Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2013.08–2014.11
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P0401  Exhaust Gas Recirculation Flow Insufficient Detected  


DESCRIPTION

Based on the driving conditions, the ECM regulates the volume of exhaust gas that is recirculated to the engine's combustion chambers and thus lowers the combustion temperature to reduce NOx emissions. The ECM monitors signals such as engine speed, coolant temperature, electric load, and vehicle speed. When the EGR permission conditions are fulfilled, the ECM controls the opening of the EGR valve linearly through signals to the EGR step motor.

DTC No. DTC Detection Condition Trouble Area
P0401 Change in intake manifold pressure is small when the EGR valve is opened and closed during idle fuel cut operation (2 trip detection logic).
·

EGR valve assembly

·

EGR passage

·

EGR pipe with cooler sub-assembly

·

Manifold absolute pressure sensor

·

Intake system



MONITOR DESCRIPTION

The ECM monitors the pressure inside the intake manifold while opening and closing the EGR valve during fuel cut operation. If there is no change in the manifold absolute pressure sensor value, the ECM interprets this as a malfunction in the EGR valve assembly, illuminates the MIL and stores the DTC (2 trip detection logic).

MONITOR STRATEGY

Required sensors/Components (Main) EGR valve assembly
Manifold absolute pressure sensor
Required sensors/Components (Related) Engine coolant temperature sensor
Vehicle speed sensor
Frequency of operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Engine speed 950 to 1600 rpm
Vehicle speed 20 km/h (12.4 mph) or more
Intake air temperature -10°C (14°F) or higher

TYPICAL MALFUNCTION THRESHOLDS

Manifold pressure change Less than 1 kPa(gauge) [7.5 mmHg(gauge)]
At engine speed 1050 rpm

CONFIRMATION DRIVING PATTERN

A249360E30
4.448,2.833 4.104,3.125 false 5.365,2.927 6.063,3.26 0.698,0.333 10 false 5 seconds or more 1.948,2.052 2.229,2.313 0.281,0.26 10 false [A] 2.781,1.573 3.063,1.833 0.281,0.26 10 false [B] 4.354,2.052 4.635,2.313 0.281,0.26 10 false [C] 5.635,1.594 5.917,1.854 0.281,0.26 10 false [E] 5.073,1.042 5.292,1.24 0.219,0.198 10 false [D] 2.5,2.938 3.813,3.104 1.313,0.167 10 false 10 seconds or more 1.667,2.927 2.448,3.094 0.781,0.167 10 false Warming up 0.573,1.156 1.156,1.333 0.583,0.177 10 false 60 km/h 0.729,2.146 1.219,2.385 0.49,0.24 10 false Idling 0.208,2.406 1.094,2.76 0.885,0.354 10 false Power Switch on (IG) 6.156,3.354 6.438,3.615 0.281,0.26 10 false [F] 3.917,3.146 5.188,3.302 1.271,0.156 10 false 30 seconds or more

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

8.

Accelerate the vehicle to 60 km/h (37 mph) or more by depressing the accelerator pedal for at least 10 seconds [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

When accelerating the vehicle, depress the accelerator pedal more than normal to start the engine.


9.

Idle the engine for 30 seconds or more [C].

10.

Accelerate the vehicle to 60 km/h (37 mph) with shift position (B) selected [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Perform fuel cut operation for 5 seconds or more, with the accelerator pedal fully released [E].

HINT:

When fuel cut is operating "Idle Fuel Cut" in Data List is ON.


12.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Power train / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P0401.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows NORMAL, the system is normal.

·

If the DTC judgment result is INCOMPLETE or N/A, perform steps [D] and [E] again.




CAUTION / NOTICE / HINT

HINT:
·

By using the Control the EGR Step Position Active Test, the operation of the EGR valve can be checked.

·

If the EGR valve is normal and is opened using the Active Test, the Data List value changes as follows.

Data List Change in Data List when Number of Steps is Increased Using Control the EGR Step Position Active Test
MAP Pressure rises

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0401)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTC.

Result
Result Proceed to
DTC P0401 is output A
DTC P0401 and other DTCs are output B

HINT:

If any DTCs other than P0401 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off and park (P) or neutral (N) selected.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / All Data / MAP.


g.

Check the MAP value in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.





OK

3.INSPECT EGR VALVE ASSEMBLY

NG

4.REPLACE EGR VALVE ASSEMBLY
3.INSPECT EGR VALVE ASSEMBLY
a.

Check if the EGR valve are clogged with deposits.


b.

Check if the EGR valve is closed.

OK:

EGR valve is closed and no deposits.


Result
Result Proceed to
NG A
OK B



A

4.REPLACE EGR VALVE ASSEMBLY

B

5.CHECK FOR DEPOSIT (INTAKE PORT TO EGR VALVE ASSEMBLY)
4.REPLACE EGR VALVE ASSEMBLY
a.

Replace the EGR valve assembly (See page Engine / Hybrid System>2ZR-FXE (EMISSION CONTROL)>EGR VALVE>REMOVAL).



NEXT

5.CHECK FOR DEPOSIT (INTAKE PORT TO EGR VALVE ASSEMBLY)
5.CHECK FOR DEPOSIT (INTAKE PORT TO EGR VALVE ASSEMBLY)
A215831

a.

Check for exhaust leaks at each connection point.


b.

Check for cracks, damage, and clogs in the pipes between the intake manifold and the EGR valve assembly.


c.

This check may require the removal of components.


d.

Check if there is a build-up of deposits in the EGR valve or pipes.

OK:

No deposits.




OK

6.CHECK FOR DEPOSIT (EXHAUST MANIFOLD SUB-ASSEMBLY TO EGR VALVE ASSEMBLY)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK FOR DEPOSIT (EXHAUST MANIFOLD SUB-ASSEMBLY TO EGR VALVE ASSEMBLY)
A215832

a.

Check for exhaust leaks at each connection point.


b.

Check for cracks, damage, and clogs in the pipes between the exhaust manifold sub-assembly and the EGR valve assembly.


c.

This check may require the removal of components.


d.

Check if there is a build-up of deposits in the EGR valve or pipes.

OK:

No deposits.




OK

7.INSPECT EGR PIPE WITH COOLER SUB-ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

7.INSPECT EGR PIPE WITH COOLER SUB-ASSEMBLY
a.

Check for blockage of the EGR pipe with cooler sub-assembly.



OK

8.READ VALUE USING GTS (MANIFOLD ABSOLUTE PRESSURE SENSOR)

NG

REPLACE EGR PIPE WITH COOLER SUB-ASSEMBLY

8.READ VALUE USING GTS (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAP.


e.

Read the MAP value.

Standard:
Condition GTS Display
Power switch on (IG) 80 to 110 kPa(abs) [600 to 825 mmHg(abs)]



f.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


g.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAP.


i.

Read the MAP value when idling the engine with the A/C switch and all accessory switches should be off and shift position in P or N.

Standard:
Engine Condition GTS Display
Idling Less than 80 kPa(abs) [600 mmHg(abs)]


Result
Result Proceed to
NG A
OK B



A

9.CHECK INTAKE SYSTEM

B

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks (See page Engine / Hybrid System>2ZR-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leaks in intake system.




OK

10.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

REPAIR OR REPLACE INTAKE SYSTEM

10.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor (See page Engine / Hybrid System>2ZR-FXE (EMISSION CONTROL)>VACUUM SENSOR>REMOVAL).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


j.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.




k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P0401.


m.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit





NEXT

END