Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.03–2012.10
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3110-223  IGCT Relay Malfunction  


DESCRIPTION

The power management control ECU monitors the IGCT relay and detects the following malfunction.

DTC No. INF Code DTC Detection Condition Trouble Area
P3110 223 There is a short to +B in the IGCT relay or the IGCT relay is stuck closed.
·

Wire harness or connector

·

IGCT relay

·

Power management control ECU



WIRING DIAGRAM

A379102E01
0.479,1.125 1.302,1.427 0.823,0.302 10 false IGCT 0.5,1.802 1.323,2.104 0.823,0.302 10 false MAIN 0.604,2.604 1.844,2.969 1.24,0.365 10 false Auxiliary Battery 2.531,1.198 3.354,1.5 0.823,0.302 10 false 2 2.531,0.75 3.354,1.052 0.823,0.302 10 false 3 3.417,0.74 4.24,1.042 0.823,0.302 10 false 5 3.417,1.188 4.24,1.49 0.823,0.302 10 false 1 3.521,1.021 4.344,1.323 0.823,0.302 10 false IGCT NO. 2 4.948,0.458 5.771,0.76 0.823,0.302 10 false A22 4.969,0.865 5.792,1.167 0.823,0.302 10 false A21 5.021,0.25 5.844,0.552 0.823,0.302 10 false 5 5.031,0.667 5.854,0.969 0.823,0.302 10 false 2 5.042,1.094 5.865,1.396 0.823,0.302 10 false 6 5.323,0.438 6.146,0.74 0.823,0.302 10 false +B1 5.313,1.313 6.135,1.615 0.823,0.302 10 false MREL 5.083,2.854 6.344,3.292 1.26,0.438 10 false Power Management Control ECU 2.844,1.708 3.667,2.01 0.823,0.302 10 false IGCT 4.958,1.302 5.781,1.604 0.823,0.302 10 false A22 5.313,0.865 6.135,1.167 0.823,0.302 10 false +B2

CAUTION / NOTICE / HINT

HINT:
·

If the auxiliary battery voltage is applied to terminal +B1 or +B2 of the power management control ECU, even though the power switch is off, the circuit is shorted to +B.

·

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

(a)

Turn the power switch on (IG) and wait for 15 seconds or more.

(b)

Turn the power switch off and wait for 30 seconds or more.




PROCEDURE

1.INSPECT RELAY (IGCT)
a.

Remove the IGCT relay from the engine room relay block and junction block assembly.


b.
A253297E01
0.165,0.068 0.398,0.266 0.232,0.198 10 *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage is not applied between terminals 1 and 2 10 kΩ or higher


Text in Illustration
*1 IGCT Relay


c.

Install the IGCT relay.



OK

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)

NG

REPLACE RELAY (IGCT)

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)
a.

Remove the IGCT relay from the engine room relay block and junction block assembly.


b.

Disconnect the A21 and A22 power management control ECU connectors.


c.

Measure the voltage according to the value(s) in the table below.

U190668E02
1.521,2.094 1.708,2.635 false 1.885,2.083 2.26,2.646 false 0.448,0.333 0.708,0.635 0.26,0.302 10 false *a 3.99,0.396 4.188,0.667 0.198,0.271 10 false *1 5.823,2.083 6.021,2.354 0.198,0.271 10 false *2 1.583,2.656 1.906,2.896 0.323,0.24 10 false +B2 2.177,2.646 2.469,2.865 0.292,0.219 10 false +B1 1.271,2.885 1.542,3.052 0.271,0.167 10 false A21 1.885,2.896 2.156,3.063 0.271,0.167 10 false A22

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly *2 IGCT relay
*a Rear view of wire harness connector
(to Power Management Control ECU)
- -

Standard Voltage:
Tester Connection Condition Specified Condition
A22-5 (+B1), A21-2 (+B2) or 5 (IGCT relay) - Body ground Power switch off Below 1 V



d.

Install the IGCT relay.


e.

Reconnect the A21 and A22 power management control ECU connectors.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR