The MG ECU located in the inverter with converter assembly monitors its internal operation and it will set DTCs when it detects malfunctions.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0A1A | 151 | Run pulse signal cycle deviation or stop | ·
Inverter with converter assembly ·
Hybrid battery junction block assembly ·
Service plug grip |
| 155 | A/D converter error | Inverter with converter assembly | |
| 156 | CPU ROM-RAM error | ||
| 166 | R/D converter NM stop error | ||
| 658 | ALU error | ||
| 659 | Communication error (from MG1 to MG2) | ·
Inverter with converter assembly ·
Hybrid battery junction block assembly ·
Service plug grip |
|
| 791 | R/D converter communication error | Inverter with converter assembly | |
| P0A1B | 163 | IPM positive power source error | |
| 164 | IPM negative power source error | ||
| 192 | A/D converter error | ||
| 193 | CPU ROM-RAM error | ||
| 198 | R/D converter NM stop error | ||
| 511 | Standard voltage for analog signal offset error | ||
| 512 | Standard voltage for analog signal error | ||
| 661 | Communication error (from MG2 to MG1) | ||
| 786 | ALU error | ||
| 794 | R/D converter communication error |
If DTC P0A1A-151, P0A1A-155, P0A1A-658, P0A1A-659, P0A1A-791 DTC P0A1B-163, P0A1B-164, P0A1B-192, P0A1B-511, P0A1B-512, P0A1B-661, P0A1B-786 or P0A1B-794 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
Turn the power switch on (IG) and wait for 5 seconds or more.
If DTC P0A1A-156or P0A1B-193 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
Turn the power switch on (IG) and wait for 1 minute or more.
If DTC P0A1A-166 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
Turn the power switch on (READY).
With the vehicle stopped and park (P) selected, depress the accelerator pedal and start the engine.
Depress the accelerator pedal and keep the engine running for 30 seconds or more.
If DTC P0A1B-198 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
Turn the power switch on (READY).
Drive the vehicle at 3 mph (5 km/h) or more for 30 seconds or more.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| DTC P0A1A-151 or P0A1A-659 is output. | A |
| Other than above. | B |
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control /Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| Only DTC P0A1A-151, P0A1A-659 or P324E-788 is output. | A |
| DTC P0A94-172, P0A94-442, P0A94-553, P0A94-557, P3004-800 or P3004-801 is also output. | B |
| Other than above. | C |
Turn the power switch off.
A
B
C
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read and record the DTCs and freeze frame data.
Clear DTCs and freeze frame data.
Turn the power switch off.
NEXT
Connect the GTS to the DLC3.
Turn the power switch off and wait for 30 seconds or more.
Turn the power switch on (IG) and wait for 5 seconds or more.
Turn the power switch on (READY).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| No DTCs are output (not including history DTCs). | A |
| Only DTC P0A1A-151, P0A1A-659 or P324E-788 is output. | B |
| Other than above. | C |
Turn the power switch off.
C
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read and record the DTCs and freeze frame data.
Clear DTCs and freeze frame data.
Turn the power switch off.
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG) and wait for 5 seconds or more.
Turn the power switch on (READY) and wait for 5 seconds or more.
Depress the accelerator pedal with the engine stopped and park (P) selected to start the engine and idle it for 10 seconds or more.
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| No DTCs are output. | A |
| DTCs other than P0A94-442, P0A94-553, P0A94-557, P3004-800 or P3004-801 are output. | B |
| DTC P0A94-442, P0A94-553, P0A94-557, P3004-800 or P3004-801 is output. | C |
Turn the power switch off.
A
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>POWER MODULE INTELLIGENT TRANSISTOR>COMPONENTS)
B
C
Check the installation position of the part No. label on the inverter with converter assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).
Check the part number of the inverter with converter assembly.
| Result | Proceed to | |
|---|---|---|
| Installation Position of Part No. Label | Part No. | |
| Front | - | A |
| Top | ·
G9200-47160 ·
G9200-47161 ·
G9200-47162 |
|
| Other than above. | B | |
A
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL COMPUTER>COMPONENTS)
B
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL COMPUTER>COMPONENTS)
Check the installation position of the part No. label on the inverter with converter assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).
Check the part number of the inverter with converter assembly.
| Result | Proceed to | |
|---|---|---|
| Installation Position of Part No. Label | Part No. | |
| Front | - | A |
| Top | ·
G9200-47160 ·
G9200-47161 ·
G9200-47162 |
|
| Other than above. | B | |
A
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>POWER MODULE INTELLIGENT TRANSISTOR>COMPONENTS)
B
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>POWER MODULE INTELLIGENT TRANSISTOR>COMPONENTS)
Check the installation position of the part No. label on the inverter with converter assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).
Check the part number of the inverter with converter assembly.
| Result | Proceed to | |
|---|---|---|
| Installation Position of Part No. Label | Part No. | |
| Front | - | A |
| Top | ·
G9200-47160 ·
G9200-47161 ·
G9200-47162 |
|
| Other than above. | B | |
A
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>POWER MODULE INTELLIGENT TRANSISTOR>COMPONENTS)
B
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>POWER MODULE INTELLIGENT TRANSISTOR>COMPONENTS)