Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.03–2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P2532-772  Ignition Switch Run Position Circuit High  


DESCRIPTION

The power source and HV CPU processors and their functions are integrated into the power management control ECU. The power source CPU and HV CPU use CAN communication to communicate with each other inside the power management control ECU. The power source CPU controls the opening and closing of the IG2 relay. The HV CPU detects that the IG2 relay is stuck ON (closed) based on relay operation information received from the power source CPU via CAN communication.

DTC No. INF Code DTC Detection Condition Trouble Area
P2532 772 Voltage is still applied to IG2 terminal although an IG2 relay off command is received from the power source CPU.
·

Wire harness or connector

·

No. 2 integration relay (IG2 relay)

·

Power management control ECU



HINT:

If DTC P2532-772 is stored, the vehicle will turn off.


WIRING DIAGRAM

A262677E01
5.083,2 5.591,2.174 0.508,0.174 10 A22 5.083,2.168 6.425,2.481 1.341,0.313 10 Power Management Control ECU 5.317,0.907 5.825,1.081 0.508,0.174 10 IG2 4.154,0.918 4.374,1.092 0.220,0.174 10 1A 4.196,0.714 4.416,0.889 0.220,0.174 10 4 4.196,1.149 4.416,1.323 0.220,0.174 10 2 4.154,1.359 4.374,1.533 0.220,0.174 10 1A 1.849,0.904 2.069,1.078 0.220,0.174 10 1C 0.231,0.904 1.099,1.240 0.868,0.336 10 from Auxiliary Battery 1.891,0.7 2.111,0.875 0.220,0.174 10 1 1.891,1.135 2.111,1.309 0.220,0.174 10 3 1.849,1.345 2.069,1.519 0.220,0.174 10 1A 5.317,1.346 5.825,1.521 0.508,0.174 10 IG2D 5.121,0.816 5.274,0.990 0.154,0.174 10 1 5.121,1.264 5.274,1.439 0.154,0.174 10 2 3.166,1.78 3.455,1.955 0.289,0.174 10 IG2 2.346,1.059 2.635,1.233 0.289,0.174 10 IG2 2.346,2.18 4.073,2.354 1.727,0.174 10 No. 2 Integration Relay

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 15 seconds or more.

2.

Turn the power switch off and wait for 30 seconds or more.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (+B SHORT)
a.
U154413E02
1.667,2.25 2.01,2.094 false 1.604,2.25 2.021,2.479 false 1.344,2.875 1.615,3.042 0.271,0.167 10 false A22 2.052,2 2.375,2.167 0.323,0.167 10 false IG2 2.063,2.417 2.448,2.594 0.385,0.177 10 false IG2D 0.052,0 0.208,0.167 0.156,0.167 10 false *a

Disconnect the A22 power management control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A22-1 (IG2) - Body ground Power switch off 1 V or less
A22-2 (IG2D) - Body ground Power switch off 1 V or less


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)

Result
Result Proceed to
NG A
OK B


c.

Reconnect the A22 power management control ECU connector.



A

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 2 INTEGRATION RELAY)

B

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 2 INTEGRATION RELAY)
a.

Disconnect the A22 power management control ECU connector.


b.
U154413E02
1.667,2.25 2.01,2.094 false 1.604,2.25 2.021,2.479 false 1.344,2.875 1.615,3.042 0.271,0.167 10 false A22 2.052,2 2.375,2.167 0.323,0.167 10 false IG2 2.063,2.417 2.448,2.594 0.385,0.177 10 false IG2D 0.052,0 0.208,0.167 0.156,0.167 10 false *a

Remove the No. 2 integration relay from the engine room relay block and junction block assembly.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A22-1 (IG2) - Body ground Power switch off 1 V or less
A22-2 (IG2D) - Body ground Power switch off 1 V or less


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


d.

Install the No. 2 integration relay.


e.

Reconnect the A22 power management control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR