Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.03–2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0851-579  Park / Neutral Switch Input Circuit Low  P0852-580  Park / Neutral Switch Input Circuit High  


DESCRIPTION

Instead of having a parking position as one of the positions of the conventional shift lever, a P position switch (transmission shift main switch) is provided independently above the shift lever. The switch is a momentary type, in which the button does not lock mechanically.

The P position switch (transmission shift main switch) contains resistors R1 and R2. When the P position switch (transmission shift main switch) is not pressed, the switch provides a combined resistance of R1 and R2; and when the P position switch (transmission shift main switch) is pressed, the switch provides only the resistance of R1. The voltage at the P1 terminal of the power management control ECU varies with the changes in the resistance of the switch. The power management control ECU determines the P position switch (transmission shift main switch) operation according to this resistance signal.


DTC No. INF Code DTC Detection Condition Trouble Area
P0851 579 GND short in P position switch circuit
·

Wire harness or connector

·

P position switch (Transmission shift main switch)

·

Power management control ECU


P0852 580 Open or +B short in P position switch circuit

WIRING DIAGRAM

A216493E45
5.323,1.938 6.667,2.302 1.344,0.365 10 false Power Management Control ECU 5.521,0.938 5.729,1.125 0.208,0.188 10 false P1 5.323,1.771 5.531,1.958 0.208,0.188 10 false L5 2.146,1.573 4.219,1.927 2.073,0.354 10 false P Position Switch (Transmission Shift Main Switch) 5.281,0.854 5.49,1.042 0.208,0.188 10 false 16 4.021,0.854 4.177,1.042 0.156,0.188 10 false 4 3.833,0.854 3.979,1.042 0.146,0.188 10 false S 3.25,1.146 3.51,1.333 0.26,0.188 10 false R2 2.625,1.146 2.833,1.333 0.208,0.188 10 false R1 2.427,0.854 2.594,1.042 0.167,0.188 10 false E 2.229,0.854 2.365,1.042 0.135,0.188 10 false 2 2.146,1.406 2.583,1.594 0.438,0.188 10 false L124

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 5 seconds or more.



PROCEDURE

1.INSPECT P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH)
a.

Disconnect the L124 P position switch (transmission shift main switch) connector.


b.
U154314E02
2.073,1.208 2.125,1.552 false 1.781,1.198 1.719,1.552 false 2.271,1.073 2.125,1.25 false 1.292,1.073 1.156,1.25 false 0.115,0.083 0.365,0.271 0.25,0.188 10 false *a 1.646,1.573 1.802,1.75 0.156,0.177 10 false S 2.094,1.573 2.25,1.75 0.156,0.177 10 false E 0.406,1.042 0.74,1.208 0.333,0.167 10 false L124

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L124-4 (S) - L124-2 (E) Switch pressed 680 Ω
L124-4 (S) - L124-2 (E) Switch released 4580 Ω


Text in Illustration
*a Component without harness connected
(P Position Switch (Transmission Shift Main Switch))

HINT:

Terminals No. 1 and No. 8 on the component side connector are empty.



c.

Reconnect the L124 P position switch (transmission shift main switch) connector.



OK

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH))

NG

REPLACE P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH)

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH))
a.

Disconnect the L5 power management control ECU connector.


b.

Disconnect the L124 P position switch (transmission shift main switch) connector.


c.
A379062E01
0.417,3.583 0.833,3.833 0.417,0.25 1.833,2.5 2.25,2.75 0.417,0.25 1.552,2.042 1.813,1.969 false 1.594,4.146 1.646,3.813 false 0.094,0.104 0.552,0.375 0.458,0.271 10 false *a 1.281,1.979 1.74,2.25 0.458,0.271 10 false P1 1.948,2.542 2.406,2.813 0.458,0.271 10 false L5 0.146,2.854 0.604,3.125 0.458,0.271 10 false *b 0.469,3.625 0.927,3.896 0.458,0.271 10 false L124 1.531,4.167 1.99,4.438 0.458,0.271 10 false S

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L5-16 (P1) - L124-4 (S) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
L5-16 (P1) or L124-4 (S) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to P Position Switch (Transmission Shift Main Switch))

HINT:

As necessary, check that there is no short to power supply wires when performing the above wire harness inspection.



d.

Reconnect the L124 P position switch (transmission shift main switch) connector.


e.

Reconnect the L5 power management control ECU connector.



OK

3.CHECK HARNESS AND CONNECTOR (P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH) - BODY GROUND)
a.

Disconnect the L124 P position switch (transmission shift main switch) connector.


b.
U154745E02
1.385,1.292 1.313,1.615 false 0.208,0.135 0.479,0.323 0.271,0.188 10 false *a 1.219,1.615 1.375,1.792 0.156,0.177 10 false E 0.5,1.073 0.844,1.24 0.344,0.167 10 false L124

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L124-2 (E) - Body ground Power switch off Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to P Position Switch (Transmission Shift Main Switch))


c.

Reconnect the L124 P position switch (transmission shift main switch) connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR