Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P261B  Engine Coolant Pump "B" Control Malfunction  P261C  Engine Coolant Pump "B" Control Circuit Low  P261D  Engine Coolant Pump "B" Control Circuit High  


DESCRIPTION

The ECM controls the engine water pump assembly by calculating the necessary amount of coolant flow based on engine coolant temperature, engine speed and vehicle speed information. The speed of the engine water pump assembly is controlled steplessly using a duty cycle signal sent from the ECM. This optimal control enhances warm-up performance and reduces cooling losses, thus reducing the specific fuel consumption of the engine.

DTC No. DTC Detection Condition Trouble Area
P261B Engine water pump assembly speed is less than 900 rpm while the engine water pump assembly is operating (1 trip detection logic).
·

Open or short in engine water pump assembly circuit

·

Engine water pump assembly

·

ECM


P261C Engine water pump assembly output voltage is less than specified value while the engine water pump assembly is operating (1 trip detection logic).
·

Short in engine water pump assembly circuit

·

Engine water pump assembly

·

ECM


P261D Engine water pump assembly output voltage is higher than specified value while the engine water pump assembly is operating (1 trip detection logic).
·

Open in engine water pump assembly circuit

·

Engine water pump assembly

·

ECM



MONITOR DESCRIPTION

The ECM calculates the speed of the engine water pump assembly using a duty cycle signal sent from the engine water pump assembly. When the speed of the engine water pump assembly becomes less than 900 rpm while it is operating, the ECM detects the malfunction and stores DTC P261B.

The engine water pump assembly operates steplessly based on a duty cycle signal sent from the ECM. If actual drive duty cycle ratio does not correspond to the target drive duty cycle of the engine water pump assembly, the ECM detects the malfunction and stores DTC P261C or P261D.

MONITOR STRATEGY

Required Sensors/Components Engine water pump assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher).

8.

Idle the engine for 20 seconds or more [A].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P261B, P261C or P261D.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.




WIRING DIAGRAM

A259182E09
4.292,2.167 5.604,2.531 1.313,0.365 10 false Engine Water Pump Assembly 4.292,2 4.615,2.188 0.323,0.188 10 false D13 5.125,1.104 5.615,1.354 0.49,0.25 10 false NWP 4.344,1.083 4.698,1.26 0.354,0.177 10 false +B 5.125,1.688 5.615,1.885 0.49,0.198 10 false SWP 5.563,1.583 5.698,1.76 0.135,0.177 10 false 4 4.156,1.594 4.292,1.771 0.135,0.177 10 false 5 4.156,0.99 4.292,1.167 0.135,0.177 10 false 1 5.552,0.99 5.688,1.167 0.135,0.177 10 false 2 4.344,1.677 4.854,1.885 0.51,0.208 10 false PGND 5.833,1.583 6.063,1.75 0.229,0.167 10 false 10 5.844,0.99 6.073,1.156 0.229,0.167 10 false 11 6.094,1.677 6.552,1.875 0.458,0.198 10 false WPO 6.094,1.083 6.698,1.385 0.604,0.302 10 false WPI 6.083,3.99 6.656,4.26 0.573,0.271 10 false MREL 5.896,3.875 6.146,4.115 0.25,0.24 10 false 6 6.417,4.51 6.896,4.729 0.479,0.219 10 false ECM 1.625,1.76 2.25,2 0.625,0.24 10 false ENG W/P 0.583,1.229 1.208,1.469 0.625,0.24 10 false ENG W/P 1.573,1.448 1.719,1.635 0.146,0.188 10 false 2 2.146,1.438 2.292,1.583 0.146,0.146 10 false 1 2.167,0.99 2.292,1.167 0.125,0.177 10 false 5 1.573,1 1.677,1.167 0.104,0.167 10 false 3 2.677,3.115 3.302,3.281 0.625,0.167 10 false EFI MAIN 1.854,3.094 2.531,3.406 0.677,0.313 10 false EFI MAIN 1.188,4.323 1.49,4.521 0.302,0.198 10 false P/I 1 0.531,4.479 0.979,4.677 0.448,0.198 10 false MAIN 0.688,5.063 1.75,5.25 1.063,0.188 10 false Auxiliary Battery 6.104,4.51 6.5,4.75 0.396,0.24 10 false A57 0.531,2.375 1.01,2.615 0.479,0.24 10 false DC/DC 1.031,3.604 2.5,4 1.469,0.396 10 false No. 2 Integration Relay 1.167,2.875 1.396,3.052 0.229,0.177 10 false 1B 1.333,2.083 1.563,2.26 0.229,0.177 10 false 1B 1.208,2.688 1.354,2.854 0.146,0.167 10 false 2 2.5,3.385 2.74,3.552 0.24,0.167 10 false 1C 2.792,3.385 2.948,3.552 0.156,0.167 10 false 1 3.083,2.865 3.281,3.031 0.198,0.167 10 false 1B 3.135,2.677 3.26,2.833 0.125,0.156 10 false 3 1.646,2.094 1.802,2.25 0.156,0.156 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE ELECTRIC WATER PUMP)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Electric Water Pump.


e.

Touch the engine water pump and check that the pump assembly is operating (vibrating).

OK:

The engine water pump assembly is operating (vibrating).




OK

2.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM)

NG

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ENGINE WATER PUMP ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM)
HINT:

Confirm a good connection at the engine water pump assembly and ECM connectors.


a.

Disconnect the engine water pump assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D13-2 (NWP) - A57-11 (WPI) Always Below 1 Ω
D13-4 (SWP) - A57-10 (WPO) Always Below 1 Ω
D13-2 (NWP) or A57-11 (WPI) - Body ground Always 10 kΩ or higher
D13-4 (SWP) or A57-10 (WPO) - Body ground Always 10 kΩ or higher




OK

3.CHECK TERMINAL VOLTAGE (WPI VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (WPI VOLTAGE)
a.
U110516E03
1.74,2.083 2.438,2.563 false 0.604,2.094 0.875,2.271 0.271,0.177 10 false D13 2.302,2.583 2.719,2.792 0.417,0.208 10 false NWP 0.469,0.146 0.677,0.365 0.208,0.219 10 false *a

Disconnect the engine water pump assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D13-2 (NWP) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Engine Water Pump Assembly)



OK

REPLACE ENGINE WATER PUMP ASSEMBLY

NG

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ENGINE WATER PUMP ASSEMBLY)
HINT:

Confirm a good connection at the engine water pump assembly and ECM connectors.


a.
U110517E03
1.385,2.083 1.094,2.74 false 0.594,2.104 0.865,2.281 0.271,0.177 10 false D13 0.969,2.76 1.208,2.969 0.24,0.208 10 false +B 0.469,0.146 0.677,0.365 0.208,0.219 10 false *a

Disconnect the engine water pump assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D13-1 (+B) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Engine Water Pump Assembly)



OK

5.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - BODY GROUND)

NG

9.INSPECT RELAY (ENG W/P RELAY)
5.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect the engine water pump assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D13-5 (PGND) - Body ground Always Below 1 Ω




OK

6.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM)
a.

Disconnect the engine water pump assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D13-2 (NWP) - A57-11 (WPI) Always Below 1 Ω
D13-4 (SWP) - A57-10 (WPO) Always Below 1 Ω
D13-2 (NWP) or A57-11 (WPI) - Body ground Always 10 kΩ or higher
D13-4 (SWP) or A57-10 (WPO) - Body ground Always 10 kΩ or higher




OK

7.REPLACE ENGINE WATER PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE ENGINE WATER PUMP ASSEMBLY
a.

Replace the engine water pump assembly (See page Engine / Hybrid System>2ZR-FXE (COOLING)>WATER PUMP>REMOVAL).



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P261B, P261C OR P261D)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P261B, P261C OR P261D)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
DTC P261B, P261C or P261D is output A
DTC is not output B



A

B

END

9.INSPECT RELAY (ENG W/P RELAY)
a.
A234567E01
2.32,0.531 2.424,0.680 0.104,0.149 10 2 2.32,1.557 2.424,1.706 0.104,0.149 10 1 2.755,0.531 2.858,0.680 0.104,0.149 10 3 2.755,1.557 2.858,1.706 0.104,0.149 10 5 2.375,0.9 2.375,0.689 false 2.373,1.318 2.373,1.557 false 2.628,1.218 2.792,1.557 false 2.899,1 2.8,0.695 false

Remove the ENG W/P relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 No auxiliary battery voltage applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω




OK

10.CHECK HARNESS AND CONNECTOR (ENG W/P RELAY - ENGINE WATER PUMP ASSEMBLY)

NG

REPLACE RELAY (ENG W/P RELAY)

10.CHECK HARNESS AND CONNECTOR (ENG W/P RELAY - ENGINE WATER PUMP ASSEMBLY)
a.

Remove the ENG W/P relay from the engine room relay block and junction block assembly.


b.

Disconnect the engine water pump assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ENG W/P relay terminal 5 - D13-1 (+B) Always Below 1 Ω
ENG W/P relay terminal 5 or D13-1 (+B) - Body ground Always 10 kΩ or higher




OK

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ENG W/P RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ENG W/P RELAY)
a.
A259183E01
0.222,0.162 0.401,0.322 0.179,0.161 10 *1 2.113,0.763 2.292,0.924 0.179,0.161 10 *2

Remove the ENG W/P relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ENG W/P relay terminal 3 - Body ground Always 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 ENG W/P Relay



OK

12.CHECK HARNESS AND CONNECTOR (ENG W/P RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - ENG W/P RELAY)

12.CHECK HARNESS AND CONNECTOR (ENG W/P RELAY - BODY GROUND)
a.

Remove the ENG W/P relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ENG W/P relay terminal 1 - Body ground Always Below 1 Ω




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENG W/P RELAY - EFI MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR