Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2016.05–2020.08
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  U0293  Lost Communication with HV ECU  


MONITOR DESCRIPTION

The Controller Area Network (CAN) is a serial data communication system for real-time application. It is a multiplex communication system designed for on-vehicle use that provides a superior communication speed of 500 kbps and a capability to detect malfunctions. Through the combination of the CANH and CANL bus lines, the CAN is able to maintain communication based on differential voltage.

DTC No. DTC Detection Condition Trouble Area
U0293 Communication with hybrid vehicle control ECU is interrupted (1 trip detection logic).
·

Wire harness

·

Hybrid vehicle control ECU



MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: U0293.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A217287E52
5,3.198 5.417,3.385 0.417,0.188 10 false A57 5.365,3.198 5.688,3.354 0.323,0.156 10 false ECM 4.792,1.375 5.24,1.552 0.448,0.177 10 false CANH 1.979,1.375 2.427,1.552 0.448,0.177 10 false CA1H 1.979,1.781 2.427,1.958 0.448,0.177 10 false CA1L 4.792,1.781 5.24,1.958 0.448,0.177 10 false CANL 4.792,2.25 5.24,2.427 0.448,0.177 10 false CANP 1.99,2.25 2.438,2.427 0.448,0.177 10 false CA3P 1.99,2.688 2.438,2.865 0.448,0.177 10 false CA3N 4.792,2.677 5.24,2.854 0.448,0.177 10 false CANN 4.542,1.208 4.719,1.375 0.177,0.167 10 false 13 2.448,1.208 2.625,1.375 0.177,0.167 10 false 25 2.448,2.063 2.625,2.229 0.177,0.167 10 false 31 2.448,2.49 2.625,2.656 0.177,0.167 10 false 30 2.448,1.594 2.625,1.76 0.177,0.167 10 false 24 4.542,2.063 4.719,2.229 0.177,0.167 10 false 12 4.604,1.594 4.781,1.76 0.177,0.167 10 false 5 4.604,2.49 4.802,2.656 0.198,0.167 10 false 4 0.969,3.156 1.365,3.344 0.396,0.188 10 false L6 0.958,3.333 2.656,3.729 1.698,0.396 10 false Hybrid Vehicle Control ECU 1.031,4.031 2.052,4.292 1.021,0.26 10 false : CAN Bus Line

PROCEDURE

1.REFER TO CAN COMMUNICATION SYSTEM

Refer to the CAN Communication System.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



NEXT

END