Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

A379048E02
1.281,1.604 1.615,1.396 false 0.385,0.417 0.813,0.698 0.427,0.281 10 false (kΩ) 0.177,0.229 0.938,0.552 0.76,0.323 10 false Resistance 0.094,0.01 0.583,0.292 0.49,0.281 10 false Fig. 1: 0.313,0.573 0.74,0.854 0.427,0.281 10 false 30 0.313,0.75 0.74,1.031 0.427,0.281 10 false 20 0.302,1.094 0.729,1.375 0.427,0.281 10 false 10 0.365,1.448 0.792,1.729 0.427,0.281 10 false 5 0.354,1.677 0.781,1.958 0.427,0.281 10 false 3 0.354,1.896 0.781,2.177 0.427,0.281 10 false 2 0.375,2.24 0.802,2.521 0.427,0.281 10 false 1 0.292,3.396 0.719,3.677 0.427,0.281 10 false 0.1 0.281,3.063 0.708,3.344 0.427,0.281 10 false 0.2 0.281,2.823 0.708,3.104 0.427,0.281 10 false 0.3 0.292,2.594 0.719,2.875 0.427,0.281 10 false 0.5 0.604,3.781 1.031,4.063 0.427,0.281 10 false -20 1.052,3.792 1.479,4.073 0.427,0.281 10 false 0 1.406,3.792 1.833,4.073 0.427,0.281 10 false 20 1.771,3.792 2.198,4.073 0.427,0.281 10 false 40 2.167,3.792 2.594,4.073 0.427,0.281 10 false 60 2.542,3.792 2.969,4.073 0.427,0.281 10 false 80 2.854,3.792 3.281,4.073 0.427,0.281 10 false 100 3.146,3.781 3.427,4.073 0.281,0.292 10 false (°C) 3.146,3.979 3.427,4.271 0.281,0.292 10 false (°F) 1.563,4.365 2.604,4.646 1.042,0.281 10 false Temperature 0.677,3.948 1.104,4.229 0.427,0.281 10 false -4 1,3.948 1.427,4.229 0.427,0.281 10 false 32 1.417,3.969 1.844,4.25 0.427,0.281 10 false 68 1.74,3.958 2.167,4.24 0.427,0.281 10 false 104 2.49,3.948 2.917,4.229 0.427,0.281 10 false 176 2.125,3.958 2.552,4.24 0.427,0.281 10 false 140 2.875,3.958 3.302,4.24 0.427,0.281 10 false 212 1.656,1.302 2.417,1.625 0.76,0.323 10 false Acceptable

The intake air temperature sensor, mounted on the mass air flow meter sub-assembly, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (See Fig. 1).

The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When DTC P0112 or P0113 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.



DTC No. DTC Detection Condition Trouble Area
P0112 A short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


P0113 An open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM



HINT:

When any of these DTCs are output, check the intake air temperature using the GTS. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit

MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor circuit and stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Wait 0.5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0112 or P0113.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A259009E12
1.615,1.479 1.958,1.719 0.344,0.24 10 false THA 1.729,2.094 1.958,2.323 0.229,0.229 10 false E2 2,1.479 2.094,1.625 0.094,0.146 10 false 1 2.01,2.094 2.115,2.271 0.104,0.177 10 false 2 0.417,2.792 0.656,2.958 0.24,0.167 10 false D5 0.417,2.958 2.948,3.583 2.531,0.625 10 false Intake Air Temperature Sensor (Built into Mass Air Flow Meter Sub-assembly) 5.406,1.479 5.729,1.656 0.323,0.177 10 false THA 5.417,2.083 5.844,2.24 0.427,0.156 10 false ETHA 5.813,3.115 6.104,3.271 0.292,0.156 10 false D28 5.083,1.479 5.365,1.646 0.281,0.167 10 false 116 5.125,2.073 5.323,2.271 0.198,0.198 10 false 93 6.104,3.115 6.458,3.26 0.354,0.146 10 false ECM 6.042,1.073 6.302,1.229 0.26,0.156 10 false 5 V 5.99,1.365 6.271,1.521 0.281,0.156 10 false R

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.


e.

Read the value displayed on the GTS.

OK:

Same as actual intake air temperature.


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) B
Same as actual intake air temperature C

HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).


·

If there is a short circuit, the GTS indicates 140°C (284°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the mass air flow meter sub-assembly connector.

U190505E02
4.708,2.375 5.052,1.906 false 5.438,2.385 5.229,1.906 false 0.948,2.021 1.177,2.229 0.229,0.208 10 false *1 2.802,2.021 3,2.188 0.198,0.167 10 false *2 2.656,1.333 2.948,1.5 0.292,0.167 10 false THA 1.406,1.333 1.698,1.5 0.292,0.167 10 false THA 1.521,1.635 1.708,1.802 0.188,0.167 10 false E2 2.656,1.74 3.042,1.906 0.385,0.167 10 false ETHA 4.49,0.125 4.677,0.333 0.188,0.208 10 false *a 4.333,1.771 4.531,1.948 0.198,0.177 10 false D5 4.573,2.396 4.906,2.552 0.333,0.156 10 false THA 5.354,2.396 5.573,2.552 0.219,0.156 10 false E2


Text in Illustration
*1 Mass Air Flow Meter Sub-assembly *2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)
- -

b.

Connect terminals 1 (THA) and 2 (E2) of the mass air flow meter sub-assembly connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.


g.

Read the value displayed on the GTS.

Standard value:

140°C (284°F)




OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D5-1 (THA) - D28-116 (THA) Always Below 1 Ω
D5-2 (E2) - D28-93 (ETHA) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A194323E03
0.325,0.339 0.516,0.516 0.191,0.176 10 *1 2.25,0.339 2.436,0.502 0.186,0.163 10 *2 2.537,1.328 2.866,1.477 0.330,0.149 10 THA 2.499,1.766 2.922,1.915 0.422,0.149 10 ETHA

Disconnect the mass air flow meter sub-assembly connector.

Text in Illustration
*1 Mass Air Flow Meter Sub-assembly
*2 ECM


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.


f.

Read the value displayed on the GTS.

Standard value:

-40°C (-40°F)




OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D5-1 (THA) or D28-116 (THA) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR