Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A90-251  Drive Motor "A" Performance  


DESCRIPTION

When three-phase alternating current flows through the three-phase windings of the stator coil, a rotating magnetic field is generated in motor. The system controls the rotation of the magnetic field in accordance with the rotating position and speed of the rotor. As a result, the permanent magnets provided in the rotor are pulled in the direction of rotation, generating torque. The generated torque is almost proportional to the amount of current. The system controls motor speed by regulating the frequency of the alternating current. Furthermore, the system properly controls the rotating magnetic field and the angle of the rotor magnets in order to generate high torque in an efficient manner, even at high speeds.

A352258E01
1.854,1.271 2.688,1.406 false 3.177,3.396 3.417,2.625 false 5.031,1.844 3.875,1.917 false 4.865,1.271 3.479,1.917 false 4.802,0.583 3.417,1.229 false 2.323,0.177 3.396,0.375 1.073,0.198 10 false U Phase 0.354,1.167 2.427,1.583 2.073,0.417 10 false Rotating Magnetic Field 1.708,2.542 2.781,2.74 1.073,0.198 10 false # 1.271,3.208 2.344,3.406 1.073,0.198 10 false V Phase 2.958,3.427 5.031,3.76 2.073,0.333 10 false Attraction 4.604,3.198 5.677,3.396 1.073,0.198 10 false # 5.24,2.49 6.313,2.688 1.073,0.198 10 false W Phase 5.646,3.063 6.719,3.26 1.073,0.198 10 false : from inverter 5.521,3.375 6.594,3.573 1.073,0.198 10 false # : wired in motor 5.104,1.781 6.177,1.979 1.073,0.198 10 false Reaction 4.927,1.167 6,1.365 1.073,0.198 10 false Rotor 3.698,0.302 4.771,0.5 1.073,0.198 10 false # 4.844,0.479 5.917,0.677 1.073,0.198 10 false Stator Coil 3.438,1.708 4.51,1.906 1.073,0.198 10 false N 3.208,2.313 4.281,2.51 1.073,0.198 10 false S

DTC No. INF Code DTC Detection Condition Trouble Area
P0A90 251 Motor magnetic force deterioration or same phase short circuit
·

Hybrid vehicle motor assembly

·

Motor cable

·

Inverter with converter assembly



CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle until the cumulative traveling time driving a vehicle speed of 25 mph (40 km/h) or more is a few minutes. (It is not required to keep driving at 25 mph (40 km/h) or more.)



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTC P0A90-251 only is output, or DTCs other than the ones in the table below are also output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P06B0-163 Sensor Power Supply "A" Circuit/Open
P06D6-511 Sensor Reference Voltage "F" Circuit/Open
P06E6-164 Sensor Power Supply "C" Circuit/Open
P0A1A-151, 166, 658, 791 Generator Control Module
P0A1B-198, 786, 794 Drive Motor "A" Control Module
P0A1D (all INF codes)*1 Hybrid Powertrain Control Module
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A40-500 Drive Motor "A" Position Sensor Circuit Range/Performance
P0A41-245 Drive Motor "A" Position Sensor Circuit Low
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513 Generator Position Sensor Circuit Range/Performance
P0A4D-255 Generator Position Sensor Circuit Low
P0A51-174 Drive Motor "A" Current Sensor Circuit
P0A78-202, 282 Drive Motor "A" Inverter Performance
P0A90-509 Drive Motor "A" Performance
P0A92-521 Hybrid Generator Performance
P0A93-346 Inverter Cooling System Performance
P0AA6 (all INF codes)*1 Hybrid Battery Voltage System Isolation Fault
P0BEA-290 Drive Motor "A" Phase V Current Sensor Circuit Range/Performance
P0BEE-298 Drive Motor "A" Phase W Current Sensor Circuit Range/Performance
P0C19-306 Drive Motor "A" Torque Delivered Performance
P0C76-523 Hybrid Battery System Discharge Time Too Long
P0D2E-586 Drive Motor "A" Inverter Voltage Sensor Circuit Range/Performance
P0D2F-266 Drive Motor "A" Inverter Voltage Sensor Circuit Low
P0D30-267 Drive Motor "A" Inverter Performance
P0E05-328 Generator Phase V Current Sensor Circuit Range/Performance
P0E09-336 Generator Phase W Current Sensor Circuit Range/Performance
P0E32-585 DC/DC Converter Voltage Sensor "A" Range/Performance
P0E33-589 DC/DC Converter Voltage Sensor "A" Low
P0E34-590 DC/DC Converter Voltage Sensor "A" High
P0E71-344 Generator Torque Delivered Performance
P1C2A-155 Generator A/D Converter Circuit
P1C2B-192 Drive Motor "A" A/D Converter Circuit
P1C2D-587 Hybrid Battery Voltage / DC/DC Converter Voltage Correlation
P1C3C-294 Drive Motor "A" Phase V Current Sensor Correlation
P1C3D-302 Drive Motor "A" Phase W Current Sensor Correlation
P1C3E-333 Generator Phase V Current Sensor Correlation
P1C3F-341 Generator Phase W Current Sensor Correlation
P1C4A-288 Drive Motor "A" Phase V Current Sensor Sub Circuit Range/Performance
P1C4F-296 Drive Motor "A" Phase W Current Sensor Sub Circuit Range/Performance
P1C54-326 Generator Phase V Current Sensor Sub Circuit Range/Performance
P1C59-334 Generator Phase W Current Sensor Sub Circuit Range/Performance
P1C6D-501 Drive Motor "A" Phase V Current Sensor Offset Range/Performance
P1C6E-502 Drive Motor "A" Phase W Current Sensor Offset Range/Performance
P1C71-515 Generator Phase V Current Sensor Offset Range/Performance
P1C72-516 Generator Phase W Current Sensor Offset Range/Performance
P1C73-512 Sensor Standard Voltage "F" Circuit/Open
P1CA6-156 Generator Control Module Malfunction
P1CA7-193 Drive Motor Control Module Malfunction
P1CAC-200 Generator Position Sensor Angle Malfunction
P1CAD-168 Drive Motor "A" Position Sensor Angle Malfunction
P1CAF-792 Generator Position Sensor REF Signal Cycle Malfunction
P1CB0-795 Drive Motor "A" Position Sensor REF Signal Cycle Malfunction
P1CB2-793 Generator Position Sensor REF Signal Stop Malfunction
P1CB3-796 Drive Motor "A" Position Sensor REF Signal Stop Malfunction
P3004-132 Power Cable Malfunction
P3133-659 Communication Error from Generator to Drive Motor "A"
P3134-661 Communication Error from Drive Motor "A" to Generator
P3233-750 Open or Short to B+ in Blocking of HV Gate Connection

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0A90-251 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.




e.

Turn the power switch off.



A

2.PERFORM SIMULATION TEST

B

2.PERFORM SIMULATION TEST
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Test-drive the vehicle at a speed of 40 km/h (25 mph) for approximately 1 minute.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check if DTCs are output.

Result:
Result Proceed to
P0A90-251 is output or no DTC is output. A
Any DTCs other than P0A90-251 are output. B



f.

Turn the power switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

4.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

NG

CONNECT SECURELY

4.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

A

5.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

5.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

OK

NG

6.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)
6.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

A

7.CHECK MOTOR CABLE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY