Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.03–2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0516-769  Battery Temperature Sensor Circuit Low  P0517-770  Battery Temperature Sensor Circuit High  


DESCRIPTION

The thermistor assembly detects the auxiliary battery temperature. The resistance of the thermistor assembly built into the thermistor changes in accordance with changes in the auxiliary battery temperature. The lower the auxiliary battery temperature, the higher the thermistor assembly resistance. Conversely, the higher the temperature, the lower the resistance. The thermistor assembly is connected to the power management control ECU. A voltage of 5 V is supplied to the thermistor assembly from the THB terminal of the power management control ECU through its internal resistor R. This means that resistor R and the thermistor assembly are connected in series. The voltage at the THB terminal and the resistance value change in accordance with changes in the auxiliary battery temperature. Based on this signal, the power management control ECU reduces the charging current when the auxiliary battery temperature is high to protect the auxiliary battery.

HINT:

Characteristics of the thermistor assembly resistance (reference values) are as follows.

Terminal THB
(with Connector Disconnected)
Resistance Ambient Temperature
THB - E2 4.5 to 5.5 V 3.00 to 3.73 kΩ Approximately 10°C (50°F)
1.60 to 1.80 kΩ Approximately 25°C (77°F)
0.80 to 1.00 kΩ Approximately 40°C (104°F)


A180218E03
2.119,0.38 2.239,0.531 0.120,0.151 10 6 2.115,0.663 2.226,0.814 0.111,0.151 10 5 2.108,0.943 2.223,1.094 0.115,0.151 10 4 2.111,1.223 2.226,1.374 0.115,0.151 10 3 2.116,1.495 2.236,1.646 0.120,0.151 10 2 2.116,1.781 2.227,1.932 0.111,0.151 10 1 0.832,1.148 1.866,1.299 1.034,0.151 10 Resistance (kΩ) 5.413,2.332 6.816,2.483 1.402,0.151 10 Temperature (°C (°F)) 2.623,2.262 2.809,2.413 0.186,0.151 10 10 2.567,2.413 2.847,2.564 0.281,0.151 10 (50) 2.974,2.413 3.255,2.564 0.281,0.151 10 (68) 3.362,2.413 3.643,2.564 0.281,0.151 10 (86) 3.73,2.413 4.091,2.564 0.361,0.151 10 (104) 4.151,2.413 4.520,2.564 0.369,0.151 10 (122) 4.552,2.413 4.941,2.564 0.390,0.151 10 (140 ) 4.964,2.413 5.337,2.564 0.372,0.151 10 (158) 3.016,2.262 3.214,2.413 0.198,0.151 10 20 3.411,2.262 3.608,2.413 0.197,0.151 10 30 3.834,2.262 4.024,2.413 0.191,0.151 10 40 4.235,2.262 4.444,2.413 0.209,0.151 10 50 4.657,2.248 4.862,2.399 0.206,0.151 10 60 5.043,2.248 5.244,2.399 0.200,0.151 10 70 2.124,2.056 2.232,2.206 0.107,0.151 10 0 2.258,2.262 2.384,2.413 0.127,0.151 10 0 2.186,2.413 2.471,2.564 0.286,0.151 10 (32)


DTC No. INF Code DTC Detection Condition Trouble Area
P0516 769 Malfunction in the thermistor assembly circuit (short to GND)
·

Thermistor assembly

·

Wire harness or connector

·

Power management control ECU


P0517 770 Malfunction in the thermistor assembly circuit (open or short to +B)

WIRING DIAGRAM

A259938E57
4.479,3 6.615,3.365 2.135,0.365 10 false Power Management Control ECU 4.479,2.833 4.792,3.146 0.313,0.313 10 false L5 1.26,3.115 2.802,3.479 1.542,0.365 10 false Thermistor Assembly 1.271,2.958 1.802,3.115 0.531,0.156 10 false S17 2.146,1.083 2.458,1.281 0.313,0.198 10 false THB 2.542,1.083 2.677,1.281 0.135,0.198 10 false 2 2.542,2.083 2.677,2.281 0.135,0.198 10 false 1 4.563,1.083 4.76,1.281 0.198,0.198 10 false 28 4.573,2.083 4.771,2.281 0.198,0.198 10 false 30 2.25,2.083 2.458,2.281 0.208,0.198 10 false E2 4.802,1.083 5.115,1.281 0.313,0.198 10 false THB 4.833,2.083 5.271,2.281 0.438,0.198 10 false ETHB

CAUTION / NOTICE / HINT

HINT:
·

Read the freeze frame data using the GTS. In the freeze frame data, some information is recorded about the vehicle conditions at the moment a malfunction occurred. This information can be helpful when troubleshooting.

·

After confirming that DTC P0516-769 or P0517-770 is output, use the GTS to check "Auxiliary Batt Temperature" in the Hybrid Control Data List.

Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short circuit or short to GND

·

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

(a)

Turn the power switch on (IG) and wait for 5 seconds or more.




PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

2.READ VALUE USING GTS (AUXILIARY BATT TEMPERATURE)

NG

CONNECT SECURELY

2.READ VALUE USING GTS (AUXILIARY BATT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.


d.

Read the Data List.

Result:
Result Proceed to
-40°C (-40°F) A
215°C (419°F) B
Same as actual temperature C



e.

Turn the power switch off.



A

3.READ VALUE USING GTS (CHECK FOR OPEN)

B

5.READ VALUE USING GTS (CHECK FOR SHORT)

C

3.READ VALUE USING GTS (CHECK FOR OPEN)
a.
A252923

Disconnect the S17 thermistor assembly connector.


b.
U154388E02
1.594,1.229 1.229,1.594 false 1.813,1.219 2.229,1.594 false 0.531,0.969 0.813,1.135 0.281,0.167 10 false S17 0.146,0.094 0.344,0.271 0.198,0.177 10 false *a 2.052,1.594 2.375,1.771 0.323,0.177 10 false THB 1.094,1.594 1.313,1.771 0.219,0.177 10 false E2

Connect terminals 2 (THB) and 1 (E2) of vehicle side connector S17 of the thermistor assembly.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.


f.

Read the Data List.

Result:
Tester Display Condition Specified Condition
Auxiliary Batt Temperature Terminals THB and E2 connected.
Power switch on (IG)
215°C (419°F)


Text in Illustration
*a Front view of wire harness connector
(to Thermistor Assembly)


g.

Turn the power switch off.


h.

Reconnect the S17 thermistor assembly connector.



OK

REPLACE THERMISTOR ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - THERMISTOR ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - THERMISTOR ASSEMBLY)
a.
U154411E03
2.188,1.906 1.948,2.333 false 2.292,1.906 2.531,2.333 false 2.021,2.646 2.302,2.813 0.281,0.167 10 false L5 0.177,0.156 0.448,0.323 0.271,0.167 10 false *a 2.427,2.344 2.74,2.51 0.313,0.167 10 false THB 1.729,2.333 2.125,2.5 0.396,0.167 10 false ETHB

Connect terminals 28 (THB) and 30 (ETHB) of connector L5 of the power management control ECU.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.


e.

Read the Data List.

Result:
Tester Display Condition Specified Condition
Auxiliary Batt Temperature Terminals THB and ETHB connected.
Power switch on (IG)
215°C (419°F)


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)


f.

Turn the power switch off.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

5.READ VALUE USING GTS (CHECK FOR SHORT)
a.
A252923

Disconnect the S17 thermistor assembly connector.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.


e.

Read the Data List.

Result:
Tester Display Condition Specified Condition
Auxiliary Batt Temperature Power switch on (IG) -40°C (-40°F)



f.

Turn the power switch off.


g.

Reconnect the S17 thermistor assembly connector.



OK

REPLACE THERMISTOR ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - THERMISTOR ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - THERMISTOR ASSEMBLY)
a.

Disconnect the S17 thermistor assembly connector.


b.
A379049E01
1.083,3.667 1.5,3.917 0.417,0.25 2.333,1.083 2.75,1.333 0.417,0.25 1.031,1.677 1.448,1.26 false 2.219,1.729 1.75,1.271 false 1.771,4.302 2.188,3.885 false 2.76,4.344 2.292,3.885 false 0.094,0.177 0.573,0.5 0.479,0.323 10 false *a 2.406,1.125 2.885,1.448 0.479,0.323 10 false S17 0.927,1.708 1.406,2.031 0.479,0.323 10 false E2 2.146,1.771 2.625,2.094 0.479,0.323 10 false THB 1.198,3.708 1.677,4.031 0.479,0.323 10 false L5 0.115,1.948 0.594,2.271 0.479,0.323 10 false *b 2.656,4.365 3.146,4.656 0.49,0.292 10 false THB 1.594,4.344 2.083,4.635 0.49,0.292 10 false ETHB

Disconnect the L5 power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L5-28 (THB) - S17-2 (THB) Power switch off Below 1 Ω
L5-30 (ETHB) - S17-1 (E2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
L5-28 (THB) or S17-2 (THB) - Body ground and other terminals Power switch off 10 kΩ or higher
L5-30 (ETHB) or S17-1 (E2) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Thermistor Assembly)
*b Rear view of wire harness connector
(to Power Management Control ECU)


d.

Reconnect the S17 thermistor assembly connector.


e.

Reconnect the L5 power management control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR