Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.03–2012.10
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A78-282  Drive Motor "A" Inverter Performance  


DESCRIPTION

For a description of the inverter (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A78-266).

If an overvoltage occurs in the motor inverter or generator inverter, the MG ECU detects it and transmits this information to the power management control ECU.

DTC No. INF Code DTC Detection Condition Trouble Area
P0A78 282 Motor inverter overvoltage signal detection (circuit malfunction) Inverter with converter assembly

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals of the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clean the DTCs and perform the following procedure to check that DTCs are not output.

1.

With the vehicle engine stopped, the power switch on (READY) and park (P) selected, depress the accelerator pedal to start the engine.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
P0A78-282 is set before any of the DTCs in the table below are set. A
Any of the DTCs including pending DTCs in the table 1 below are set before P0A78-282 is set. B
Any of the DTCs including pending DTCs in the table 2 below are set before P0A78-282 is set. C


Table 1
DTC No. Relevant Diagnosis
P0AC0-817 Hybrid Battery Pack Current Sensor Circuit Range / Performance
P3000-388, 389, 603 HV Battery Malfunction
P3004-131, 133 High Voltage Power Resource

Table 2
DTC No. Relevant Diagnosis
P0A7F-123 Hybrid Battery Pack Deterioration
P0A80-123 Replace Hybrid Battery Pack
P0A95-123 High Voltage Fuse
P0A9C-123 Hybrid Battery Temperature Sensor "A" Range / Performance
P0A9D-123 Hybrid Battery Temperature Sensor "A" Circuit Low
P0A9E-123 Hybrid Battery Temperature Sensor "A" Circuit High
P0ABF-123 Hybrid Battery Pack Current Sensor Circuit
P0AC0-123 Hybrid Battery Pack Current Sensor Circuit Range / Performance
P0AC1-123 Hybrid Battery Pack Current Sensor Circuit Low
P0AC2-123 Hybrid Battery Pack Current Sensor Circuit High
P0AC6-123 Hybrid Battery Temperature Sensor "B" Range / Performance
P0AC7-123 Hybrid Battery Temperature Sensor "B" Circuit Low
P0AC8-123 Hybrid Battery Temperature Sensor "B" Circuit High
P0ACB-123 Hybrid Battery Temperature Sensor "C" Range / Performance
P0ACC-123 Hybrid Battery Temperature Sensor "C" Circuit Low
P0ACD-123 Hybrid Battery Temperature Sensor "C" Circuit High
P0AE9-123 Hybrid Battery Temperature Sensor "D" Range / Performance
P0AEA-123 Hybrid Battery Temperature Sensor "D" Circuit Low
P0AEB-123 Hybrid Battery Temperature Sensor "D" Circuit High
P0AFC-123 Hybrid Battery Pack Sensor Module
P0B10-123 Hybrid Battery Pack Current Sensor "B" Circuit Low
P0B11-123 Hybrid Battery Pack Current Sensor "B" Circuit High
P0B13-123 Hybrid Battery Pack Current Sensor "A"/"B" Correlation
P0BC3-123 Hybrid Battery Temperature Sensor "E" Range / Performance
P0BC4-123 Hybrid Battery Temperature Sensor "E" Circuit Low
P0BC5-123 Hybrid Battery Temperature Sensor "E" Circuit High
P0C34-123 Hybrid Battery Temperature Sensor "F" Range / Performance
P0C35-123 Hybrid Battery Temperature Sensor "F" Circuit Low
P0C36-123 Hybrid Battery Temperature Sensor "F" Circuit High
P3011-123 Battery Block 1 Becomes Weak
P3012-123 Battery Block 2 Becomes Weak
P3013-123 Battery Block 3 Becomes Weak
P3014-123 Battery Block 4 Becomes Weak
P3015-123 Battery Block 5 Becomes Weak
P3016-123 Battery Block 6 Becomes Weak
P3017-123 Battery Block 7 Becomes Weak
P3018-123 Battery Block 8 Becomes Weak
P301A-123 Open in Hybrid Battery Cell Voltage Detection Circuit
P301B-123 Hybrid Battery Cell Voltage Detection Circuit Range/Performance
P3065-123 Hybrid Battery Temperature Sensor Range/Performance Stuck "A"
P306A-123 Hybrid Battery Temperature Sensor Range / Performance Stuck "B"
P31AA-123 Hybrid Battery Cell High Voltage
P31AB-123 Hybrid Battery Cell Low Voltage
P31AC-123 Hybrid Battery Cell Extreme High Voltage
P31B3-123 Hybrid Battery Voltage High
P31B4-123 Extreme Charging Current Caused by Hybrid Battery High Voltage
P31B5-123 Abnormal Current Caused by Continuous Current from Hybrid Battery
U029A-123 Lost Communication with Hybrid Battery Pack Sensor Module

HINT:
·

Refer to the freeze frame data to determine the order in which the DTCs were set.

·

P0A78-282 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.




e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

C

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

CONNECT SECURELY