Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.10–2014.11
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0343-747  Camshaft Position Sensor "A" Circuit High Input  


DESCRIPTION

Refer to the description for DTC P0340-886 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0340-886).

DTC No. INF Code DTC Detection Condition Trouble Area
P0343 747 GI signal is not input for 2 sec. or more while the engine is running.
·

SFI system

·

Inverter with converter assembly

·

ECM

·

Power management control ECU

·

Wire harness or connector



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0340-886 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0340-886).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (READY).

2.

With the vehicle stopped, push the P position switch (transmission shift main switch).

3.

Depress the accelerator pedal to start the engine.

4.

Depress the accelerator pedal and maintain the engine speed at 1000 rpm or more for 5 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (ENGINE AND ECT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Engine and ECT/ Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
SFI system DTCs are not output. A
Any of the following DTCs are output. B


DTC No. Relevant Diagnosis
P0340 Camshaft Position Sensor Circuit Malfunction
P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)
P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)


e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
None of the following DTCs are output. A
Any of the following DTCs are output. B


DTC No. Relevant Diagnosis
P0A1B (all INF codes)*1 Drive Motor "A" Control Module

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0343-747 may be set due to a malfunction which also causes the DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.




e.

Turn the power switch off.



A

3.CHECK DTC OUTPUT (HYBRID CONTROL)

B

3.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
P0340-886 is not output. A
P0340-886 is also output. B



e.

Turn the power switch off.



A

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

7.CHECK CONNECTOR CONNECTION CONDITION (ECM CONNECTOR)
4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



NOTICE:

Before disconnecting the connector, confirm that it is properly connected by checking that the locking claws are engaged and that the connector does not pull out.


A214648

b.

Check the connection of the low voltage connector of the inverter with converter assembly.

OK:

The connector is connected securely and there are no contact problems.


HINT:

When connecting the connector, insert it with the locking lever in the raised position. Rotate the lever downward and make sure that the connector is pulled into its socket. When the locking lever is in its fully closed position, a click will be heard as its locking claws engage. After the click is heard, pull up on the connector to confirm that it is properly connected.




OK

5.CHECK CONNECTOR CONNECTION CONDITION (ECM CONNECTOR)

NG

CONNECT SECURELY

5.CHECK CONNECTOR CONNECTION CONDITION (ECM CONNECTOR)

OK

6.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - ECM)

NG

CONNECT SECURELY

6.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - ECM)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A59 inverter with converter assembly connector.


c.

Disconnect the D28 ECM connector.


d.

Disconnect the A21 power management control ECU connector.


e.

Connect the cable to the negative (-) auxiliary battery terminal.


f.

Turn the power switch on (IG).


g.
A379058E01
1.417,1.75 1.833,2 0.417,0.25 1.333,4.083 1.75,4.333 0.417,0.25 0.573,3.24 1.083,2.417 true 0.75,1.75 1.031,1.156 true 0.135,0.094 0.688,0.354 0.552,0.26 10 false *a 0.167,2.188 0.719,2.448 0.552,0.26 10 false *b 0.656,1.771 1.208,2.031 0.552,0.26 10 false GI 1.49,1.792 2.042,2.052 0.552,0.26 10 false A59 1.146,2.281 1.698,2.542 0.552,0.26 10 false G2O 1.406,4.125 1.958,4.385 0.552,0.26 10 false D28

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A59-29 (GI) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Front view of wire harness connector
(to ECM)

NOTICE:

Turning the power switch on (IG) with the inverter with converter assembly connector and ECM connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



h.

Turn the power switch off.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A59-29 (GI) - D28-48 (G2O) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A59-29 (GI) or D28-48 (G2O) - Body ground and other terminals Power switch off 10 kΩ or higher



j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the A21 power management control ECU connector.


l.

Reconnect the D28 ECM connector.


m.

Reconnect the A59 inverter with converter assembly connector.



OK

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CONNECTOR CONNECTION CONDITION (ECM CONNECTOR)

OK

8.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - ECM)

NG

CONNECT SECURELY

8.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - ECM)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A59 inverter with converter assembly connector.


c.

Disconnect the D28 ECM connector.


d.

Disconnect the A21 power management control ECU connector.


e.
A379058E01
1.417,1.75 1.833,2 0.417,0.25 1.333,4.083 1.75,4.333 0.417,0.25 0.573,3.24 1.083,2.417 true 0.75,1.75 1.031,1.156 true 0.135,0.094 0.688,0.354 0.552,0.26 10 false *a 0.167,2.188 0.719,2.448 0.552,0.26 10 false *b 0.656,1.771 1.208,2.031 0.552,0.26 10 false GI 1.49,1.792 2.042,2.052 0.552,0.26 10 false A59 1.146,2.281 1.698,2.542 0.552,0.26 10 false G2O 1.406,4.125 1.958,4.385 0.552,0.26 10 false D28

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A59-29 (GI) - D28-48 (G2O) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A59-29 (GI) or D28-48 (G2O) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Front view of wire harness connector
(to ECM)


f.

Reconnect the A21 power management control ECU connector.


g.

Reconnect the D28 ECM connector.


h.

Reconnect the A59 inverter with converter assembly connector.



OK

9.CHECK HARNESS AND CONNECTOR (ECM - POWER MANAGEMENT CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (ECM - POWER MANAGEMENT CONTROL ECU)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the D28 ECM connector.


c.

Disconnect the A21 power management control ECU connector.


d.

Disconnect the A59 inverter with converter assembly connector.


e.
A379059E01
1.25,3.917 1.667,4.167 0.417,0.25 1.5,1.917 1.917,2.167 0.417,0.25 0.667,1.073 1.219,0.229 true 0.448,4.219 0.625,3.906 true 0.104,0.083 0.76,0.417 0.656,0.333 10 false *a 0.083,2.135 0.74,2.469 0.656,0.333 10 false *b 1.573,1.958 2.229,2.292 0.656,0.333 10 false D28 1.271,0.135 1.927,0.469 0.656,0.333 10 false G2O 1.323,3.958 1.979,4.292 0.656,0.333 10 false A21 0.313,4.24 0.969,4.573 0.656,0.333 10 false GI

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D28-48 (G2O) - A21-16 (GI) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D28-48 (G2O) or A21-16 (GI) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)
*b Rear view of wire harness connector
(to Power Management Control ECU)


f.

Reconnect the A59 inverter with converter assembly connector.


g.

Reconnect the A21 power management control ECU connector.


h.

Reconnect the D28 ECM connector.



OK

10.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A59 inverter with converter assembly connector.


c.
U154299E03
1.938,1.24 2.385,1.885 false 1.115,1.198 0.833,1.844 false 2.375,1.896 2.573,2.052 0.198,0.156 10 false GI 0.104,0.042 0.26,0.198 0.156,0.156 10 false *a 0.625,1.833 1.198,1.99 0.573,0.156 10 false GND1 0.219,1.031 0.49,1.198 0.271,0.167 10 false A59

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A59-29 (GI) - A59-28 (GND1) Power switch off 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Inverter with Converter Assembly)


d.

Reconnect the A59 inverter with converter assembly connector.



OK

11.CHECK POWER MANAGEMENT CONTROL ECU

NG

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

11.CHECK POWER MANAGEMENT CONTROL ECU
a.

Disconnect the A21 and L5 power management control ECU connectors.


b.
U154233E03
0.635,1.906 0.833,2.406 true 1.823,1.833 2.063,2.396 true 0.688,1.156 0.958,1.323 0.271,0.167 10 false A21 1.969,1.156 2.24,1.323 0.271,0.167 10 false L5 0.177,0.229 0.365,0.417 0.188,0.188 10 false *a 0.823,2.406 1.01,2.594 0.188,0.188 10 false GI 2.073,2.406 2.26,2.594 0.188,0.188 10 false E1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A21-16 (GI) - L5-6 (E1) Power switch off 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Power Management Control ECU)


c.

Reconnect the A21 and L5 power management control ECU connectors.



OK

NG