Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.03–2012.10
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A90-251  Drive Motor "A" Performance  


DESCRIPTION

When three-phase alternating current flows through the three-phase windings of the stator coil, a rotating magnetic field is generated in motor. The system controls the rotation of the magnetic field in accordance with the rotating position and speed of the rotor. As a result, the permanent magnets provided in the rotor are pulled in the direction of rotation, generating torque. The generated torque is almost proportional to the amount of current. The system controls motor speed by regulating the frequency of the alternating current. Furthermore, the system properly controls the rotating magnetic field and the angle of the rotor magnets in order to generate high torque in an efficient manner, even at high speeds.

A352258E01
1.854,1.271 2.688,1.406 false 3.177,3.396 3.417,2.625 false 5.031,1.844 3.875,1.917 false 4.865,1.271 3.479,1.917 false 4.802,0.583 3.417,1.229 false 2.323,0.177 3.396,0.375 1.073,0.198 10 false U Phase 0.354,1.167 2.427,1.583 2.073,0.417 10 false Rotating Magnetic Field 1.708,2.542 2.781,2.74 1.073,0.198 10 false # 1.271,3.208 2.344,3.406 1.073,0.198 10 false V Phase 2.958,3.427 5.031,3.76 2.073,0.333 10 false Attraction 4.604,3.198 5.677,3.396 1.073,0.198 10 false # 5.24,2.49 6.313,2.688 1.073,0.198 10 false W Phase 5.646,3.063 6.719,3.26 1.073,0.198 10 false : from inverter 5.521,3.375 6.594,3.573 1.073,0.198 10 false # : wired in motor 5.104,1.781 6.177,1.979 1.073,0.198 10 false Reaction 4.927,1.167 6,1.365 1.073,0.198 10 false Rotor 3.698,0.302 4.771,0.5 1.073,0.198 10 false # 4.844,0.479 5.917,0.677 1.073,0.198 10 false Stator Coil 3.438,1.708 4.51,1.906 1.073,0.198 10 false N 3.208,2.313 4.281,2.51 1.073,0.198 10 false S

DTC No. INF Code DTC Detection Condition Trouble Area
P0A90 251 Motor magnetic force deterioration or same phase short circuit
·

Hybrid vehicle motor assembly

·

Motor cable

·

Inverter with converter assembly



CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle until the cumulative traveling time driving a vehicle speed of 25 mph (40 km/h) or more is a few minutes. (It is not required to keep driving at 25 mph (40 km/h) or more.)



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTC P0A90-251 only is output, or DTCs other than the ones in the table below are also output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P0A1A (all INF codes)*1 Generator Control Module
P0A1B (all INF codes)*1 Drive Motor "A" Control Module
P0A1D (all INF codes)*1 Hybrid Powertrain Control Module
P0A60 (all INF codes)*1 Drive Motor "A" Phase V Current
P0A63 (all INF codes)*1 Drive Motor "A" Phase W Current
P0A72 (all INF codes)*1 Generator Phase V Current
P0A75 (all INF codes)*1 Generator Phase W Current
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A40-500 Drive Motor "A" Position Sensor Circuit Range/Performance
P0A41-245 Drive Motor "A" Position Sensor Circuit Low
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513 Generator Position Sensor Circuit Range/Performance
P0A4D-255 Generator Position Sensor Circuit Low
P0A51-174 Drive Motor "A" Current Sensor Circuit
P0A78-202, 266, 267, 282, 306, 586 Drive Motor "A" Inverter Performance
P0A7A-344 Generator Inverter Performance
P0A90-509 Drive Motor "A" Performance
P0A92-521 Hybrid Generator Performance
P0A93-346 Inverter Cooling System Performance
P0A94-585, 587, 589, 590 DC / DC Converter Performance
P0AA6 (all INF codes)*1 Hybrid Battery Voltage System Isolation Fault
P0C76-523 Hybrid Battery System Discharge Time Too Long
P3004-132 High Voltage Power Resource
P3233-750 Open or Short to B+ in Blocking of HV Gate Connection

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0A90-251 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.




e.

Turn the power switch off.



A

2.PERFORM SIMULATION TEST

B

2.PERFORM SIMULATION TEST
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Test-drive the vehicle at a speed of 40 km/h (25 mph) for approximately 1 minute.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check if DTCs are output.

Result:
Result Proceed to
P0A90-251 is output or no DTC is output. A
Any DTCs other than P0A90-251 are output. B



f.

Turn the power switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

4.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

NG

CONNECT SECURELY

4.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

A

5.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

5.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

OK

NG

6.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)
6.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

A

7.CHECK MOTOR CABLE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY