terminal Name Between OC1+ and OC1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 13


A194183E02
2.962,1.99 3.303,2.156 0.341,0.166 10 GND 2.764,0.6 3.298,0.781 0.534,0.181 10 1 V/DIV. 1.117,2.545 1.989,2.726 0.872,0.181 10 10 μsec./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1, CANP and E1
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 14


A194184E02
2.988,1.994 3.329,2.161 0.341,0.166 10 GND 2.75,0.593 3.285,0.774 0.534,0.181 10 1 V/DIV. 1.117,2.545 1.975,2.726 0.858,0.181 10 10 μsec./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1, CANN and E1
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 15


A214025E01
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Engine Water Pump Assembly Signal (from ECM to Engine Water Pump Assembly)
ECM Terminal Name Between WPO and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine water pump speed increases.



WAVEFORM 16


A214025E01
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Engine Water Pump Assembly Signal (from Engine Water Pump Assembly to ECM)
ECM Terminal Name Between WPI and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine water pump speed increases.



WAVEFORM 17


A214026E01
2.849,2.294 3.179,2.450 0.330,0.156 10 GND 2.849,1.922 3.179,2.077 0.330,0.156 10 GND 2.849,1.578 3.179,1.734 0.330,0.156 10 GND 2.849,1.24 3.179,1.396 0.330,0.156 10 GND 0.235,1.039 0.686,1.195 0.451,0.156 10 EGR1 0.235,1.405 0.686,1.560 0.451,0.156 10 EGR2 0.235,1.757 0.686,1.913 0.451,0.156 10 EGR3 0.235,2.113 0.686,2.269 0.451,0.156 10 EGR4 1.248,2.42 1.997,2.577 0.749,0.157 10 50 ms./DIV. 1.979,0.406 2.643,0.581 0.665,0.175 10 20 V/DIV.

EGR Valve Assembly Signal
ECM Terminal Name Between EGR1 and E1, EGR2 and E1, EGR3 and E1, EGR4 and E1
Tester Range 20 V/DIV., 50 ms./DIV.
Condition EGR valve operating


WAVEFORM 18


A214025E01
2.987,1.794 3.317,1.950 0.330,0.156 10 GND 1.269,2.584 2.024,2.772 0.756,0.188 10 20 ms./DIV. 2.394,0.238 2.939,0.405 0.545,0.167 10 5 V/DIV.

Camshaft Revolution Signal from ECM to Power Management Control ECU and Inverter with Converter Assembly
ECM Terminal Name Between G2O and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.